Panasonic Smoke Alarm 6295 User Manual

Fire alarm systems  
Enclosed heat  
detectors 6295, 6296,  
6297 and 6298  
Fixed temperature alarm level  
ATEX compliance  
Waterproof (IP67)  
Fixed temperature alarm level  
Waterproof connection box  
The detectors are conventional fixed  
temperature heat detectors, i.e. they will give  
an alarm within a response temperature  
range in accordance with EN54-5:2000.  
The heat pick-up shield, the LED, all  
electronics, etc. are mounted in a grey water-  
proof detector housing, to be mounted on the  
attached connection box, which has three  
cable inlets. Three compression glands and  
a silicon gasket for IP67 are also attached.  
The sensing element is a heat pick-up shield  
and a bimetal switch.  
An LED on the detector (not on 6298) will  
light up when the detector goes into alarm.  
The detector also has an output for an  
external LED 2216 / 2217.  
Label holder  
A label holder intended for a label showing  
"zone number", can be mounted in the  
connection box.  
The following types are available (static  
response temperature, class & EN54-5 temp.  
range):  
Miscellaneous  
The detectors 6295-6298 are provided with  
three pairs of flying leads with female push-  
on connectors, see figure on the opposite  
side of this page. (Zone line cables (in / out)  
and an external LED.)  
6295, 57°C, class A2 S (54 to 70°C).  
6296, 72°C, class B S (69 to 85°C).  
6297, 87°C, class C S (84 to 100°C).  
6298, 117°C, class E S (114 to 130°C).  
Product applications  
Latching  
The detectors can be used in the systems  
EBL500 / 512 / 128 / 1000 / 2000 provided  
with some zone line inputs for the system  
respectively (e.g. an 8 zones expansion  
board 1580 / 4580 input, an addressable  
zone interface 2226 / 2335 input, an  
addressable multi purpose I/O unit 3361  
input, etc.).  
The detectors are latching, i.e. they will not  
be automatically reset if the temperature,  
after the alarm, falls below the detector's  
static response temperature. The detector's  
LED and a connected ext. LED will be lit  
until the detector is reset via the c.i.e.  
ATEX classification  
Heat detectors are normally used in rooms  
where the temperature can be expected to  
rise rapidly in case of a fire or places where  
smoke detectors can not be used.  
The detectors 6295 and 6296 complies with  
the ATEX classification Ex II 3GD EEx nA  
II T5. See also the opposite side of this  
page.  
The detectors are intended for outdoor use or  
indoor use in high humidity premises.  
Panasonic Electric Works Fire & Security Technology Europe AB  
Jungmansgatan 12, SE-211 19 Malmö, Sweden  
Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99  
 

Miele Clothes Dryer T 1413 T 1415 User Manual
Multi Tech Systems Network Card CF220 User Manual
NETGEAR Network Router RT338 User Manual
NewAir Air Conditioner ACP 1400E User Manual
Nikon Digital Camera S6400 User Manual
NordicTrack Treadmill NATL822050 User Manual
NordicTrack Treadmill NTL14940 User Manual
Nortel Networks Telephone Business Communications Manager 25 User Manual
Outback Power Systems Power Supply FX User Manual
Palsonic Flat Panel Television TFTV812U User Manual