NETGEAR Switch FS2105 User Manual

 
Network Ports  
Ports 1 through 4 for the Model FS2105 Fast Ethernet Switch and ports 1 through 7 for  
the Model FS2108 Fast Ethernet Switch are permanently configured for normal wiring  
for connection to a PC or a router. They are all 10/100 Mbps ports.  
Normal/Uplink Ports  
There are two port 5s for the Model FS2105 Fast Ethernet Switch and two port 8s for  
the Model FS2108 Fast Ethernet Switch. These ports are used as follows:  
Port 5 Normal (or port 8 Normal) is for normal (MDI-X) wiring for direct  
connection to a PC or router.  
Port 5 Uplink (or port 8 Uplink) is for uplink (MDI) wiring for connection  
to a hub or a switch.  
Note: Port 5 Normal (or port 8 Normal) and port 5 Uplink (or port 8 Uplink) can  
have only one connection at a time. If both ports are connected at the same time, they  
become disabled.  
Applications  
PC Workgroup  
Both the Model FS2105 Fast Ethernet Switch and the Model FS2108 Fast Ethernet Switch  
can be used as a desktop switch to build a small network that enables users to  
have 100 Mbps access to a file server. Compared with a hub, where the network  
bandwidth is shared among all users, the Model FS2105 switch or the Model FS2108  
switch provides dedicated 10 or 100 Mbps bandwidth to each PC.  
Key  
100 Mbps  
10 Mbps  
Model FS2108  
Switch  
110V 3A MAX  
Up-link  
8
7
6
5
4
3
2
1
PWR  
9610FA  
With a full-duplex adapter card installed in the server, a 200 Mbps connection is  
possible on the port where the server or PC is connected.  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
Expanded Workgroup  
Both the Model FS2105 Fast Ethernet Switch and the Model FS2108 Fast Ethernet Switch  
can be used to connect multiple PC workgroups.  
Model FS2108 Switch  
110V 3A MAX  
Uplink  
8
7
6
5
4
3
2
1
PWR  
Uplink  
Uplink  
Model EN2005  
10 Mbps Hub  
Model DS108  
10/100 Mbps Hub  
Auto 10/100 MbpsDUAL SPEED  
7.5 1A  
Up-link  
5
4
3
2
1
PWR  
9609FA  
Installing the Switch  
There are three ways to install either the Model FS2105 Fast Ethernet Switch or the Model  
FS2108 Fast Ethernet Switch:  
Desktop  
Magnetic mount (see “Inserting the Magnet”)  
Wall mount  
You do not need tools for desktop or magnetic mount installation, but you do need a Phillips  
screwdriver for wall mount installation.  
Wall Mounting the Switch  
1. Measure the distance between the mounting holes on the back of the  
switch.  
2. Mark the wall to match the location of the mounting holes.  
3. At the marked location, insert the two screws that you received in your  
package contents.  
Note: For all three installations:  
Choose a location that is near the devices to be connected.  
Make sure you are close to an electrical outlet.  
Be sure to leave at least 2 inches of space all around the switch for  
ventilation.  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
Magnet Mounting the Switch  
Inserting the Magnet  
1
2
9640FA  
Removing the Magnet  
2
1
9641FA  
Connecting the Network  
To connect devices to the switch:  
1. Connect the devices to the 10/100 Mbps ports on the switch, using  
category 5 UTP cable with an RJ-45 plug.  
Note: Ethernet specifications limit the total cable length between  
your PC and the switch to 328 feet (100 meters).  
2. Connect the switch for specific devices:  
To connect to a PC or router, use port 5 Normal (or port 8 Normal). This  
connection is considered “normal.”  
To connect to a hub or another switch, use port 5 Uplink (or port 8  
Uplink). This connection is considered “uplink.”  
3. Connect one end of the DC power adapter cable to the power outlet on  
the rear panel of the switch and the other end of the power adapter  
cable to the wall outlet. Verifying  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
 
