USER
MANUAL
MODEL 2015
Interface Powered
RS-449/422 to V.35
Converter
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
Part# 07M2015-C
Doc# 070020UC
Revised 12/31/96
2.0 GENERAL INFORMATION
3.0 INSTALLATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions arise during
installation or use of the unit, contact Patton Electronics Technical
The Patton Model 2015 is very simple to install. Just plug it in like
a normal cable and you're ready to go: no configuration is necessary!
Since the Model 2015 is available in various combinations of genders
and DCE/DTE orientations, many applications are possible. Figures 1
and 2 show two possible applications for the Model 2015.
V.35 Modem
RS-449/422 DTE
2.1 FEATURES
• Bidirectionally converts synchronous RS-449/422 to V.35
• Data rates to 2 Mbps, full or half duplex
• Transparent to protocol
Figure 1. A common RS-449/422 DTE to V.35 DCE installation
• No AC power or batteries required
• Various DCE/DTE combinations available
• DB-37 and M/34 connectors with integral 6 foot cable
• Circuitry housed in a miniature case
• Made in the USA
V.35 Mini Computer
RS-449/422 DCE
Figure 2. A common V.35 DTE to RS-449/422 DCE installation.
2.2 DESCRIPTION
The Model 2015 RS-449/422 to V.35 converter lets a
synchronous RS-449/422 device communicate bi-directionally with a
synchronous V.35 device. The Model 2015 requires no AC power or
batteries to operate and supports data rates to 2 Mbps. Operating full
or half duplex, the Model 2015 passes all necessary clocking and
control signals, and is transparent to protocol.
The Patton Model 2015 connects directly to the synchronous
RS-449/422 interface using a male or female DB-37 connector. A male
or female M/34 connector at the end of an integral 6 foot cable plugs
into the V.35 device. Models with any combination of "DCE" and "DTE"
wiring are available, thus eliminating the need for special crossover
cables.
Housed in an ultra-miniature case measuring only 2.66" x 2.10" x
0.73", the Model 2015 fits easily into tight locations. Like all Patton
products, the Model 2015 is manufactured by Patton Electronics in the
USA.
3
4
APPENDIX A
APPENDIX B
PATTON MODEL 2015 SPECIFICATIONS
PATTON MODEL 2015 DTE/DCE BLOCK DIAGRAM
Interfaces:
EIA RS-449/422/CCITT V.24 to CCITT V.35
0 - 2 Mbps
Data Rates:
Transmission Mode: Full or half duplex
Protocol:
Transparent to protocol
Clocking:
Connectors:
Set by connected devices
DB-37 male or female on RS-449/422 side,
M/34 male or female on V.35 side
Power Supply:
No external power required; uses power
from NIC data and control signals
Temperature Range: 0-60°C (32-140°F)
Altitude:
0-15,000 feet
Humidity:
Dimensions:
Weight:
5 to 95% non-condensing
2.66"L x 2.10"H x 0.73"W
14 oz, including cable and connectors
Applies to Models
2015MC-FT
2015MC-MT
2015FC-MT
2015FC-FT
5
6
APPENDIX C
APPENDIX D
PATTON MODEL 2015 DCE/DTE BLOCK DIAGRAM
PATTON MODEL 2015 INTERFACE PIN ASSIGNMENTS
DB-37 Connector (RS-449 DCE or DTE)
Pin #
1
Signal
Shield
4
TD
5
TC
6
RD
7
RTS
8
RC
9
CTS
11
12
13
17
19
20
22
23
24
25
26
27
29
30
31
35
37
DM (DSR)
TR (DTR)
RR (CD)
TT (XTC)
Signal Ground
Signal Ground
TD/
TC/
RD/
RTS/
RC/
CTS/
DM/ (DSR/)
TR/ (DTR/)
RR/ (CD/)
TT/ (XTC/)
Signal Ground
Applies to Models
2015MT-FC
2015MT-MT
2015FT-MC
2015FT-FC
7
8
APPENDIX D (Continued)
PATTON MODEL 2015 M34 PIN ASSIGNMENTS
M/34 Connector (V.35 DCE or DTE)
Pin #
A
Signal
Shield
B
SGND (Signal Ground)
C
D
E
F
RTS
CTS
DSR
CD
H
P
DTR
TD
R
RD
S
T
U
V
TD/
RD/
XTC
RC
W
Y
XTC/
TC
AA
TC/
9
|