SERIES
EX-10
Amplifier Built-in
Ultra-slim Photoelectric Sensor
Amplifier built-in
extraordinarily small
and slim size
UL Recognition
(Excluding 5 m cable length type)
Conforming to EMC Directive
(Excluding EX-15Ⅺ/17Ⅺ)
Smallest body, just 3.5 mm 0.138 in thick
High-speed response time: 0.5 ms
Flexible mounting
It can be mounted in a very small space
as its size is just W10
ן H14.5ן D3.5 mm W0.394
ן H0.571ן D0.138 in (thru- beam, front sensing type).
The sensor is suitable for detecting
small and high-speed traveling objects.
The diffuse reflective type sensor is
front sensing and is so thin that it gives
an impression of being just pasted on
the mounting base. The thru-beam
type is available as front sensing type,
as well as, side sensing type, allowing
flexible mounting.
Diffuse reflective
• Front sensing type
Thru-beam
• Front sensing type
• Side sensing type
Bright 2-color indicator
Waterproof
Operation mode switch
A convenient 2-color indicator has
been incorporated in the miniature
body.
The sensor can be hosed down
because of its IP67 construction and
the non-corrosive stainless steel
mounting bracket.
Note: However, take care that if it is exposed to
water splashes during operation, it may
detect a water drop itself.
Thru-beam type sensor incorporated
with an operation mode switch on the
bifurcation is also available. It helps
you to test the operability before start-
up.
2-color indicator
Red: Operation indicator
Green: Stability indicator
(
)
Operation mode switch
Even for the thru-beam
type sensor, only three
wires have to be con-
nected.
Ten times durable
Red beam makes beam alignment easy
ENS.
Operation indicator
(Orange)
EX
-17
Flexible cable on EX-10-R is 10 times
as durable as conventional model. It is
most suitable for moving parts, such as
robot arm, etc.
The red LED beam projected from the
emitter helps you to align the sensor
heads.
226
08/2005
EX-10
ORDER GUIDE
Type
Appearance
Sensing range
150 mm 5.906 in
Model No.
Output operation
Output
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
EX-11A
EX-11B
EX-13A
EX-13B
EX-19A
EX-19B
500 mm
19.685 in
1 m
3.281 ft
r
F
150 mm 5.906 in
EX-15
EX-17
Switchable
either Light-ON
or Dark-ON
a
500 mm
19.685 in
Light-ON
Dark-ON
Light-ON
Dark-ON
EX-11EA
EX-11EB
EX-13EA
EX-13EB
NPN open-collector transistor
150 mm 5.906 in
500 mm
19.685 in
150 mm 5.906 in
EX-15E
EX-17E
EX-14A
EX-14B
Switchable
either Light-ON
or Dark-ON
500 mm
19.685 in
Light-ON
Dark-ON
2 to 25 mm 0.079 to 0.984 in (Note)
(Convergent point: 10 mm 0.394 in)
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
EX-11A-PN
EX-11B-PN
EX-13A-PN
EX-13B-PN
EX-19A-PN
EX-19B-PN
EX-11EA-PN
EX-11EB-PN
EX-13EA-PN
EX-13EB-PN
150 mm 5.906 in
500 mm
19.685 in
1m
3.281 in
PNP open-collector transistor
150 mm 5.906 in
500 mm
19.685 in
Light-ON
Dark-ON
EX-14A-PN
EX-14B-PN
2 to 25 mm 0.079 to 0.984 in (Note)
(Convergent point: 10 mm 0.394 in)
NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting
brackets (six types).
Note: The sensor does not detect even a specular background if it is separated by 100 mm 3.937 in or more. (However, the background should be
directly opposite.)
228
08/2005
EX-10
ORDER GUIDE
Flexible cable type and 5 m 16.404 ft cable length type
Flexible cable type and 5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) are also available.
• Table of model Nos.
