Omega Engineering Clock Radio I 32 User Manual

Step 10. Enter to the Thermocouple Input Submenu  
Step 29. Enable Alarm 1 Submenu  
If flashing is displayed, press , if  
SPECIFICATION  
Press to store Thermocouple Input. The display will stop  
is displayed,  
d
ENBL  
a
DSBL  
Accuracy:  
+0.5°C temp;  
0.03% rdg. process typical  
Resolution:  
Output 1:  
flashing and show the top menu for Thermocouple types. If  
you press controller will step to next menu item (Skip to Step 14).  
a
press until  
is displayed, then press to store and  
b
ENBL  
d
Relay 250 Vac @ 3 A Resistive Load,  
SSR, Pulse  
go to the next menu item.  
Output 2:  
1
°
/0.1°; 10 µV process  
Relay 250 Vac @ 3 A Resistive Load,  
Step 11. Enter to the Thermocouple Type Input Submenu  
Step 30. Select the Deviation Control Type Submenu  
Temperature Stability:  
0.04°C/°C RTD;  
0.05°C/°C TC @ 25°C (77°F);  
50 ppm/°C process  
SSR, Pulse  
Press to display flashing, previously selected  
d
Only with -AL option  
Press . If flashing  
Deviation is displayed press  
,
d
_DEV  
a
Thermocouple type.  
otherwise press until flashing  
is shown. Now  
_DEV  
Options: Communication  
RS-232 / RS-485 or  
Excitation: 24 Vdc @ 25 mA  
Not available for Low Power Option  
Line Voltage/Power:  
90 - 240 Vac 10%, 50 - 400 Hz*,  
or 110 - 375 Vdc, 4 W  
* No CE compliance above 60 Hz  
Low Voltage Power Option:  
12 - 36 Vdc, 3 W**  
** Units can be powered safely with 24 Vac  
but No Certification for CE/UL are claimed.  
Dimensions:  
25.4 H x 48 W x 126.3 D mm  
(1.0 x 1.89 x 5")  
Weight:  
127 g (0.28 lb)  
b
press to store and go to next menu item.  
d
Step 12. Scroll through available selection of TC types  
Display:  
4-digits, 9-segments LED,  
10.2 mm (0.40") with red, green and  
amber programmable colors  
Input Types:  
Thermocouple, RTD, Analog Voltage  
and Current  
TC: (ITS90)  
J, K, T, E, R, S, B, C, N, L  
RTD: (ITS68)  
Press to sequence thru flashing Thermocouple types,  
b
Step 31. Select the Latched Type Submenu  
(select k -for type "K" CHROMEGA®/ALOMEGA®)  
Press . If flashing  
Unlatched is displayed press  
,
d
UNLT  
a
otherwise press until  
is displayed.  
b
UNLT  
J K T E N DIN J R S B C - TC types  
J k t E N dN J R S b C - Display  
Press to store and advance to next menu item.  
d
Step 32. Select the Normally Open Type of Contact  
Closure Submenu  
Step 13. Store TC type  
After you have selected the Thermocouple type press to  
d
Press . If flashing  
Normally Open is displayed,  
N.o.  
d
100/500/1000 ohm Pt sensor  
2-, 3-, or 4-wire; 0.00385 or 0.00392  
curve  
store your selection, the instrument automatically advances  
to the next menu item.  
press , otherwise press until  
is displayed. Press  
a
b
N.o.  
d
to store and advance to next menu item.  
Voltage:  
0 to 100 mV, 0 to 1 V, 0 to 10 Vdc  
Current:  
0 to 20 mA (4 to 20 mA)  
Approvals:  
UL, C-UL, CE per EN50081-1,  
EN50082-2, EN61010-1  
Step 14. Enter to Reading Configuration Menu  
Step 33. Select the Above Type of Active Submenu  
The display shows  
Reading Configuration, which is the  
RDG  
Press . If flashing  
Above is displayed, press  
,
a
d
ABoV  
top menu for 4 submenus: Decimal Point, Degree Units,  
Filter Constant and Input/Reading Submenus.  
otherwise press until  
is displayed. Press to store  
b
ABoV  
d
and advance to next menu item.  
WARNING: These products are not designed for use in, and should not be used for, patient-  
connected applications.  
