Panasonic Outdoor Ceiling Fan FV 08VSL2 User Manual

SUPPLEMENTARY  
INSTALLATION INSTRUCTIONS  
Ventilating Fan  
(Contractor Pack)  
Model No.  
FV-08VSLA2  
Contents  
General Safety lnformation  
Unpacking  
2-3  
3
Supplied Accessories  
Wiring Diagram  
4
4
lnstallation (Joist Mounting- )  
5-7  
7-8  
Housing Can  
FV-08VSLA2  
lnstallation (Joist Mounting-  
)
lnstallation  
lnstallation  
(
-Joist Mounting)  
9
9-10  
(Between Joist Mounting)  
lnstallation (Wooden Header)  
11  
lnstallation  
(ln Existing Construction)  
Back cover  
Product Service  
Back cover  
Motor/Light Kit/Grille Assembly  
FV-08VSLB2, FV-10VSLB2  
Applicable to Model:  
FV-08VSL2, FV-10VSL2  
READ AND SAVE THESE INSTRUCTIONS  
Thank you very much for having purchased our product.  
Please read these instructions carefully before attempting to install, operate or service  
the Panasonic product. Failure to comply with instructions could result in personal injury  
or property damage. Please explain to users how to operate and maintain the product  
after installation, and this booklet should be presented to users.  
Please retain this booklet for future reference.  
 
GENERAL SAFETY INFORMATION CONTINUED  
CAUTION:  
1. Do not install this ventilating fan where interior room temperature may exceed 104 F (40 C).  
2. Make sure that the electric service supply voltage is AC 120V, 60 Hz.  
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the  
Occupation Safety and Health Act (OSHA).  
4. Always disconnect the power source before working on or near the fan, motor, light fixture or  
junction box.  
5. Protect the supply wiring from sharp edges, oil, grease, hot surfaces, chemicals or other objects.  
6. Do not kink the supply wiring.  
7. Provide make up air for proper ventilation.  
8. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and  
vapors.  
9. Do not install the unit where ducts are configured as shown in Fig. A.  
Adaptor  
Prohibition  
Prohibition  
Prohibition  
Prohibition  
Fig. A  
10. Not for use in cooking area. (Fig. B)  
(Cooking area)  
Do not install above or  
inside this area  
Floor  
Cooking  
equipment  
Fig. B  
UNPACKING  
Unpack and carefully remove unit from carton.  
Refer to the Supplied Accessories list to verify that all parts are present.  
3
 
SUPPLIED ACCESSORIES (4 sets)  
(A) For Motor/ Light Kit/ Grille Assembly of model: FV-08VSLB2, FV-10VSLB2  
Appearance  
Appearance  
Quantity  
4
Quantity  
4
Part name  
Grille  
Part name  
Lighting unit  
32W  
Fluorescent  
lamp  
Screw  
(ST4.2X16)  
4
4
8
4
4W  
Machine screw  
(M4X8)  
Night lamp  
(B) For Housing Can of model: FV-08VSLA2  
Appearance  
Appearance  
Quantity  
Quantity  
8
Part name  
Part name  
Screw  
(ST4.2X8)  
Suspension  
bracket  
4
Long screw  
(ST4.2X20)  
24  
Suspension  
bracket  
4
4
Machine screw  
(M4X8)  
4
8
Suspension  
bracket  
Screw  
(ST4.2X12)  
WIRING DIAGRAM  
Wiring diagram  
Night lamp  
White  
Black  
Fluorescent  
lamp  
Electronic ballast  
Lighting unit  
Live (Light)  
Neural  
Black  
White  
Fan body  
White  
Black  
Red  
Black  
White  
Black  
Live (N.Light)  
Neural  
Capacitor  
White  
Black  
White  
Power supply  
AC120V 60Hz  
Motor  
Live  
Fuse in motor  
Thermally protected  
Earth ground  
Junction box  
Green  
Green  
4
 
