Panasonic Network Card 2SA2078G User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SA2078G  
Silicon PNP epitaxial planar type  
For general amplification  
Complementary to 2SC5846G  
Features  
Package  
Code  
SSSMini3-F2  
Marking Symbol: 7H  
Pin Name  
1. Base  
High forward current transfer ratio hFE  
SSS-Mini type package, allowing downsizing of the equipment  
and automatic insertion through the tape packing and the maga-  
zine packing.  
2. Emitter  
3. Collector  
Absolute Maximum Ratings Ta = 25°C  
Parameter  
Symbol  
Rating  
60  
Unit  
V
Collector-base voltage (Emitter open) VCBO  
Collector-emitter voltage (Base open) VCEO  
Emitter-base voltage (Collector open) VEBO  
50  
V
7  
V
Collector current  
IC  
ICP  
PC  
Tj  
100  
200  
100  
mA  
mA  
mW  
°C  
Peak collector current  
Collector power dissipation  
Junction temperature  
Storage temperature  
125  
Tstg  
55 to +125  
°C  
Electrical Characteristics Ta = 25°C 3°C  
Parameter  
Symbol  
VCBO  
VCEO  
VEBO  
ICBO  
Conditions  
Min  
60  
50  
7  
Typ  
Max  
Unit  
V
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector-base cutoff current (Emitter open)  
Collector-emitter cutoff current (Base open)  
Forward current transfer ratio  
IC = −10 µA, IE = 0  
IC = −100 µA, IB = 0  
IE = −10 µA, IC = 0  
VCB = −20 V, IE = 0  
VCE = −10 V, IB = 0  
VCE = −10 V, IC = −2 mA  
V
V
0.1  
100  
390  
µA  
µA  
ICEO  
hFE  
180  
Collector-emitter saturation voltage  
Transition frequency  
VCE(sat) IC = −100 mA, IB = −10 mA  
0.2 0.5  
V
fT  
VCB = −10 V, IE = 1 mA, f = 200 MHz  
VCB = −10 V, IE = 0, f = 1 MHz  
80  
MHz  
pF  
Collector output capacitance  
Cob  
2.2  
(Common base, input open circuited)  
Note) Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
Publication date: May 2007  
SJC00382AED  
1
 
This product complies with the RoHS Directive (EU 2002/95/EC).  
SSSMini3-F2  
Unit: mm  
1.20 0.05  
0.30 +00..0025  
3
2
1
0.13 +00..0025  
0.20 +00..0025  
(0.4)  
(0.4)  
0.80 0.05  
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Mr Coffee Coffeemaker FT Series User Manual
MTD Yard Vacuum 24677L User Manual
Nilfisk ALTO Water Heater PHH15002A User Manual
Nintendo Handheld Game System SPR 001 User Manual
Nostalgia Electrics Blender MSB 64 User Manual
Oki Printer ML184 User Manual
Omron Healthcare Blood Pressure Monitor 705IT User Manual
Optoma Technology Projector EP705H User Manual
Oricom Cordless Telephone BB100 User Manual
Oster Mixer FPSTSM5101 User Manual