Step 15. Enter to Decimal Point Submenu  
Step 34. Enable Alarm 1 at Power On (  
)
A.P.oN  
This device is marked with the international caution symbol. It is important to read the  
Setup Guide before installing or commissioning this device, as the guide contains important  
information relating to safety and EMC.  
Press to show  
d
Decimal Point.  
DEC  
Press . If flashing  
is displayed, press , otherwise  
d
ENBL  
a
i/32 Temperature & Process  
Monitor/Alarm  
press until  
is displayed. Press to store and  
b
ENBL  
d
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.  
OEMGA is constantly pursuing certification of its products to the European New Approach Directives.  
OMEGA will add the CE mark to every appropriate device upon certification.  
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.  
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.  
Step 16. Display the Decimal Point position  
Press again to display the flashing Decimal Point position.  
d
advance to next menu item.  
Step 35. Enter Alarm 1 High Submenu  
®
Step 17. Select the Decimal Point position  
Press twice to skip  
Alarm 1 Low value.  
is  
ALR.L  
a
ALR.L  
for above.  
TRADEMARK NOTICE:  
Press to select  
b
Decimal Point position.  
FFF.F  
for below &  
ALR.H  
®
®
®
®
,
omega.com  
,
, and  
are Trademarks of  
Step 18. Store selected Decimal Point position  
(
)
Step 36. Set the Alarm 1 High value  
ALR.H  
Press . Press or until value to set the display to  
OMEGA ENGINEERING, INC.  
By pressing momentarily the Decimal Point position will  
OMEGAnet® On-Line Service  
Internet e-mail  
d
d
b
c
be stored and the instrument will go to the next menu item.  
. Press to save.  
d
002.0  
Step 19. Enter to Temperature Unit Submenu  
Step 37. Enter the Alarm 2 Menu  
The display will show  
Display shows  
Temperature Unit.  
Servicing North America:  
TEMP  
WARRANTY/DISCLAIMER  
the top menu for Alarm 2.  
ALR2  
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of  
one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will  
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is  
returned to OMEGA.  
Repeat steps from 28 to 36 to set for Alarm 2 the same  
conditions as for Alarm 1.  
USA:VV  
ISO 9001 CertifiedV  
VV  
VV  
One Omega Drive, P.O. Box 4047  
Stamford CT 06907-0047  
TEL: (203) 359-1660VV  
Step 20. Display available Temperature Units  
Press to display the flashing Degree or  
.
°F °C  
d
FAX: (203) 359-7700  
FAX: (514) 856-6886  
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will  
issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA,  
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply  
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,  
operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit  
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive  
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating  
conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to  
contact points, fuses, and triacs.  
Step 38. Configuration of Display Color Selection  
Canada:VV  
976 Bergar  
Step 21. Scroll through Temperature Units selection  
Press to select Degree.  
Press until the  
Display Color Selection Menu  
COLR  
a
VV  
VV  
VV  
Laval (Quebec) H7L 5A1  
TEL: (514) 856-6928VV  
b
°F  
appears on the Display. Configure  
as  
/
COLR  
/
N.CLR GRN  
(amber). Please  
2.CLR AMBR  
(green),  
/
(red),  
1.CLR RED  
Step 22. Store the Temperature Unit  
refer to the operator’s manual if needed.  
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither  
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from  
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA  
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO  
OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED,  
EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION  
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with  
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or  
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event  
shall OMEGA be liable for consequential, incidental or special damages.  
For immediate technical or application assistance:  
Press to display momentarily that the Degree Unit has  
d
been stored and the instrument will go automatically to the  
next menu item.  
Step 39. Run a Test  
USA and Canada:V  
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA®  
Customer Service: 1-800-622-2378 / 1-800-622-BEST®  
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN®  
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA  
Press until reset the controller and return to RUN Mode  
a
VV  
VV  
EE  
to display  
(Ambient Temperature). Now you are  
075.0  
Step 23. Enter the Filter Constant Submenu  
ready to observe temperature as it rises 10°F higher than  
displayed. Touch the tip of the Thermocouple to raise the  
Mexico and V  
Latin American:E  
VV  
TEL: (001)800-TC-OMEGA®V  
En Español: (001) 203-359-7803V  
FAX: (001) 203-359-7807  
Display shows  
Filter Constant Submenu.  