INSTALLATION (JOIST MOUNTING- )  
1. Before installation, secure the fan body to adaptor by  
Machine screw  
using machine screw(M4X8). (Fig.1)  
(M4X8)  
IMPORTANT:  
Remove the tape from damper and adaptor  
Fan body  
before installation. As shown below:  
Fig. 1  
Tape  
A=12 inches  
Adaptor  
Damper  
Suspension  
bracket  
2. lnsert the suspension bracket into the fan body and  
adaptor. (Select the suspension bracket as shown below)  
Fan body  
Fig. 2-1  
A=16 inches  
Suspension  
bracket  
Suspension  
bracket  
Fan body  
Fig. 2-2  
Joists  
A=19.2 inches(vertical joist)  
Spacing A on center joists lnsert Suspension bracket  
Refer to Fig. 2-1  
Refer to Fig. 2-2  
Refer to Fig. 2-3  
Refer to Fig. 2-4  
12 inches  
Suspension  
bracket  
16 inches  
19.2 inches vertical joists  
24 inches  
Suspension  
bracket  
Fig. 2-3  
Fan body  
lf spacing A on center joists is 24 inches, connect  
suspension bracket and  
as shown below:  
A=24 inches  
Suspension  
bracket  
(C4 mark to C4 mark)  
Suspension  
bracket  
2 Screw (ST4.2X8)  
Suspension bracket  
Suspension bracket  
Suspension  
bracket  
Fan body  
Fig. 2-4  
5
 
INSTALLATION (JOIST MOUNTING- ) CONTINUED  
3. Install the suspension bracket and the flange of fan  
body to joists by using long screws (ST4.2X20).  
Joist  
(If spacing A between joists is 10 1/4 12 inches,  
~
install the flange of fan body according to Fig.3-2,  
Fan body  
others according to Fig.3-1 install the product.)  
4 Long screws (ST4.2X20)  
Fig. 3-1  
4. Install the suspension bracket to joists by using long  
screws (ST4.2X20) and secure it to the fan body by  
using screw (ST4.2X12). (Fig.4)  
A=10 1/4 12 inches  
~
Joist  
5. Remove junction box cover and secure conduit or  
stress relief to junction box knock-out hole. (Fig.5)  
2 Long screws  
(ST4.2X20)  
Fan body  
Fig. 3-2  
Joist  
6. Refer to wiring diagram (page 4).  
Using wire nuts, connect house power wires to  
ventilating fan wires and lighting unit wires:  
black to black; white to white; green to green;  
Replace the junction box cover. (Fig.5)  
2 Long screws  
(ST4.2X20)  
Screw  
(ST4.2X12)  
Fig. 4  
Knock-out hole  
Circular duct  
CAUTION:  
Mount junction box cover carefully so that lead  
wires are not pinched.  
Conduit  
Joist  
Duct tape  
Junction box  
cover  
7. Squeeze the circular duct to fit the adaptor,  
then slipped onto the adaptor and secure  
it with duct tape.  
Conduit  
Junction box  
Squeeze  
Wire nut  
Green wires  
Lead wires  
Fig. 5  
6
 
