Paradyne Network Card MUM200 2 User Manual

Installation Instructions  
MUM200-2  
IP DSLAM Multiplexer Module with Dual Uplink Interface Capacity  
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when  
handling this equipment.  
CAUTION  
1.0 INSTALLATION  
1.1 Unpack and Inspect the Multiplexer Uplink Module (MUM)  
If there is visible damage, do not attempt to install the MUM200-2; contact Customer Support at 1-  
877-638-2638 (001-603-427-0600 for international customers) or [email protected].  
1.2 Install an Uplink Interface Module (UIM) on the MUM200-2  
A UIM provides the upstream network connection, via the MUM200-2, for Net to Net Technologies' IP  
DSLAMs; neither an IP DSLAM nor a MUM200-2 can function without a UIM. Any of Net to Net's  
available UIM models, with the exception of the UIM-1000T and UIM-1000F, may be installed on a  
MUM200-2 .  
z
Select a port on the MUM200-2 for UIM installation; either port (1 or 2) may be used. Although  
not required for operational purposes, if redundancy is desired two UIMs may be installed on a  
MUM200-2, one in each port.  
z
Remove the blanking plate from the selected port.  
Blanking plates should be stored for possible future use: if a UIM is removed from a  
MUM200-2, it must be replaced with either another UIM or a blanking plate. DO NOT  
OPERATE A MUM200-2 WITH AN OPEN UIM PORT.  
CAUTION  
z
Carefully slide the faceplate of the UIM under the lip of the MUM200-2 faceplate at the  
selected port opening such that the UIM circuit board is facedown and the label shows through  
the MUM200-2 port opening with the UIM model name along the right-hand edge.  
z
Ensure that the mounting holes on the UIM are lined up with the corresponding pems on the  
MUM200-2 circuit board and that the board-to-board connector key pins are properly aligned.  
z
Gently press down with even pressure on all four corners of the UIM until the board-to-board  
connector is fully seated.  
z
Secure the UIM circuit board to the MUM200-2 circuit board, at the pems, with the (4)  
provided panhead screws.  
 
220-0000069 rev 04  
Verify the connection: the Lnk (link) LED on the UIM-DS3 and UIM-E3 faceplate will flash green  
to indicate a network connection has been established.  
For further information refer to the Installation Instructions for each individual UIM model.  
2.0 IP DSLAM MANAGEMENT  
The MUM200-2 provides IP DSLAM management capability via Net to Net's web-based Network  
Management System (NMS) and a scaled-down version of Simple Network Management Protocol (SNMP).  
For access and configuration instructions, refer to Net to Net's NMS Management User Guide.  
3.0 ADDITIONAL INFORMATION  
3.1 LED Indications  
LED  
State  
Indication  
Additional Information  
PWR  
(Power)  
solid green  
MUM200-2 is receiving  
power  
Both IP DSLAM power terminals are connected.  
solid amber MUM200-2 is receiving  
power  
One of the two IP DSLAM power terminals are  
connected.  
no  
no power  
The MUM200-2 is not receiving power (the IP  
DSLAM may not be receiving power either).  
illumination  
Fan  
no  
all fans are functioning  
All four of the fans on the IP DSLAM fan card are  
functioning.  
illumination  
solid amber non-functioning fan  
One or more of the four fans on the IP DSLAM fan  
card are no longer functioning.  
Lnk (Link) solid green  
direct Ethernet  
The Lnk LED applies only to direct physical  
management connection is connections with the MGMT port; it does not  
established  
apply to uplink network connections.  
The MGMT Ethernet port runs at 10 Mbps and  
Half Duplex.  
no  
no direct connection via  
illumination the MGMT port is  
established  
UIM Lnk  
(Link)  
solid green  
UIM-10/100 Ethernet  
uplink connection is  
established  
For further information regarding UIM-10/100  
LEDs, please refer to the corresponding UIM  
Installation Instructions.  
flashing  
green  
UIM-T1/E1 or UIM-DS3/E3 For further information regarding UIM-T1/E1 or  
uplink connection is  
established  
UIM-DS3/E3 LEDs, please refer to the  
corresponding UIM Installation Instructions.  
no  
no uplink connection is  
Applicable to all UIM models types.  
illumination established  
 
220-0000069 rev 04  
3.2 Regulatory Compliance for Class A Equipment  
The following regulatory compliance information applies to a MUM200-2 as installed in one of Net to  
Net Technologies' IP DSLAMs.  
3.2.1 US Federal Communications Commission (FCC)  
Note: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is  
likely to cause harmful interference in which case the user will be required to correct the  
interference at his own expense.  
Caution: Changes or modifications not expressly approved by the manufacturer could void the  
user’s authority to operate the equipment.  
3.2.2 Industry Canada  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.  
3.2.3 Europe  
This Class A product complies with European Norm EN55022.  
Warning: In a domestic environment this product may cause radio interference in which case  
the user may be required to take adequate measures to correct the situation.  
220-0000069 rev04  
© Copyright 2002 Net to Net Technologies, Inc.  
™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc.  
Worldwide Headquarters  
Net to Net Technologies  
112 Corporate Drive  
Portsmouth, NH 03801  
USA  
EMEA Headquarters  
Net to Net Technologies  
Victoria House 19 Park Way  
Newbury Berkshire RG14 1EE  
UK  
+1 877-638-2638  
+44 (0) 1635 570950  
 
220-0000069 rev 04  

Milan Technology Network Card CCSF30XX 100 User Manual
MSi Computer Hardware MS 6775 v1x User Manual
National Instruments Impact Driver MID 7654 User Manual
Oki All in One Printer 4545 MFP User Manual
Omnimount Indoor Furnishings OM10020 User Manual
Orion Car Audio Speaker CO104S User Manual
Ozaki Worldwide Speaker EM985 User Manual
Panasonic Camcorder AG DVC 200E User Manual
Panasonic Car Video System CQE15EUC User Manual
ParaBody Home Gym 887101 User Manual