Panasonic Telephone KXTGA651B User Manual

Installation Manual  
Additional Digital Cordless Handset  
Model No. KX-TGA651  
Thank you for purchasing a Panasonic product.  
This unit is an additional handset compatible with the following  
series of Panasonic Digital Cordless Phone:  
KX-TG4011/KX-TG4021/KX-TG4031/KX-TG4051/  
KX-TG6511/KX-TG6521/KX-TG6531/KX-TG6541/  
KX-TG6581/KX-TG7531  
You must register this handset with your base unit before it can  
be used. This installation manual describes only the steps  
needed to register and begin using the handset. Please read  
the base unit’s operating instructions for further details.  
Charge the batteries for about 7 hours before initial use.  
Please read this installation manual before using the unit and  
save it for future reference.  
For assistance, visit our Web site:  
for customers in the U.S.A. or  
Puerto Rico.  
Printed in Malaysia  
 
PNQX2405ZA DM0410DM0  
Note:  
LUse only the supplied Panasonic AC adaptor PQLV219.  
LThe AC adaptor must remain connected at all times. (It is normal for  
the adaptor to feel warm during use.)  
LMake sure that the wall is strong enough to support the weight of the  
unit.  
Battery installation/Battery charge  
Important:  
LUse the supplied rechargeable batteries. For replacement, we  
recommend using the Panasonic rechargeable batteries noted on  
page 2.  
LWipe the battery ends (S, T) with a dry cloth.  
LAvoid touching the battery ends (S, T) or the unit contacts.  
LConfirm correct polarities (S, T).  
LUSE ONLY Ni-MH batteries AAA (R03) size.  
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.  
Charge for about 7 hours.  
LWhen the batteries are fully charged, the charge indicator goes off and  
Fully chargedis displayed.  
Charge indicator  
Rechargeable  
Ni-MH ONLY  
Confirm  
Charging”  
is displayed.  
Note:  
LIf the batteries are fully charged, but the operating time seems to be  
shorter, clean the battery ends (S, T) and the charge contacts with a  
dry cloth and charge again.  
3
 
Panasonic Ni-MH battery performance (supplied batteries)  
Operation  
Operating time  
In continuous use  
Not in use (standby)  
13 hours max. (If Eco mode is on.)  
11 days max. (If Eco mode is on.)  
Controls  
A Charge indicator  
A
Ringer indicator  
Message indicator  
B Nonslip pad  
H
I
LNonslip pad offers support  
when you cradle the  
handset between your  
shoulder and ear.  
C Speaker  
B C  
J
K
D
E
D {C} (TALK)  
E {s} (SP-PHONE:  
Speakerphone)  
F
G
F Headset jack  
G Dial keypad ({*}: TONE)  
H Receiver  
L
M
I Display  
J {OFF}  
K {FLASH} {CALL WAIT}  
L Microphone  
A
B
M Charge contacts  
NControl type  
A Soft keys  
The handset features 3 soft keys. By pressing a soft key, you can  
select the feature shown directly above it on the display.  
4
 
   
B Navigator key  
{^}, {V}, {<}, or {>}: Scroll through various lists and items.  
? VOL. (Volume: {^} or {V}): Adjust the receiver or speaker  
volume while talking.  
{<} CID (Caller ID): View the caller list.  
{>} REDIAL: View the redial list.  
Note:  
LThe preset melodies used for the ringer tone in this product are used  
with permission of © 2009 Copyrights Vision Inc.  
For KX-TG4011/KX-TG4021 series users  
NUsing the soft keys (operational differences between handsets)  
KX-TGA651 features 3 soft keys, different to your original handset  
which features keys with printed function names.  
Press the soft key corresponding to the desired operation  
(page 4: A).  
Example: When selecting/setting the desired item in programming  
Original handset (printed key name)  
KX-TGA651 soft keys  
{OK}  
{SELECT}{SAVE}  
LSome KX-TGA651 soft key names are different to the button names  
described in your base unit’s operating instructions.  
Registering a handset to a base unit  
1 Base unit:  
NKX-TG4011/KX-TG6511 series  
Press and hold {LOCATOR} for about 5 seconds. (No registration  
tone)  
NKX-TG4021/KX-TG4031/KX-TG4051/KX-TG6521/KX-TG6531/  
KX-TG6541/KX-TG6581/KX-TG7531 series  
Press and hold {LOCATOR} for about 5 seconds until the  
registration tone sounds.  
LIf all registered handsets start ringing, press the same button to  
stop. Then repeat this step.  
5
 