Type
Standard
Flexible cable (2 m 6.562 ft) type 5 m 16.404 ft cable length type
EX-11A
EX-11B
EX-13A
EX-13B
EX-19A
EX-19B
EX-15
EX-11A-R
EX-11B-R
EX-13A-R
EX-13B-R
EX-19A-R
EX-19B-R
EX-11A-C5
EX-11B-C5
EX-13A-C5
EX-13B-C5
EX-19A-C5
EX-19B-C5
EX-15-C5
Front sensing
With operation
mode switch on
the bifurcation
Thru-beam
EX-17
EX-17-C5
EX-11EA
EX-11EB
EX-13EA
EX-13EB
EX-15E
EX-17E
EX-14A
EX-14B
EX-11EA-R
EX-11EB-R
EX-13EA-R
EX-13EB-R
EX-11EA-C5
EX-11EB-C5
EX-13EA-C5
EX-13EB-C5
EX-15E-C5
EX-17E-C5
EX-14A-C5
EX-14B-C5
Side sensing
With operation
mode switch on
the bifurcation
Convergent
reflective
(Diffused beam type)
EX-14A-R
EX-14B-R
Front sensing
229
08/2005
EX-10
OPTIONS
Sensor mounting bracket
Designation
Model No.
Description
• MS-EX10-1
• MS-EX10-11
Mounting bracket for the front sensing type sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-1
MS-EX10-2
MS-EX10-3
MS-EX10-11
MS-EX10-12
MS-EX10-13
Mounting bracket for the side sensing type sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
L-shaped mounting bracket sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
Sensor
mounting
bracket
Material: Cold rolled carbon
Material: Stainless steel (SUS304)
Two M2 (length mm 0.157 in)
pan head screws [stainless steel
(SUS304)] are attached.
steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm 0.157 in)
pan head screws are attached.
4
Mounting bracket for the front sensing type sensor [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
Mounting bracket for the side sensing type sensor [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
• MS-EX10-2
• MS-EX10-12
L-shaped mounting bracket [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
ꢀ
Sensing range: 600 mm 23.622 in [EX-19Ⅺ]
Slit on one side
Slit on both sides
Slit on one side
Slit on both sides
250 mm 9.843 in [EX-13Ⅺ, EX-17]
ꢀ Min. sensing object: 2 mm 0.079 in
"
"
OS-EX10-12
(Slit size 1.2 mm 0.047 in)
"
"
ꢀ
Sensing range: 400 mm 15.748 in [EX-19Ⅺ]
200 mm 7.874 in [EX-13Ⅺ, EX-17]
ꢀ Min. sensing object: 1.2 mm 0.047 in
"
"
Material: Cold rolled carbon
steel (SPCC)
(Uni-chrome plated)
Two M2 (length 8 mm 0.315 in)
pan head screws are attached.
Material: Stainless steel (SUS304)
Two M2 (length mm 0.315 in)
pan head screws [stainless steel
(SUS304)] are attached.
8
ꢀ
Sensing range: 800 mm 31.496 in [EX-19Ⅺ]
350 mm 13.780 in [EX-13Ⅺ]
ꢀ
ꢀ
Min. sensing object: 2 mm 0.079 in
"
"
OS-EX10-15
Slit mask
(Slit size 1.5 mm 0.059 in)
"
"
Sensing range: 500 mm 19.685 in [EX-19Ⅺ]
300 mm 11.811 in [EX-13Ⅺ]
• MS-EX10-3
• MS-EX10-13
ꢀ Min. sensing object: 1.5 mm 0.059 in
"
"
ꢀ
ꢀ
Sensing range: 250 mm 9.843 in [EX-13EⅪ, EX-17E]
Min. sensing object: 2 mm 0.079 in
Slit on one side
Slit on both sides
"
"
OS-EX10E-12
(Slit size 1.2 mm 0.047 in)
"
"
ꢀ
ꢀ
Sensing range: 200 mm 7.874 in [EX-13EⅪ, EX-17E]
Min. sensing object: 1.2 mm 0.047 in
"
"
It is useful for beam alignment of thru-beam type sensors.
The optimum receiver position is given by indicators, as
well as an audio signal.