INSTALLATION (JOIST MOUNTING- ) CONTINUED  
8. Finish ceiling work. Ceiling hole should be aligned  
with the edge of the flange. (Fig.6)  
9.Follow the Fig.12-3,12-4(page 9) and the Fig.6,7  
(page 8) of the original installation instruction to  
complete the Motor/Light Kit/Grille Assembly  
installation.  
Ceiling  
Fig. 6  
Unit: inches (mm)  
INSTALLATION (JOIST MOUNTING- )  
1. Disconnect plug connector from receptacle and  
Adaptor  
remove adaptor from fan body before starting  
installation.  
2. Insert the suspension bracket into the adaptor and  
secure it to joists by using long screws (ST4.2X20).  
2 Long screws  
(Fig.7)  
(ST4.2X20)  
Joists  
CAUTION:  
Backside of flange should mount directly to bottom  
of joist.  
If spacing A between joists is 21 1/4 to 23 1/2  
2 Long screws  
(ST4.2X20)  
inches, connect suspension bracket and  
(C4 mark to C4 mark) according to page 5.  
Select the suspension bracket according to  
spacing A as shown below.  
Adaptor  
Suspension bracket  
Spacing A  
13 1/4~15 1/2  
16 1/2~18 3/4 21 1/4~23 1/2  
13 1/4~15 1/2(336~394)  
16 1/2~18 3/4(419~480)  
21 1/4~23 1/2(540~597)  
between Joists  
inches (mm)  
(336~394)  
(419~480)  
(540~597)  
suspension  
bracket  
suspension  
bracket  
suspension  
bracket  
suspension  
bracket  
&
3. Follow step 5 to 7 of the installation (page 6) to  
complete the duct work and wiring.  
4. Insert the suspension bracket into fan body  
(refer to step 2 of Installation , page 5).  
Unit: inches (mm)  
Fig. 7  
7
 
INSTALLATION (JOIST MOUNTING- ) CONTINUED  
5. Insert the fan body into joists. (Fig.8)  
Circular duct  
Conduit  
IMPORTANT:  
Joist  
Make sure that adaptor claws are properly inserted  
into body slots.  
Junction box cover  
6. Secure the fan body to adaptor by using machine  
screw. (Fig.9)  
7. Secure the suspension bracket to joists by using  
long screws (ST4.2X20) and secure it to fan body  
by using screw (ST4.2X12) in vertical direction.  
(Fig.9)  
Fan body  
8. Follow step 8 to 9 of installation (page 7) to  
complete the installation work.  
Adaptor  
claws  
Fig. 8  
Screw (ST4.2X12)  
2 Long screws  
(ST4.2X20)  
Machine  
screw  
Joist  
Fig. 9  
8
 
INSTALLATION  
( -JOIST MOUNTING )  
4 kinds of -joist  
hole  
inches (mm)  
mark  
Suspension  
bracket  
9/16 (14.3)  
C1  
C2  
C3  
C4  
11/16 (17.5)  
31/32 (24.6)  
1 17/32 (38.9)  
C
Screw  
(ST4.2X12)  
C3  
C4  
C1  
Fig. 10  
C2  
Suspension bracket  
The suspension bracket  
different kinds of -joist.  
can comply with  
1. Before installation, secure the fan body to adaptor by  
using machine screw (M4X8). (Fig.1 of page 5)  
2. Connect the suspension bracket  
to fan body. (Fig.10)  
(Select the hole by checking -joist size fix the screw  
to the frame hole.)  
3. Connect the ventilating fan to the -joist. (Fig.11)  
4 Long screws  
(ST4.2X20)  
I-joist  
4. Follow step 5 to 9 of installation (page 6 page 7) to  
~
Fig. 11  
complete the installation work.  
INSTALLATION  
( BETWEEN JOIST MOUNTING )  
1. Before installation, secure the fan body to adaptor by  
using machine screw (M4X8). (Fig.1 of page 5)  
A
16 inches and 19.2 inches  
horizontal joist  
19.2 inches vertical joist  
A=16 inches and 19.2 inches horizontal joist  
Suspension bracket  
2. Insert the suspension bracket into bracket cover of  
adaptor side and the back of the fan body.  
(Fig.12-1,12-2)  
(select the suspension bracket according to spacing  
A as shown right)  
Suspension bracket  
Suspension bracket  
Fig. 12-1  
A=19.2 inches vertical joist  
Suspension bracket  
Suspension bracket  
Suspension bracket  
Fig. 12-2  
9
 
