Panasonic Network Card 2SB1679 User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SB1679  
Silicon PNP epitaxial planar type  
For low-frequency amplification  
Unit: mm  
+0.10  
+0.1  
–0.0  
0.15  
0.3  
–0.05  
Features  
3
Large collector output capacitance (Common base, input open cir-  
cuited) Cob  
Low collector-emitter saturation voltage VCE(sat)  
S-Mini type package, allowing downsizing of the equipment and  
automatic insertion through the tape packing  
1
2
(0.65) (0.65)  
1.3 0.1  
2.0 0.2  
Absolute Maximum Ratings Ta = 25°C  
10°  
Parameter  
Symbol  
Rating  
15  
Unit  
V
Collector-base voltage (Emitter open) VCBO  
Collector-emitter voltage (Base open) VCEO  
Emitter-base voltage (Collector open) VEBO  
1: Base  
2: Emitter  
3: Collector  
10  
V
7  
V
EIAJ: SC-70  
SMini3-G1 Package  
Collector current  
IC  
ICP  
PC  
Tj  
0.5  
1  
A
Peak collector current  
Collector power dissipation  
Junction temperature  
Storage temperature  
A
Marking Symbol: 3V  
150  
mW  
°C  
°C  
150  
Tstg  
55 to +150  
Electrical Characteristics Ta = 25°C 3°C  
Parameter  
Symbol  
VCBO  
VCEO  
VEBO  
ICBO  
Conditions  
Min  
15  
10  
7  
Typ  
Max  
Unit  
V
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector-base cutoff current (Emitter open)  
IC = −10 µA, IE = 0  
IC = −1 mA, IB = 0  
V
IE = −10 µA, IC = 0  
VCB = −10 V, IE = 0  
VCE = −2 V, IC = − 0.5 A  
VCE = −2 V, IC = −1 A  
V
100  
nA  
1
2
Forward current transfer ratio *  
hFE1  
hFE2  
130  
60  
350  
*
1
Collector-emitter saturation voltage *  
VCE(sat) IC = − 0.4 A, IB = −8 mA  
0.16 0.30  
V
V
1
Base-emitter saturation voltage *  
VBE(sat) IC = − 0.4 A, IB = −8 mA  
0.8  
130  
22  
1.2  
Transition frequency  
fT  
VCB = −10 V, IE = 50 mA, f = 200 MHz  
VCB = −10 V, IE = 0, f = 1 MHz  
MHz  
pF  
Collector output capacitance  
Cob  
(Common base, input open circuited)  
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
2. 1: Pulse measurement  
*
2: Rank classification  
*
Rank  
R
S
hFE1  
130 to 220  
180 to 350  
Publication date: February 2003  
SJC00097BED  
1
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Miele Washer W 1623 User Manual
Nikon Scanner AF 10 User Manual
NordicTrack Treadmill 4200 R User Manual
Nuvo Stereo System NV MP User Manual
Omnimount Indoor Furnishings 1004263 User Manual
OPTI UPS Power Supply IS1700NT User Manual
Oregon Scientific Camcorder AC01 18 User Manual
Panasonic Blu ray Player DMP BD45 User Manual
Panasonic Switch KX HNB600 User Manual
Parasound Stereo Amplifier HCA 1201A User Manual