Sensor checker
(Note)
CHX-SC2
MS-M2
Material: Cold rolled carbon
steel (SPCC)
Material: Stainless steel (SUS304)
Two M2 (length mm 0.157 in)
pan head screws [stainless steel
(SUS304)] and two M2 (length
4
(Uni-chrome plated)
Mounting screws with washers (50 pcs. lot). It can mount
securely as it is spring washer attached.
Two M2 (length 4 mm 0.157 in)
pan head screws, and two
M2 (length 8 mm 0.315 in)
pan head screws are attached.
Mounting screw
8
mm 0.315 in) pan head screws
[stainless steel (SUS304)] are
attached.
Slit mask
• OS-EX10-12
• OS-EX10-15
• OS-EX10E-12
Example of mounting
(OS-EX10E-12)
Tighten along with the sensor
mounting bracket.
Sensor checker
• CHX-SC2
POWER
CHX-SC2
LEVEL
Sensor checker
230
08/2005
EX-10
SPECIFICATIONS
Convergent reflective
(Diffused beam type)
Thru-beam
Thru-beam • with operation mode switch on bifurcation
Type
Front sensing Side sensing Front sensing Side sensing Front sensing Front sensing Front sensing Side sensing Front sensing Side sensing
Model
No.
(Note 1)
EX-11A(-PN) EX-11EA(-PN) EX-13A(-PN) EX-13EA(-PN) EX-19A(-PN) EX-14A(-PN)
Light-ON
Dark-ON
EX-15
EX-15E
EX-17
EX-17E
(Note 2) (Note 2) (Note 2) (Note 2)
EX-11B(-PN) EX-11EB(-PN) EX-13B(-PN) EX-13EB(-PN) EX-19B(-PN) EX-14B(-PN)
Item
2 to 25 mm 0.079 to
0.984 in (Note 3)
(Conv. point: 10 mm 0.394 in)
Sensing range
150 mm 5.906 in
500 mm 19.685 in
1 m 3.281 ft
150 mm 5.906 in
500 mm 19.685 in
"2 mm "0.079 in
opaque object
Setting distance between
emitter and receiver:
"1 mm "0.039 in opaque object "2 mm "0.079 in opaque object
"0.1 mm "0.004 in "1 mm "0.039 in opaque object "2 mm "0.079 in opaque object
Setting distance between
emitter and receiver:
150 mm 5.906 in
Setting distance between
emitter and receiver:
500 mm 19.685 in
copper wire
Setting distance between
emitter and receiver:
150 mm 5.906 in
Setting distance between
emitter and receiver:
500 mm 19.685 in
Min. sensing object
Setting distance:
10 mm 0.394 in
(
) (
)
(
) (
)
(
)
(
)
1 m 3.281 ft
15 % or less of
Hysteresis
operation distance
0.1 mm 0.004 in
or less
Repeatability
(perpendicular to sensing axis)
0.05 mm 0.002 in or less
0.05 mm 0.002 in or less
30 mA or less
Supply voltage
12 to 24 V DC
ע 10 % Ripple P-P 10 % or less Emitter: 10 mA or less, Receiver: 15 mA or less 20 mA or less
Current consumption
<NPN output type>
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1 V or less (at 50 mA sink current)
0.4 V or less (at 16 mA sink current)
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less
(between output and 0 V)
• Residual voltage: 1.5 V or less
(at 100 mA sink current)
• Residual voltage: 0.4 V or less
(at 16 mA sink current)
Output
<PNP output type>
PNP open-collector transistor
• Maximum source current: 50 mA
• Applied voltage: 30 V DC or less (between output and
ם V) • Residual voltage: 1 V or less (at 50 mA source current)
0.4 V or less (at 16 mA source current)
Utilization category
Short-circuit protection
Response time
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON),
located on the bifurcation
Operation indicator
Incident beam indicator
Stability indicator
Red LED (lights up when the output is ON)
Red LED (lights up under light received condition),
located on the receiver
Green LED (lights up under stable light received condition
or stable dark condition), located on the receiver
Green LED (lights up under stable light received condition or
stable dark condition)
Pollution degree
Protection
3 (Industrial environment)
IP67 (IEC)
Ambient temperature
Ambient humidity
Ambient illuminance
EMC
מ 25 toם 55 ЊC מ 13 toם 131 ЊF (No dew condensation or icing allowed), Storage:מ 30 toם 70 ЊC מ 22 toם 158 ЊF 35 to 85 % RH, Storage: 35 to 85 % RH
Sunlight: 10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving face
EN 50081-2, EN 50082-2, EN 60947-5-2
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (modulated)
Enclosure: Polyethylene terephthalate
Lens: Polyalylate
Enclosure: Polyethylene terephthalate
Lens: Polyalylate, Bifurcation: Polyalylate
Material
0.2 mm2 3-core cabtyre cable, 2 m 6.562 ft long (beyond bifur-
cation; from emitter / receiver to bifurcation: 0.5 m 1.640 ft long)
0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Cable (Note 4)
Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable
(thru-beam type: emitter and receiver).
