Paradyne Network Card 8820 S2 900 User Manual

Replacement Fan Tray Assembly for the  
8820 Broadband Access Concentrator  
Model 8820-S2-900  
Installation Instructions  
Document Number 8820-A2-GZ44-10  
June 2004  
What is the Fan Tray Assembly?  
The fan tray assembly is a dedicated cooling device installed in the chassis of the  
8820 Broadband Access Concentrator (BAC) to provide forced-air cooling of the  
chassis. The fans, located at the top of the BAC chassis, draw cooling air  
upwards from the bottom of the chassis, through the circuit cards or card cage,  
forcing the air out the opening, located at the top rear of the chassis.  
The fan tray assembly consists of six fans, a metal bracket, and a printed wiring  
board (PWB) with a press-fit connector and five status LEDs. Each fan provides a  
sense wire that indicates the status of the fan. The sense wires are connected to  
the backplane via the fan tray’s PWB and its connector.  
The rated airflow is 900 cfm (based on 6 fans at 150 cfm each) at zero back  
pressure.  
The fan tray is powered by 48 VDC from the backplane of the 8820 BAC.  
Nominal power consumption is less than 100 watts, depending upon the  
manufacturer.  
An LED is on the fan tray so that if a fan failure occurs, a signal is sent to the  
SCP card or MCP card and the yellow Fan ALARM LED on the chassis lights.  
Removal of the fan tray also causes the SCP card or MCP card to sense an  
alarm.  
The fan tray assembly weighs 10 lbs (22 kg). It is secured in place by two  
fan-locking brackets located on the right and left front of the assembly.  
8820-A2-GZ44-10  
June 2004  
1
 
!
!
ATTENTION:  
UN RISQUE MÉCANIQUE EXISTE EN RAISON DE LA ROTATION DES  
PALES DU VENTILATEUR. GARDER LES MAINS ET LES DOIGTS LOIN  
DES PALES DU VENTILATEUR PENDANT LE DEMONTAGE DU CACHE  
DU VENTILATEUR. UTILISER UNIQUEMENT LES ZONES INDIQUÉES DE  
TRACTION POUR DÉMONTER LE CACHE DU VENTILATEUR.  
VORSICHT:  
VERLETZUNGSGEFAHR AUFGRUND ROTIERENDER  
VENTILATORFLÜGEL. BEI ABNAHME DER VENTILATOR-ABDECKUNG  
ODER AUSBAU DES VENTILATORS NICHT IN DEN  
ROTATIONSBEREICH DES VENTILATORS GREIFEN. BEI AUSBAU DES  
VENTILATORS FESTE UND BEWEGLICHE TEILE NUR AN DEN  
GEKENNZEICHNETEN STELLEN BERÜHREN.  
3. Using both hands, place your index fingers in the PULL AREA openings and  
pull forward about an inch to disconnect the fan tray’s connector from the  
backplane. The spinning fan blades will now be visible.  
Ground Wire  
DO NO  
UNDE THE  
C
R
PLUA  
A
USE THE  
T
TIO  
CE FINGERS  
PULL  
AREANS!  
DESIGNA  
L
E
R
L
A
P
A
U
L
E
R
L
A
D
O
U
N
C
N
O
TA  
U
D
S
PU  
LAT  
E
T
E
R
I
T
CO  
H
H
P
E
L
E
F
N
!
E
U
D
F
I
E
L
A
N
S
R
N
A
G
E
R
I
G
T
N
S
E
R
S
Y
A
A
A
T
E
D
00-16794  
4. Wait until the fan blades stop spinning (which should be less than a  
minute). Disconnect the ground wire attached to the fan tray bracket, from the  
quick connect terminal on the chassis.  
5. Remove the fan tray from the chassis.  
8820-A2-GZ44-10  
June 2004  
3
 
Installing a Replacement Fan Tray Assembly  
You will need a Phillips screwdriver to install a replacement fan tray.  
" Procedure  
To install a replacement fan tray:  
1. Hold the replacement fan tray horizontally and guide its tabs into the two card  
guides located inside the right and left side plates.  
PULL  
AREA  
PULL  
AREA  
C
DO NO  
A
U
T
PLA IO  
T
N
UNDER THE  
!
CE FINGERS  
USE THE  
F
AN TRA  
DESIGNA  
PULL AREAS  
Y
TED  
00-16795  
!
WARNING:  
If the chassis is powered on, once the fan tray’s connector is seated in  
the backplane’s connector, the fan blades start spinning. Proper care  
should be taken to prevent contact with the spinning fan blades.  
2. Pressing on the front of the fan tray bracket, push the fan tray half way in and  
attach the ground wire. Then, fully seat the fan tray.  
NOTE:  
When the fan tray is running at full speed the Fan ALARM LED will go  
out, indicating that all fans are operating properly.  
3. Loosen the two screws slightly on each locking bracket and slide the locking  
brackets outward until they engage the slots located on the left and right side  
plates.  
NOTE:  
When properly extended or locked, the brackets should be extended into  
the slots on the side plates and a threaded insert on the locking bracket  
should be aligned with (and visible through) the two outermost holes of  
the fan tray.  
4. Tighten the two screws on each bracket, making sure that the bracket’s  
inserts stay aligned with the holes in the fan tray.  
June 2004  
8820-A2-GZ44-10  
4
 
5. Replace the fan cover plate, aligning the five holes at the bottom with the five  
status LEDs.  
6. Replace and tighten the three screws removed earlier to secure the fan cover  
plate to the chassis.  
Warranty, Sales, Service, and Training Information  
Contact your local sales representative, service representative, or distributor  
directly for any help needed. For additional information concerning warranty,  
sales, service, repair, installation, documentation, training, distributor locations, or  
Paradyne worldwide office locations, use one of the following methods:  
H
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.  
(Be sure to register your warranty at www.paradyne.com/warranty.)  
H
Telephone: Call our automated system to receive current information by fax  
or to speak with a company representative.  
— Within the U.S.A., call 1-800-870-2221  
— Outside the U.S.A., call 1-727-530-2340  
Copyright E 2004 Paradyne Corporation. Printed in U.S.A.  
8820-A2-GZ44-10  
June 2004  
5
 
*8820-A2-GZ44-10*  
*8820–A2–GZ44–10*  
 

Miele Convection Oven h 399 b User Manual
Miele Oven H4880B User Manual
Miller Electric Welder ICE 12C User Manual
Miller Electric Welding System Bobcat 225G User Manual
MTX Audio Speaker 502W User Manual
NEC Car Stereo System CDC TO3 User Manual
NEC Car Video System 2190UXp User Manual
NetComm Network Card NP5420 User Manual
NordicTrack Home Gym NTTL09993 User Manual
Panasonic Microphone 32 1222 User Manual