2 Handset:  
Place the handset on the base unit or charger, then wait until a long  
beep sounds and w is displayed.  
Note:  
LIf an error tone sounds, or if _ is displayed, register the handset  
according to the base unit’s operating instructions.  
Display language  
1 {MENU} i {#}{1}{1}{0}  
2 {V}/{^}: Select the desired setting.  
3 {SAVE} i {OFF}  
Date and time  
1 {MENU} i {#}{1}{0}{1} i Enter the current month, date, and  
year by selecting 2 digits for each. i {OK}  
Example: For July 15, 2010, enter {0}{7}{1}{5}{1}{0}.:  
2 Enter the current hour and minute (12-hour clock format) by selecting  
2 digits for each.  
Example: For 9:30, enter {0}{9}{3}{0}.  
3 {AM/PM}: Select AMor PM. i {SAVE} i {OFF}  
Belt clip  
NTo attach  
NTo remove  
6
 
 
series users  
There are some differences in the specification of your original handset  
and the KX-TGA651. The feature differences are described in the chart  
below.  
Main feature differences  
KX-TG4031/  
KX-TG7531  
Feature  
KX-TGA651  
KX-TG4051  
series handset  
series handset  
Display size  
Button size  
1.8 inches  
Large  
1.8 inches  
2.1 inches  
Extra large  
Large  
r
Display mode  
Message list  
r
Operational differences in other features  
NChanging group names in the shared phonebook  
See “Changing group names” (page 9).  
NEditing entries in the shared phonebook  
See “Editing entries” (page 10).  
7
 
For KX-TG4011/KX-TG4021 series users  
There are some differences in the specification of your original handset  
and the KX-TGA651. The feature differences are described in the  
following chart.  
Main feature differences  
KX-TG4011/  
Feature  
KX-TGA651  
1.8 inches  
r
KX-TG4021  
series handset  
Page  
Display size  
1.4 inches  
Phonebook settings  
– Group  
9, 10  
– All erase  
Message alert  
Alarm  
r
r
r
11, 15  
13  
Silent mode  
13  
Voice mail settings  
– Voice mail access no.  
– VM tone detection  
r
r
14  
15  
Time adjustment setting  
Operational differences in other features  
– Date and time (page 6)  
– Chain dial (page 10)  
– Voice guidance language (page 11)  
– Selecting “Greeting only” (page 11)  
– Calling back during playback (Caller ID subscribers only) (page 11)  
8
 
– Caller list operations (Caller ID subscribers only):  
Editing a caller’s phone number before calling back (page 12)  
Erasing all caller information (page 12)  
Storing caller information to the phonebook (page 12)  
– Transferring calls, conference calls (page 12)  
– Deregistering a handset (page 13)  
Differences in the shared phonebook operations  
Adding entries  
When adding an entry to the phonebook, you can assign it to one of 9  
groups.  
1 {C} i {ADD}  
2 Enter the party’s name (16 characters max.). i {OK}  
3 Enter the party’s phone number (24 digits max.). i {OK}  
4 {V}/{^}: Select the desired group. i {SELECT} 2 times  
LTo add other entries, repeat from step 2.  
5 {OFF}  
Changing group names  
The default group name is Group 1to Group 9.  
1 {C} i {MENU} i {V}/{^}: Groupi {SELECT}  
2 {V}/{^}: Select the desired group. i {SELECT}  
3 {V}/{^}: Group namei {SELECT}  
4 Edit the name (10 characters max.). i {SAVE} i {OFF}  
Finding and calling a phonebook entry: Searching by group  
1 {C} i {GROUP}  
2 {V}/{^}: Select the group you want to search. i {SELECT}  
LIf you select All groups, the unit ends the group search.  
3 {V}/{^}: Select the desired entry. i {C}  
9
 