Extension up to total 100 m 328.084 ft is
possible with 0.3 mm2, or more, cable.
Cable extension
Weight
Emitter: 20 g approx., Receiver: 20 g approx.
Mounting screws: 1 set
20 g approx.
55 g approx.
Mounting screws:
1 set
Accessories
Mounting screws: 1 set, Adjusting screwdriver: 1 pc.
Notes: 1) Model Nos. having the suffix ‘-PN’ are PNP output type.
Notes: 2) Either Light-ON or Dark-ON can be selected by the operation mode switch (located on the bifurcation).
Notes: 3) The sensing range of convergent reflective type sensor is specified for white non-glossy paper (50
ן 50 mm 1.969ן 1.969 in) as the object. Notes: 4) The flexible cable type (model Nos. having suffix -R
) has a 0.1 mm2 3-core (thru-beam type emitter : 2-core) flexible cabtyre cable, 2 m 6.562 ft long.
‘
’
231
08/2005
EX-10
I/O CIRCUIT AND WIRING DIAGRAMS
EX-11Ⅺ EX-13Ⅺ
NPN output type
EX-19Ⅺ EX-14Ⅺ
I/O circuit diagram
Wiring diagram
Color code
D
(Brown)
ם V Load
(Black)
Output (Note)
ם מ 12 to 24 V DC
ע 10 % Brown
Tr
50 mA max.
(Blue) 0 V
Load
ZD
S
ם מ Black (Note)
Blue
12 to 24 V DC
ע 10 % Internal circuit
Users’ circuit
Note: The emitter of the thru-beam type sensor does not
incorporate the output.
Note: The emitter of the thru-beam type sensor does not
incorporate the black wire.
Symbols … D : Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr : NPN output transistor
EX-11Ⅺ-PN EX-13Ⅺ-PN
PNP output type
EX-19Ⅺ-PN EX-14Ⅺ-PN
I/O circuit diagram
Wiring diagram
Color code
(Brown)
ם V ZD
50 mA max.
ם מ 12 to 24 V DC
ע 10 % Brown
Tr
(Black) Output (Note)
Load
ם מ Black (Note)
Load
12 to 24 V DC
ע 10 % D
(Blue) 0 V
Blue
Internal circuit
Users’ circuit
Note: The emitter of the thru-beam type sensor does not
incorporate the output.
Note: The emitter of the thru-beam type sensor does not
incorporate the black wire.
Symbols … D : Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr : PNP output transistor
EX-15 EX-15E
NPN output type
EX-17 EX-17E
I/O circuit diagram
Wiring diagram
Color code
D
(Brown)
ם V Load
ם מ (Black) Output
12 to 24 V DC
ע 10 % Tr
100 mA max.
