Partner Tech Trimmer PWT420 User Manual

LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as  
manufactured is free from defects in materials and workmanship. For a period of  
two (2) years from date of purchase by the original consumer purchaser, we will re-  
pair or replace, at our option, without charge for parts or labor incurred in replacing  
parts, any part which we find to be defective due to materials or workmanship. This  
Warranty is subject to the following limitations and exclusions.  
1. This warranty does not apply to the engine. Please refer to the applicable  
manufacturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or at-  
tachment are the responsibility of the purchaser. Transportation charges for any  
parts submitted for replacement under this warranty must be paid by the pur-  
chaser unless such return is requested by the manufacturer.  
3. The Warranty period for any products used for rental or commercial purposes is  
limited to 45 days from the date of original purchase.  
4. This Warranty applies only to products which have been properly assembled,  
adjusted, operated, and maintained in accordance with the instructions furnished.  
This Warranty does not apply to any product which has been subjected to altera-  
tion, misuse, abuse, improper assembly or installation, delivery damage, or to  
normal wear of the product.  
5. Exclusions: Excluded from this Warranty are belts, rotating lines, rotating line  
adapters, normal wear, normal adjustments, standard hardware and normal  
maintenance.  
6. In the event you have a claim under this Warranty, you must return the product to  
an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty,  
please contact:  
In Canada contact:  
HOP  
HOP  
Customer Service Department  
1030 Stevens Creek Road  
Augusta, GA 30907 USA  
Customer Service Department  
5855 Terry Fox Way  
Mississauga, Ontario L5V 3E4  
REPAIR PARTS MANUAL  
MODEL NUMBER PWT420  
(MFG. ID. NO. 96171000203)  
Wheeled Weed Trimmer  
giving the model number, serial number and date of purchase of your product and  
the name and address of the authorized dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL  
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME  
TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES.  
Some areas do not allow the limitation of consequential damages or limitations  
of how long an implied Warranty may last, so the above limitations or exclusions  
may not apply to you. This Warranty gives you specific legal rights, and you may  
have other rights which vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Mag-  
nuson-Moss Act of 1975.  
532 41 86-35 12.06.07 BY  
Printed in U.S.A.  
 
WEED TRIMMER - MODEL NUMBER PWT420 (96171000203)  
SERVICE NOTES  
PRODUCT NUMBER 961 71 00-02  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
- - -  
Engine, Briggs & Stratton,  
Model Number 126T02  
(Order parts from Engine Manufacturer)  
Bolt, Engine Mounting 3/8-16  
Pulley, Engine (Includes Setscrew, Key #4)  
Handle, Lower  
2
3
8
9
532 15 04-06  
532 17 94-66  
532 18 67-54  
532 15 00-78  
Screw, Hex Washer Head 5/16-18 x .75  
Handle, Upper  
10 532 18 67-55  
11 532 17 09-80  
12 532 19 19-38  
15 532 17 97-51  
16 532 19 47-88  
18 532 06 64-26  
19 532 17 69-83  
20 532 41 72-38  
21 532 15 87-55  
22 532 18 67-56  
23 532 15 00-78  
24 532 05 21-60  
26 532 17 02-58  
27 532 40 91-48  
28 532 18 16-99  
30 532 41 25-05  
33 532 13 20-04  
34 532 12 52-03  
35 532 75 06-34  
36 532 85 10-84  
37 532 85 02-63  
38 532 85 10-74  
- - 532 18 74-78  
- - 532 18 74-79  
- - 532 41 86-35  
Bolt, Handle  
Knob, Handle  
Handle Adjuster Assembly  
Guide, Rope  
Wire Tire  
Control Bar  
Throttle Control  
Screw, Hex Washer Head  
Axle Shaft Assembly  
Screw, Hex Washer Head 5/16-18 x .75  
Washer, Axle  
Wheel, 14 x 2  
Hex Flange Locknut 3/8-16  
Drive Control Cable  
Decal, Engine Cover  
Nut  
Bracket, Upstop  
Screw, Thd. Roll. #10-24 x 5/8  
Screw, Hex Head 3/8-24 x 1  
Washer, Lock  
Washer, Flat, Hardened  
Operator’s Manual, European  
Operator's Manual, Scandanivan  
Repair Parts Manual, English  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be  
hazardous, damage your weed trimmer and void your warranty.  
6
3
 