Verifying Installation  
When power has been applied to the switch:  
The green Pwr (power) LED on the front panel is on.  
The green Link/Activity LED on each connected port is on.  
When the switch is connected and operating, refer to the table in “LEDs” for  
information about the LEDs and their activity.  
Troubleshooting Information  
Symptom  
Cause  
Solution  
Green 100M  
LED is off.  
Port is  
Make sure that the adapter card is capable of and set  
for 100 Mbps operation.  
operating  
in 10 Mbps  
mode.  
Green Link LED Port is  
is on and Green operating in  
FDX LED is off half-duplex  
Make sure that the connected device is capable of  
full-duplex transmission, using autosensing. The  
Model FS2105 switch and the Model FS2108 switch  
will not support a full-duplex link that is not using  
autosensing.  
when  
mode.  
connected to a  
full-duplex  
network.  
Link is off on  
port 5 (or 8).  
Port 5 (or 8) is Make sure that only one port 5 (or 8) is connected,  
not connected not both (Uplink or Normal).  
correctly.  
Normal port 5 (or 8) is connected to a PC or router.  
Uplink port 5 (or 8) is connected to a hub or switch.  
Make sure that you are using standard, Category 5,  
straight-through UTP cabling.  
Link/Activity  
Port  
Make sure that the attached device is powered and  
there is a proper UTP connection.  
LED is off on a connection  
connected port. is not  
functioning.  
Make sure that the network adapter  
card installed in the PC is working.  
Verify that the network adapter card  
is operating at the proper speed  
(10 Mbps or 100 Mbps).  
Make sure that the proper cable is installed. Check  
for miswired cable pairs or loose connectors.  
For 100 Mbps operation, only Category 5 or better  
grade cable should be used. For 10 Mbps operation,  
Category 3 cable can be used.  
Make sure that the length of the UTP cable from the  
switch to the device does not exceed 328 feet (100  
meters).  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
Technical Specifications  
Type  
Specification  
Standards  
IEEC 802-3, 10BASE-T Ethernet  
Compatibility  
IEEC 802-3u, 100BASE-T Ethernet  
IEEE 802.3x Flow control; back-pressure support  
Compatible with major network software, including Windows ,  
NetWare, Mac OS, and Linux  
®
Network Interface  
Power  
RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet  
interface  
Model FS2105 switch: 5.5 w max.  
Model FS2108 switch: 8.0 w max.  
Physical Specifications  
Dimensions:  
Weight:  
177 x 118 x 32 mm (for both switches)  
1.25 lb; 0.6 kg  
Electromagnetic  
Compliance  
Warranty  
CE mark, commercial; FCC Part 15 Class A; EN 55 022 (CISPR  
22), Class A; VCCI Class A; and C-Tick  
Switch:  
Power Adapter:  
Limited lifetime warranty  
5 years  
For more information about customer support and technical specifications, refer  
to the NETGEAR Web site:  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
© 1999 by NETGEAR, Inc. All rights reserved.  
Trademarks  
NETGEAR is a trademark of NETGEAR, Inc.  
Microsoft and Windows are registered trademarks of Microsoft Corporation.  
All other trademarks and registered trademarks are the property of their respective owners.  
Statement of Conditions  
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the  
right to make changes to the product described in this document without notice.  
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described  
herein.  
Certificate of the Manufacturer/Importer  
It is hereby certified that the NETGEAR Model FS2105 Fast Ethernet Switch and Model FS2108 Fast  
Ethernet Switch have been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/  
1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with  
the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating  
instructions.  
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the  
market and has been granted the right to test the series for compliance with the regulations.  
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency  
Notice  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  
This device may not cause harmful interference.  
This device must accept any interference received, including interference that may cause undesired  
operation.  
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
EN 55 022 Declaration of Conformance  
This is to certify that the NETGEAR Model FS2105 Fast Ethernet Switch and Model FS2108 Fast Ethernet  
Switch are shielded against the generation of radio interference in accordance with the application of Council  
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR  
22).  
Canadian Department of Communications Radio Interference Regulations  
This digital apparatus (NETGEAR Model FS2105 Fast Ethernet Switch and Model FS2108 Fast Ethernet  
Switch) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the  
Radio Interference Regulations of the Canadian Department of Communications.  
Règlement sur le brouillage radioélectrique du ministère des Communications  
Cet appareil numérique (NETGEAR Model FS2105 Fast Ethernet Switch et Model FS2108 Fast Ethernet  
Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites  
dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.  
Model FS2105/FS2108 Fast Ethernet Switch Installation Guide  
 
NETGEAR, Inc.  
A Bay Networks Company  
4401 Great America Parkway  
Santa Clara, CA 95054 USA  
Phone: 888-NETGEAR  
*M-FS2100NA-0*  
 

Miele Clothes Dryer T7944C User Manual
Miele Ventilation Hood da 186 User Manual
National Instruments Car Stereo System 320571 01 User Manual
NETGEAR Network Router EX3700 User Manual
Nextar Speaker NXBT 001 User Manual
NextBase Portable DVD Player SDV27 SD User Manual
Niles Audio Stereo System ZR 4 User Manual
Panasonic Answering Machine KX TS560ML User Manual
Panasonic Automobile Accessories CY RC50KN User Manual
ParaBody Home Gym 866101 User Manual