(Blue) 0 V
ZD
Internal circuit
Users’ circuit
Symbols … D : Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr : NPN output transistor
Brown
Load
ם מ Black
12 to 24 V DC
ע 10 % Blue
232
08/2005
EX-10
SENSING CHARACTERISTICS (TYPICAL)
All models
Thru-beam type
Correlation between setting distance and excess gain
100
100
50
50
EX-13Ⅺ
EX-17Ⅺ
EX-19Ⅺ
10
5
10
5
E
E
EX-11Ⅺ
EX-15Ⅺ
1
1
0
200
400 600
7.874 15.748 23.622 31.496 39.370
Setting distance L (mm in)
800 1,000
0
1
2
3
4
5
3.281 6.562 9.843 13.123 16.404
Setting distance L (m ft)
EX-11Ⅺ EX-11EⅪ
Thru-beam type
EX-15Ⅺ EX-15EⅪ
Parallel deviation
Angular deviation
200
200
7.874
7.874
EX-11Ⅺ
EX-15Ⅺ
150
5.906
150
5.906
EX-11Ⅺ
EX-11EⅪ
EX-15Ⅺ
EX-15EⅪ
EX-11EⅪ
EX-15EⅪ
EX-11Ⅺ
EX-15Ⅺ
EX-11EⅪ
EX-15EⅪ
100
100
3.937
3.937
Emitter
Emitter
Emitter
Emitter
50
1.969
50
1.969
#
#
$
$
L
L
L
L
EX-11Ⅺ
EX-15Ⅺ
EX-11EⅪ
EX-15EⅪ
Receiver
Receiver
0
Receiver
Receiver
0
100
3.937
50
1.969
Left
0
50
1.969
Right
100
3.937
20
10
Left
0
10
Right
20
Center
Operating angle ( ° )
Center
$
Operating point ?(mm in)
EX-13Ⅺ EX-13EⅪ
Thru-beam type
EX-17Ⅺ EX-17EⅪ
Parallel deviation
Angular deviation
Parallel deviation with slit masks ("1.2 mm "0.047 in) Parallel deviation with slit masks ("1.5 mm "0.059 in)
800
800
400
400
EX-13Ⅺ/17Ⅺ
31.496
Slit on one side
or both sides
31.496
15.748
15.748
Slit on one side
EX-13Ⅺ/17Ⅺ
600
600
EX-13Ⅺ
EX-17Ⅺ
300
300
Slit on both sides
23.622
23.622
11.811
11.811
EX-13EⅪ/17EⅪ
Slit on one side
EX-13Ⅺ
EX-17Ⅺ
EX-13EⅪ
EX-17EⅪ
EX-13EⅪ
EX-17EⅪ
EX-13EⅪ/17EⅪ
Slit on
both sides
400
15.748
400
15.748
200
7.874
200
7.874
Emitter
Slit on one side,
Emitter
Emitter
Emitter
sensing range: 350 mm 13.78 in
Slit on both sides,
Emitter
Emitter
#
200
7.874
200
7.874
L
100
3.937
100
3.937
sensing range: 300 mm 11.81 in
$
$
#
#
#
L
L
L
L
L
EX-13Ⅺ
EX-17Ⅺ
EX-13EⅪ
EX-17EⅪ
EX-13Ⅺ
EX-13EⅪ
Receiver
20
Receiver
Receiver
Receiver
Receiver
Receiver
EX-17Ⅺ
EX-17EⅪ
0
0
0
0
100
3.937
50
1.969
Left
0
50
1.969
Right
100
3.937
20
10
Left
0
10
Right
20
40
20
0
40
1.575
100
50
0
50
1.969
Right
100
3.937
1.575
0.787
0.787
Right
3.937
1.969
Center
Left
Center
Center
$
Left
Center
Operating angle ( ° )
Operating point ?(mm in)
Operating point ?(mm in)
Operating point ?(mm in)
EX-19Ⅺ
Thru-beam type
Parallel deviation
Angular deviation
Parallel deviation with slit masks ("1.2 mm "0.047 in) Parallel deviation with slit masks ("1.5 mm "0.059 in)
800
31.496
Slit on one side
Slit on one side
1,000
39.370
1,000
39.370
1,000
39.370
600
23.622
Slit on both sides
400
15.748
Emitter
Emitter
500
500
500
Emitter
Emitter
19.685
19.685
19.685
$
L
#
L
200
#
L
#
L
7.874
Slit on both sides
Receiver
Receiver
100 200
Receiver
100
3.937
Right
Receiver
0
0
0
0
200
100
0
200
7.874
40
20
Left
0
20
Right
40
200
100
0
100
200
7.874
200
100
0
7.874
3.937
7.874
3.937
3.937
Right
Operating point ?(mm in)
7.874
3.937
3.937
Right
7.874
Center
Operating angle ( Њ )
Left
Center
Left
Center
Left
Center
$
Operating point ?(mm in)