     
Group ringer tone (Caller ID subscribers only)  
You can assign a different ringer tone to the desired group.  
If you select Current ringer(default), the unit uses the same  
ringer tone as for other incoming calls when calls from this group are  
received.  
1 {C} i {MENU} i {V}/{^}: Groupi {SELECT}  
2 {V}/{^}: Select the desired group. i {SELECT}  
3 {V}/{^}: Select the current setting of the group ringer tone. i  
{SELECT}  
4 {V}/{^}: Select the desired ringer tone. i {SAVE} i {OFF}  
Editing entries  
1 {C} i {V}/{^}: Select the desired entry. i {EDIT}  
2 Edit the name if necessary (16 characters max.). i {OK}  
3 Edit the phone number if necessary (24 digits max.). i {OK}  
4 {V}/{^}: Select the desired group. i {SELECT} 2 times i {OFF}  
Erasing all entries  
1 {C} i {MENU} i {V}/{^}: Erase alli {SELECT}  
2 {V}/{^}: Yesi {SELECT}  
3 {V}/{^}: Yesi {SELECT} i {OFF}  
Chain dial  
1 During an outside call, press {MENU}.  
2 {V}/{^}: Phonebooki {SELECT}  
3 {V}/{^}: Select the desired entry. i {CALL}  
 
       
Differences in the answering system operations  
(KX-TG4021 series only)  
Voice guidance language  
1 {MENU} i {#}{1}{1}{2}  
2 {V}/{^}: Select the desired setting. i {SAVE} i {OFF}  
Selecting “Greeting only”  
The unit announces a greeting message to callers but not record  
messages.  
{MENU} i {#}{3}{0}{5} i {V}/{^}: Greeting onlyi  
{SAVE} i {OFF}  
Note:  
LWhen you select Greeting only:  
If you do not record your own message, the unit will play the pre-  
recorded greeting-only message asking callers to call again later.  
Calling back (Caller ID subscribers only)  
While caller information is displayed during playback, press {PAUSE}.  
i {V}/{^}: Call backi {SELECT}  
NEditing the number before calling back  
Press {PAUSE} during playback. i {V}/{^}: Edit & Calli  
{SELECT} i Press {EDIT} repeatedly until the phone number is  
shown in the desired format. i {C}  
Message alert (default: on)  
You can select whether or not the message indicator on the handset  
flashes slowly when new messages are recorded.  
Important:  
LIf you stored the voice mail access number (page 14), the message  
indicator also flashes for newly recorded voice mail messages.  
1 {MENU} i {#}{3}{4}{0}  
2 {V}/{^}: Select the desired setting. i {SAVE} i {OFF}  
 
       
Note:  
LWhile message alert is on, battery operating time is shortened  
(page 4).  
Operational differences in other features  
Caller list operations (Caller ID subscribers only)  
NEditing a caller’s phone number before calling back  
You can edit a phone number in the caller list by removing its area  
code and/or the long distance code “1”.  
1 {<} CID i {V}/{^}: Select the desired entry.  
2 Press {EDIT} repeatedly until the phone number is shown in the  
desired format. i {C}  
NErasing all caller information  
1 {<} CID  
2 {ERASE} i {V}/{^}: Yesi {SELECT} i {OFF}  
NStoring caller information to the phonebook  
1 {<} CID i {V}/{^}: Select the desired entry.  
LTo edit the number, press {EDIT} repeatedly until the phone  
number is shown in the desired format.  
2 {SAVE} i {V}/{^}: Phonebooki {SELECT}  
3 Continue from step 2, “Editing entries”, page 10.  
Transferring calls, conference calls  
1 During an outside call, press {INT} to put the call on hold.  
2 {V}/{^}: Select the desired unit. i {SELECT} i Wait for the  
paged party to answer.  
LIf the paged party does not answer, press {C} to return to the  
outside call.  
3 To complete the transfer: Press {OFF}.  
To establish a conference call: Press {CONF}.  
LTo leave the conference, press {OFF}.  
LTo put the outside call on hold, press {HOLD}. To resume the  
conference, press {CONF}.  
 
