Patton electronic Network Router 07MOS10xx QS User Manual

OnSite 1052 & 1063 Series  
Metro-Optical Transport Access  
Nodes  
Quick Start Guide  
Sales Office: +1 (301) 975-1000  
Part Number: 07MOS10xx-QS, Rev. A  
Revised: November 19, 2009  
Technical Support: +1 (301) 975-1007  
 
3.0 Accessing and Configuring the System  
To access the system management functions for the first time, your may use either the SERIAL or the Ethernet  
LAN management port. Refer to the Installation and Operation Guide for access through the SERIAL port.  
For first time access through the Ethernet LAN management port, follow these steps:  
1. Connect a PC to the Ethernet LAN management port using the RJ-45 connector.  
2. Configure the PC to connect to the OS-10 Series system using the factory default settings for the Ethernet  
LAN management port.  
Note By default, the IP address is set to 192.168.2.100.  
3. Launch the Web browser of your choice, and type the default IP address of the system in the Address field  
of the browser.  
4. Log in to the OS-10 Series system using the super user ID and password.  
Note The factory-assigned default password for the Super user is super (all lowercase letters).  
Once you gain access to the system using the default settings, change the IP settings for the LAN port for secure  
access to the system.  
3.1 Changing the IP Settings for the LAN port  
To configure the Ethernet LAN management port settings, follow these steps:  
1. Select the SYSTEM folder from the OnSight Device Manager (DM) web-based GUI navigation menu.  
2. From the expanded SYSTEM folder, select Management Access, and from this folder select LAN.  
3. On the Ethernet LAN Management Port page, type the new LAN IP Address.  
Note The Admin Status for the Ethernet LAN management port is always enabled.  
4. Click on Apply.  
The new IP settings take effect once you click on the Apply button. This change in settings causes the loss of  
access connectivity to the system. You can regain access immediately by typing the new IP address of the LAN  
port in the Address field of the browser. (Make sure that you change your PC settings to allow connectivity to the  
OS-10 Series system over the same IP subnetwork.)  
You will need to save the system configuration to avoid losing the new IP settings after a subsequent reboot.  
Note The system uses the last saved configuration to restore system operation and traffic connectivity after  
the completion of the reboot. Any recent configuration data and connections not saved to the system  
configuration file are lost and need re-entry, if required.  
OnSite Series Quick Start Guide  
3
 
3.2 Saving the System Configuration  
To save the system configuration to the flash memory, follow these steps:  
1. Select the SYSTEM folder from the OnSight DM web-based GUI navigation menu.  
2. From the expanded SYSTEM folder, select the Actions folder.  
3. From the expanded Actions folder, select Save Configuration.  
A warning window opens to alert you to the start of the save-configuration process. Click on OK to continue or  
Cancel to cancel the request.  
4.0 Additional Information  
The system is now ready for operation using the OnSight DM web-based graphical user interface (GUI). You may  
now configure the system clock, timing mode and STM-1 interface settings for your intended application.  
Refer to the OnSite Series Getting Started Guide and the OnSite Series Administrator’s Reference Guide located on the  
CD-ROM shipped with your device.  
A.0 Customer and Technical Support  
Online support: www.patton.com  
E-mail support: [email protected]—answered within 1 business day  
Telephone support:  
Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to  
2200 UTC/GMT)  
Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800  
UTC/GMT)  
Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)  
Copyright statement  
Copyright © 2009, Patton Electronics Company. All rights reserved.  
The information in this document is subject to change without notice. Patton Electronics assumes no  
liability for errors that may appear in this document.  
In accordance with the requirements of council directive 2002/96/EC on Waste of  
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate  
this product from other waste and scrap and deliver to the WEEE collection system in  
your country for recycling.  
4
OnSite Series Quick Start Guide  
 

MTD Edger 520 550 551 554 User Manual
Mustek Computer Monitor LM 3000 User Manual
Napoleon Grills Gas Grill PT750RSB User Manual
NEC Computer Hardware PD789488 User Manual
NEC Projector MultiSync MT840 User Manual
Nissan Automobile 4083 User Manual
Nortel Networks Telephone CallPilot Desktop Messaging User Manual
Palsonic Stereo System PMSL 329 User Manual
Panasonic Cell Phone kx t7030 User Manual
Patton electronic Network Card Model 1065 User Manual