Operating point ?(mm in)
233
08/2005
EX-10
SENSING CHARACTERISTICS (TYPICAL)
EX-14Ⅺ
Convergent reflective type
Sensing fields
•
Horizontal (left and right) direction • Vertical (up and down) direction
40
40
50
ן 50 mm 1.969ן 1.969 in 1.575
1.575
Non-glossy paper
)
)
i
in
30
1.181
30
1.181
#
7 mm
0.276 in
50
ן 50 mm
1.969
ן 1.969 in
L
White
Non-glossy paper
20
0.787
20
0.787
White
10
10
#
0.394
0.394
7.75
S
N4
S
N4
5
0.197
Down
L
mm
0.305 in
0
0
10
5
0
5
10
0.394
10
0
5
10
0.394
0.394
0.197
0.197
0.394
0.197
Up
Center
Left
Center
Right
Operating point ?(mm in)
Operating point ?(mm in)
Correlation between lightness and sensing range
Correlation between material (50
ן 50 mm 1.969ן 1.969 in) and sensing range 40
80
The sensing region is represent-
ed by oblique lines in the left
figure. However, the sensitivity
should be set with enough mar-
gin because of slight variation in
products.
The bars in the graph indicate the
sensing range for the respective
material. However, there is a
slight variation in the sensing
range depending on the product.
Further, if there is a reflective
object (conveyor, etc.) in the
background of the sensing object,
since it affects the sensing,
separate it by more than twice the
sensing range shown in the left
graph.
1.575
3.150
30
1.181
60
2.362
20
0.787
40
1.575
Sensing region
10
0.394
20
0.787
10
0.394
0
0
N2
Dark
N4
N6
N8
Light
Lightness shown on the left
may differ slightly from the
actual object condition.
Lightness
(
)
N1 N2 N3 N4 N5 N6 N7 N8 N9
PRECAUTIONS FOR PROPER USE
Operation mode switch (EX-15Ⅺ, EX-15EⅪ, EX-17Ⅺ and EX-17EⅪ only)
This product is not a safety sensor. Its use is not
intended or designed to protect life and prevent body
injury or property damage from dangerous parts of
machinery. It is a normal object detection sensor.
Operation mode switch
L: Light-ON
D: Dark-ON
Mounting
Operation indicator (Orange)
Lights up when the output is
ON.
• In case of mounting on tapped holes (Unit: mm in)
Side sensing
Front sensing
Switch
Sensing
direction
Sensing
direction
11
0.433
Description
position
Attached
screw
[M2 (length 8 0.315)]
11
0.433
Attached
screw
[M2 (length 10 0.394)]
Light-ON mode is set when the switch is turned fully
clockwise (L side).
M2
ן 0.4 0.016 hole M2
ן 0.4 0.016 hole tapped, 6 0.157 deep
tapped, 7 0.276 deep
The tightening torque should be 0.2 Nꢀm or less.
In case of using attached screws and nuts (Unit: mm in)
Dark-ON mode is set when the switch is turned fully
counterclockwise (D side).
•
Side sensing
Front sensing
Flat washers
Nuts
Others
Sensing
direction
Sensing
11
0.433
• Do not use during the initial transient time (50ms)
(EX-15Ⅺ, EX-15EⅪ, EX-17Ⅺ, EX-17EⅪ: 100 ms) after
the power supply is switched on.
direction
Attached
Spring
11
0.433
Attached
screw
[M2 (length 8 0.315)]
screw
washers
[M2 (length 10 0.394)]
Thickness of
Thickness of
mounting plate: 2 0.079 or less
mounting plate: 2.5 0.098 or less
The tightening torque should be 0.2 Nꢀm or less.