       
Deregistering a handset  
1 {MENU} i {#}{1}{3}{1}  
2 {V}/{^}: Select the handset you want to cancel. i {SELECT}  
3 {V}/{^}: Yesi {SELECT} i {OFF}  
Features only available for KX-TGA651  
Alarm  
An alarm sounds at the set time for 3 minutes once or daily.  
Important:  
LSet the date and time beforehand (page 6).  
1 {MENU} i {#}{7}{2}{0}  
2 {V}/{^}: Dailyi {SELECT}  
LWhen you select Once, enter the desired month and date. i  
{OK}  
LWhen you select Off, go to step 5.  
3 Set the desired time. i {AM/PM}: Select AMor PM. i {OK}  
4 {V}/{^}: Select the desired alarm tone. i {SELECT}  
5 {SELECT} i {OFF}  
LWhen the alarm is set, E is displayed.  
Note:  
LTo stop the alarm, press any dial key or place the handset on the base  
unit or charger.  
Silent mode  
Silent mode allows you to select a period of time during which the  
handset will not ring for outside calls.  
Important:  
LSet the date and time beforehand (page 6).  
LWe recommend turning the base unit ringer off in addition to turning  
the silent mode on. (KX-TG4021 series)  
LIf you have set the alarm, the alarm sounds even if the silent mode is  
turned on.  
 
       
1 {MENU} i {#}{2}{3}{8}  
2 {V}/{^}: Select Onor Off. i {SAVE}  
LIf you select Off, press {OFF} to exit.  
3 Enter the desired hour and minute you wish to start this feature.  
4 {AM/PM}: Select AMor PM. i {OK}  
5 Enter the desired hour and minute you wish to end this feature.  
6 {AM/PM}: Select AMor PM. i {SAVE} i {OFF}  
LWhen the silent mode is set, & is displayed.  
NChanging the start and end time  
{MENU} i {#}{2}{3}{7} i Continue from step 3.  
Voice mail service: Storing the voice mail (VM) access number  
Once you have stored your service provider/telephone company’s voice  
mail access number, you can dial it automatically to listen to your voice  
mail messages. You need to store the voice mail access number to  
activate the message alert feature (page 11) for voice mail service.  
1 {MENU} i {#}{3}{3}{1}  
2 Enter your access number (24 digits max.).  
3 {SAVE} i {OFF}  
Note:  
LWhen storing your voice mail access number and your mailbox  
password, press {PAUSE} to add pauses between the access number  
and the password as necessary. Contact your service provider/  
telephone company for the required pause time.  
LTo erase the voice mail access number: Press and hold {CLEAR}  
until all digits are erased in step 2. i {SAVE} i {OFF}  
Voice mail service: Voice mail (VM) tone detection  
Your service provider/telephone company sends special signals  
(sometimes called “voice mail tones” or “stutter tones”) to the unit to let  
you know you have new voice mail messages after you press {C}.  
Soon after you hang up a call or after the phone stops ringing, your unit  
checks the phone line to see if new voice mail messages have been  
recorded. The default setting is On. Turn this feature off when:  
You do not subscribe to voice mail service.  
 