WEED TRIMMER - MODEL NUMBER PWT420 (96171000203)  
WEED TRIMMER - MODEL NUMBER PWT420 (96171000203)  
PRODUCT NUMBER 961 71 00-02  
PRODUCT NUMBER 961 71 00-02  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
532 18 67-60  
532 18 22-19  
532 17 37-15  
532 18 54-76  
532 18 67-51  
532 16 60-42  
532 17 37-16  
532 75 15-92  
532 16 60-43  
Chassis Assembly  
51  
52  
20 44 47 21  
Line, Trimmer .155 diameter x 18.75 long  
Screw, Self-Tapping 5/16-18 x 1  
V-Belt  
14  
43  
Bracket, Idler  
Pulley, Idler, V-Groove  
Bolt, Hex Head 3/8-16 x 1.25  
Locknut, Hex 3/8-16  
Pulley, Idler, Flat  
10 532 16 08-29  
11 532 15 55-52  
12 532 17 37-17  
13 532 17 47-19  
14 532 40 91-49  
15 532 17 38-11  
16 532 18 02-68  
17 532 05 78-08  
18 532 17 88-48  
19 532 19 95-74  
20 532 17 83-90  
21 532 14 97-46  
22 873 61 06-00  
23 532 85 02-63  
24 819 12 12-14  
25 532 18 03-40  
26 532 17 25-51  
27 532 17 45-49  
28 532 17 25-20  
29 532 18 67-52  
30 532 17 45-43  
31 532 17 45-81  
32 532 17 39-73  
33 532 17 25-19  
34 532 18 03-38  
35 532 18 22-17  
36 532 17 25-16  
37 532 17 45-80  
38 532 17 25-23  
39 532 18 03-34  
40 532 18 03-33  
41 532 17 40-29  
42 532 18 74-58  
43 532 17 40-42  
44 532 18 66-00  
45 532 18 67-53  
46 817 06 04-08  
47 532 18 22-05  
51 532 18 90-06  
52 532 17 88-48  
Bolt, Shoulder  
Locknut 5/16-18  
Spacer  
Bolt, Shoulder  
Locknut, Flange  
Spring, Return  
Deflector, Bottom  
Screw 1/4-20 x 1/2  
Screw #10-24 x 3/4  
Belt Keeper  
Cover, Chassis, Top  
Screw #10-24 x 1-3/4  
Nut, Hex 3/8-24 UNF  
Washer, Lock 3/8  
Washer, Flat 3/8  
Pulley, Driven  
Spacer, Pulley  
Bearing  
1
22  
23  
24  
17  
15  
8
12  
5
41  
6
45  
7
10  
25  
11  
9
19  
26  
27*  
40  
4
28  
Jackshaft  
13  
Cover, Chassis, Bottom  
Spindle Housing Assembly (* Includes Upper Bearing, Key No. 27)  
Ring, Retaining, External, 17mm  
Spring, Locking Plate  
Locking Plate  
Carrier Plate Assembly  
Mow Ball Assembly (Includes Key Numbers 27, 37 and 38)  
Cover, Bearing  
Ring, Retaining, Internal, 40mm  
Mow Ball  
Bolt, Mow Ball  
Spindle Assembly, Complete (Includes Key No. 22-28 and 30-39)  
Spacer  
Decal, Safety  
29  
16  
30*  
18  
27  
31  
33  
3
32  
Decal, Instruction  
34  
Decal, Chassis Cover  
Belt Keeper, Bottom  
Screw, Self-Tapping  
Decal, Instruction  
Deflector, Rear  
Screw  
37  
27  
38  
36  
35  
46  
2
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be  
hazardous, damage your weed trimmer and void your warranty.  
39  
4
5
 

Miele Dishwasher 10014080 User Manual
Miele Refrigerator KF1801SF User Manual
Miele Refrigerator KFN 14943 SD ed User Manual
Milwaukee Grinder 58 01 0026 User Manual
Munchkin Baby Carrier Cargo Sling User Manual
Murphy Switch W0162 User Manual
National Instruments Computer Hardware 320174B 01 User Manual
Nilfisk ALTO Stereo Equalizer AMX 140FX User Manual
Optoma Technology Projector EP723 User Manual
Orion Car Audio Car Amplifier HCCA10002 User Manual