FLTR  
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as  
a
“Basic  
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications  
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,  
used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic  
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless  
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.  
temperature above the Alarm 2 High value  
, and AL2  
082.0  
Step 24. Display the Filter Constant Value Submenu  
will turn on, and Display Color will change from Green to  
Amber. Continue touching the tip to raise the temperature  
Press to display the flashing, previously selected Filter  
Servicing Europe:  
d
Constant.  
above the Alarm 1 High value  
change from Amber to Red.  
and Display Color will  
087.0  
RETURN REQUESTS/INQUIRIES  
Benelux:VV  
Postbus 8034, 1180 LA Amstelveen, The Netherlands  
TEL: +31 20 3472121VV FAX: +31 20 6434643  
Toll Free in Benelux: 0800 0993344V  
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE  
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)  
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING  
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any  
correspondence.  
VV  
VV  
VV  
Step 25. Scroll through available Filter Constants  
Press to sequence thru Filter Constants  
,
0001 0002  
.
0128  
,
b
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in  
transit.  
Czech Republic:V  
VV  
VV  
Rudé armády 1868, 733 01 Karviná 8  
TEL: +420 69 6311899V FAX: +420 69 6311114  
,
0004 0008 0016 0032 0064  
,
,
,
and  
FOR WARRANTY RETURNS, please have the  
following information available BEFORE  
contacting OMEGA:  
FOR NON-WARRANTY REPAIRS, consult OMEGA for  
current repair charges. Have the following information  
available BEFORE contacting OMEGA:  
Step 26. Store the Filter Constant  
France:VV  
VV  
VV  
9, rue Denis Papin, 78190 Trappes  
TEL: +33 130 621 400V FAX: +33 130 699 120  
Toll Free in France: 0800406342  
1. Purchase Order number under which the product  
was PURCHASED,  
1. Purchase Order number to cover the COST of the  
repair,  
Press momentarily to store  
Filter Constant and the  
0004  
d
instrument will automatically go to the next menu item.  
2. Model and serial number of the product under  
warranty, and  
3. Repair instructions and/or specific problems  
relative to the product.  
2. Model and serial number of product, and  
3. Repair instructions and/or specific problems  
relative to the product.  
VV  
Step 27. Enter Alarm 1 Menu  
Germany/Austria:V  
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany  
TEL: +49 7056 9398-0V FAX: +49 7056 9398-29  
Toll Free in Germany: 0800 639 7678  
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords  
our customers the latest in technology and engineering.  
VV  
VV  
VV  
The display will show  
the top menu for Alarm 1. In the  
ALR1  
following steps we are going to enable Alarm 1, Deviation,  
Unlatch, Normally Open, Active Above, Enable at power on  
and +2°F High Alarm i.e. Process Value > Setpoint 1 Value  
+2°F will activate Alarm 1.  
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.  
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,  
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without  
the prior written consent of OMEGA ENGINEERING, INC.  
United Kingdom:V  
ISO 9002 CertifiedV  
VV  
VV  
VV  
VV  
One Omega Drive  
River Bend Technology Centre  
Northbank, Irlam Manchester M44 5BD United Kingdom  
TEL: +44 161 777 6611V FAX: +44 161 777 6622  
Toll Free in England: 0800 488 488  
PATENT AND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.  
No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE  
41 34398 C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET NO. 91  
12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S.  
and International Patents pending or applied for.  
Step 28. Enter Alarm 1 Enable/Disable Submenu  
Press to display flashing  
d
/
DSBL ENBL  
.
MQS3448/0102  
 

Multiquip Portable Generator GA 6RE User Manual
NETGEAR Modem RM356 User Manual
NeumannBerlin Microcassette Recorder TLM 127 User Manual
NHT Speaker Evolution System User Manual
Nilfisk ALTO Carpet Cleaner STEAMTEC 5 IH User Manual
Nostalgia Electrics Frozen Dessert Maker DFIM SERIES User Manual
OWI Portable Speaker P8378P User Manual
Panasonic Air Conditioner CS E12DKRW User Manual
Panasonic Camcorder AJ D400P User Manual
Panasonic Network Card 2SA2161G User Manual