     
Your service provider/telephone company does not send voice mail  
tones.  
Your phone is connected to a PBX.  
If you are not sure which setting is required, contact your service  
provider/telephone company.  
1 {MENU} i {#}{3}{3}{2}  
2 {V}/{^}: Select the desired setting. i {SAVE} i {OFF}  
Voice mail service: Listening to voice mail messages  
The unit lets you know that you have new voice mail messages:  
New Voice Mailis displayed if message indication service is  
available.  
– The message indicator flashes slowly if the message alert feature is  
turned on (page 11).  
1 {VM}  
or  
{MENU} i {#}{3}{3}{0}  
LThe speakerphone turns on.  
LIf there are no new messages in the voice mail, {VM} is not  
displayed.  
2 Follow the pre-recorded instructions. i When finished, press  
{OFF}.  
Note:  
LIf the handset still indicates there are new messages even after you  
have listened to all new messages, turn it off by pressing and holding  
{#} until the handset beeps.  
Turning the time adjustment on/off (Caller ID subscribers only)  
This feature allows the unit to automatically adjust the date and time  
each time caller information including date and time is received. To turn  
this feature on, select Caller ID auto. To turn this feature off,  
select Manual. The default setting is Caller ID auto.  
To use this feature, set the date and time first (page 6).  
1 {MENU} i {#}{2}{2}{6}  
2 {V}/{^}: Select the desired setting. i {SAVE} i {OFF}  
 
   
For your safety  
To prevent severe injury and loss of life/property, read this section carefully before  
using the product to ensure proper and safe operation of your product.  
WARNING  
Power connection  
L Completely insert the AC adaptor/power plug into the power outlet. Failure to do  
so may cause electric shock and/or excessive heat resulting in a fire.  
L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it  
from the power outlet, then wiping with a dry cloth. Accumulated dust may cause  
an insulation defect from moisture, etc. resulting in a fire.  
L Unplug the product from power outlets if it emits smoke, an abnormal smell, or  
makes an unusual noise. These conditions can cause fire or electric shock.  
Confirm that smoke has stopped emitting and contact the Panasonic Call Center  
at 1-800-211- PANA (1-800-211-7262).  
Installation  
L To prevent the risk of fire or electrical shock, do not expose the product to rain or  
any type of moisture.  
L Do not place or use this product near automatically controlled devices such as  
automatic doors and fire alarms. Radio waves emitted from this product may  
cause such devices to malfunction resulting in an accident.  
CAUTION  
Installation and location  
L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet  
is installed near the product and is easily accessible.  
Battery  
L We recommend using the supplied batteries or additional/replacement batteries  
noted on page 2 for replacement battery information. USE ONLY rechargeable  
Ni-MH batteries AAA (R03) size.  
L Do not mix old and new batteries.  
L Do not open or mutilate the batteries. Released electrolyte from the batteries is  
corrosive and may cause burns or injury to the eyes or skin. The electrolyte is  
toxic and may be harmful if swallowed.  
L Exercise care when handling the batteries. Do not allow conductive materials  
such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit  
may cause the batteries and/or the conductive material to overheat and cause  
burns.  
 
L Charge the batteries provided with or identified for use with this product only, in  
accordance with the instructions and limitations specified in this manual.  
L Only use a compatible base unit (or charger) to charge the batteries. Do not  
tamper with the base unit (or charger). Failure to follow these instructions may  
cause the batteries to swell or explode.  
Attention:  
A nickel metal hydride battery that is  
recyclable powers the product you have  
purchased.  
Please call 1-800-8-BATTERY (1-800-822-  
8837) for information on how to recycle this  
battery.  
Other information  
L Operating the product near electrical appliances may cause interference. Move  
away from the electrical appliances.  
L Use only the power cord and batteries indicated in this manual. Do not dispose  
of batteries in a fire. They may explode. Check with local codes for possible  
special disposal instructions.  
Routine care  
L Wipe the outer surface of the product with a soft moist cloth.  
L Do not use benzine, thinner, or any abrasive powder.  
Notice for product disposal, transfer, or return  
L This product can store your private/confidential information. To protect your  
privacy/confidentiality, we recommend that you erase information such as  
phonebook or caller list entries from the memory before you dispose of, transfer,  
or return the product.  
 