INSTALLATION  
(BETWEEN JOIST MOUNTING ) CONTINUED  
3. Insert the fan body between joists.  
Make sure the fan body is level and square  
(perpendicular) with the joists. (Fig.13)  
Joists  
CAUTION:  
Backside of flange should mount directly to bottom  
Adaptor  
of joist.  
Junction box  
Fan body  
Suspension bracket  
13 1/4 15 1/2(336 394)  
~
16 1/2 18 3/4(419 480)  
~
~
~
21 1/4 23 1/2(540 597)  
~
~
Fig. 13  
Unit: inches (mm)  
4. Secure the suspension bracket to joists by using long  
screws (ST4.2X20). (Fig.14, Fig.15)  
Joist  
2 Long screws  
(ST4.2X20)  
5. Secure the suspension bracket to fan body by using  
screws (ST4.2X12). (Fig.15)  
Fig. 14  
6. Follow step 5 to 9 of installation (page 6 page 7)  
~
to complete the installation work.  
4 Long screws  
(ST4.2X20)  
2 Screw  
(ST4.2X12)  
Joist  
Fig. 15  
10  
 
INSTALLATION (WOODEN HEADER )  
1. Before installation, secure the fan body to adaptor by  
using machine screw (M4X8). (Fig.1 of page 5)  
Joist  
Header  
Joist  
Adaptor  
Fan body  
2. Install header between joists by using nails or screws.  
Fig. 16  
Unit: inches (mm)  
3. Install the fan body and secure it by using long  
screws (ST4.2X20). (Fig.16, Fig.17)  
Circular duct  
Junction box  
6 Long screws  
(ST4.2X20)  
Conduit  
Junction box  
Wire nut  
Green wires  
4. Follow step 5 to 9 of installation (page 6 page 7)  
~
to complete the installation work.  
Lead wires  
Fig. 17  
11  
 
INSTALLATION  
(IN EXISTING CONSTRUCTION )  
1. Installation in existing construction.  
Installing the fan body in an existing building requires an accessible area (attic or crawl space) above  
the planning installation location or existing ducting and wiring.  
(1) To install the fan body, follow the procedures described in lnstallation . Take the following  
precautions before installation.  
CAUTION:  
Check area above planning installation location to be sure that:  
1. Duct work can be done and that area is sufficient for proper ventilation.  
2. Wiring can be run to planning location.  
3. No wiring or other obstructions shall interfere with installation.  
(2) Inspect duct work and wiring before proceeding with installation.  
(3) Plan suitable location for fan body. (next to ceiling joist)  
(4) Before installation, provide inspection and maintenance access at a location that will not interfere  
with installation work shown in installation  
(5) First, remove ceiling section according to Fig.6 of page 7.  
(6) Install fan body.  
2. Installation from accessible area above fan location.  
(1) Inspect duct work and wiring before proceeding with installation.  
(2) Remove ceiling section according to Fig.6 of page 7.  
(3) Install fan body.  
PRODUCT SERVICE  
Warning Concerning Removal of Covers.  
The unit should be serviced by qualified technicians only.  
Your product is designed and manufactured to ensure a minimum of maintenance.  
Should your unit require service or parts, call Panasonic Call Center at 1-866-292-7292 (USA)  
or 1-800-669-5165 (Canada).  
Panasonic Corporation of North America  
One Panasonic Way, Secaucus, New Jersey 07094  
Panasonic Canada lnc.  
5770 Ambler Drive, Mississauga, Ontario L4W 2T3  
Panasonic corporation 2012  
Printed in China  
T0212-0 08VSLA220  
 

Miele Dishwasher G 851 User Manual
Miele Washer W2859iWPM SUPERTRONIC User Manual
Milwaukee Grinder 41349 B User Manual
NEC Cordless Telephone 92600MFH05 User Manual
NuTone Vacuum Cleaner CV400 User Manual
Nuvo MP3 Docking Station NV RIPR1 User Manual
Omega Automobile Parts HHT 1500 User Manual
Onkyo Speaker System HT RC370 User Manual
Oregon Scientific Clock RRM612P User Manual
Panasonic Telephone KXTGA935 User Manual