FCC and other information  
This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section  
68.316.  
When you hold the phone to your ear, noise might be heard in your Hearing Aid.  
Some Hearing Aids are not adequately shielded from external RF (radio frequency)  
energy. If noise occurs, use an optional headset accessory or the speakerphone  
option (if applicable) when using this phone. Consult with your audiologist or  
Hearing Aid manufacturer about the availability of Hearing Aids which provide  
adequate shielding to RF energy commonly emitted by digital devices.  
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST  
CALLS TO EMERGENCY NUMBERS:  
1) Remain on the line and briefly explain to the dispatcher the reason for the call.  
2) Perform such activities in the off-peak hours, such as early morning or late  
evenings.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired  
operation.  
Privacy of communications may not be ensured when using this phone.  
CAUTION:  
Any changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate this device.  
NOTE:  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
 
FCC RF Exposure Warning:  
L This product complies with FCC radiation exposure limits set forth for an  
uncontrolled environment.  
L This handset may not be collocated or operated in conjunction with any other  
antenna or transmitter.  
L The handset may be carried and operated with only the specific provided belt-  
clip. Other non-tested belt-clips or similar body-worn accessories may not  
comply and must be avoided.  
Notice:  
L FCC ID can be found inside the battery compartment or on the bottom of the unit.  
Compliance with TIA-1083 standard:  
Telephone handsets identified with this logo have reduced  
Compatible with  
noise and interference when used with T-Coil equipped hearing  
aids and cochlear implants.  
Hearing Aid T-Coil  
T
TIA-1083  
Notice  
LThis product is designed for use in the United States of America. Sale or use  
of this product in other countries may violate local laws.  
LCet appareil est conçu pour être utilisé aux États-Unis d’Amérique. La vente  
ou l’emploi de cet appareil dans certains autres pays peut constituer une  
infraction à la législation locale.  
LEste producto está diseñado para usarse en los Estados Unidos de América.  
La venta o el empleo de este producto en ciertos países puede constituir  
violación de la legislación local.  
Lҏ౰ࠢட
छ୽
ٺ
ҢՄ೩Ȅषӵ
ڏ
т୽ড়᎛୵
ٺܖ
ҢȂџ૖ོႂІ࿋Ӵ
ٽݲ
Ȅ  
L
ߩߎ
⵾ຠ
ޔߪ
ᣣᧄ࿖ᄖ
ߩߢ
૶↪
⋡⊛
ߡߒߣ
⸳⸘
ޔࠅ߅ߡࠇߐ
ᣣᧄ࿖ౝ
ߩߢ
 
૶↪
ߪ
ᴺᓞ㆑෻
ࠅߥߣ
߹
ޕߔ
ޔߡߞ
ᒰ␠
ߪߢ
ᣣᧄ࿖ౝ
ߪߡ޿߅ߦ
ේೣ
ߒߣ
 
ߡ
ୃℂ
ࡆ࡯ࠨߩߤߥ
ߪ
ߨ߆ߒ
߹
ޕߔ
 
 
IMPORTANT!  
If your product is not working properly. . .  
1 Reconnect AC adaptor to the base unit.  
2 Check if telephone line cord is connected.  
3 Use rechargeable Ni-MH batteries.  
(Alkaline/Manganese/Ni-Cd batteries CANNOT be used.)  
4 Read troubleshooting page in the base unit’s  
Operating Instructions.  
L
FAQ and troubleshooting hints are available.  
One Panasonic Way, Secaucus, New Jersey 07094  
Copyright:  
This material is copyrighted by Panasonic System Networks Co., Ltd.,  
and may be reproduced for internal use only. All other reproduction, in  
whole or in part, is prohibited without the written consent of Panasonic  
System Networks Co., Ltd.  
© Panasonic System Networks Co., Ltd. 2010  
 

NAD Blu ray Player T587 User Manual
National Instruments Graphics Tablet NI PCI 5114 User Manual
NetComm Network Router N3G002W User Manual
NETGEAR Network Router ac5300 User Manual
Oregon Scientific Thermometer AW129BLRS User Manual
Palm PDAs Smartphones Zodiac User Manual
Panasonic Air Conditioner CS E12GFEW 2 User Manual
Panasonic Blu ray Player DMP BD755 User Manual
Panasonic DVR DMR XW390 User Manual
Patton electronic Network Router 07MOS10xx QS User Manual