234
08/2005
EX-10
DIMENSIONS (Unit: mm in)
EX-11AⅪ EX-11BⅪ EX-13AⅪ
Sensor
EX-13BⅪ EX-19AⅪ EX-19BⅪ
Stability
indicator
(Green)
Operation
indicator
(Red)
10
3.5
0.394
3.5
0.138
0.138
2.1
6.45
0.254
10
0.394
5.5
5.5
0.217
2.1
0.083
0.083
1.75
0.069
0.217
1.75 0.069
1.75 0.069
1.75 1.5
0.069 0.059
4
4
Beam-
receiving
part
0.157
0.157
11
0.433
11
0.433
14.5
0.571
14.5
0.571
Beam-
emitting
part
4.5
4.5
0.177
0.177
6.5
0.256
2-"2.2 "0.087
mounting holes
6.5
0.256
2-"2.2 "0.087
mounting holes
"2.5 "0.098 cable, 2 m 6.562 ft long
"2.5 "0.098 cable, 2 m 6.562 ft long
Emitter
Receiver
EX-11EAⅪ EX-11EBⅪ
Sensor
EX-13EAⅪ EX-13EBⅪ
Stability
indicator (Green)
10
Operation
indicator (Red)
0.394
6.45
0.254
1.75
0.069
10
0.394
4.5
4.5
0.177
0.177
2.25
0.089
1.75 0.069
1.75 0.069
1.75 1.5
0.069 0.059
2.25
0.089
4
Beam-
receiving
part
4
Beam-
emitting
part
0.157
0.157
14.5
11
14.5
0.571
11
0.433
0.571
0.433
4.5
0.177
4.5
0.177
6.5
0.256
6.5
2-"2.2 "0.087
mounting holes
2-"2.2 "0.087
mounting holes
0.256
4.2
0.165
4.2
0.165
"2.5 "0.098 cable, 2 m 6.562 ft long
"2.5 "0.098 cable, 2 m 6.562 ft long
Emitter
Receiver
EX-15
EX-15E
EX-17E
Sensor
Sensor
EX-17
Emitter
Receiver
Emitter
Receiver
Stability indicator (Green)
10
10
0.394
Stability indicator (Green)
Incident beam indicator (Red)
10
0.394
1.75
0.069
Incident beam indicator (Red)
0.394
6.45 0.254
5.5
0.217
4.5
4.5
1.75 0.069
1.75
0.069
10 0.394
1.75
0.069
3.5
0.138
1.5
3.5
0.177
2.25
0.089
0.177
2.25
0.089
1.75
4
6.45 0.254
4
0.059
0.138
0.069
1.5
0.059
0.157
1.75
1.75
0.069
5.5
0.157
4
1.75
0.069
2.1
0.083
0.069
0.217
2.1
0.083
0.157
Beam-
emitting
part
Beam-
receiving
part
14.5
11
0.433
11
0.433
14.5
0.571
0.571
4
0.157
11
Beam-
receiving
part
Beam-
emitting
part
14.5 11
0.571 0.433
14.5
0.571
0.433
4.5 0.177
4.5 0.177
4.5
0.177
4.5
4.2
0.165
4.2
0.165
2-"2.2 "0.087
mounting holes
2-"2.2 "0.087
mounting holes
0.177
2-"2.2 "0.087
mounting holes
500
19.685
2-"2.2 "0.087
mounting holes
500
19.685
"2.5 "0.098 cables
"2.5 "0.098 cables
15.2 0.598
15.2 0.598
Operation indicator
(Orange)
19.2
19.2
Operation indicator
(Orange)
0.756
0.756
38
1.496
38
1.496
Operation mode switch
Operation mode switch
"3.8 "0.150 cable,
2 m 6.562 ft long
"3.8 "0.150 cable,
2 m 6.562 ft long
8
1 0.039
8
1 0.039
0.315
7
7
0.315
0.276
0.276
235
08/2005
EX-10
DIMENSIONS (Unit: mm in)
EX-14AⅪ
Sensor
EX-14BⅪ
13
0.512
6.45
Stability indicator
(Green)
0.254
2.75
3.5
5
0.108
1.75
0.138
Operation
indicator (Red)
0.197
2.1
0.083
0.069
1.75 1.5
0.069 0.059
4.5
0.177
Beam-
receiving
part
11 14.5
0.433 0.571
Beam-emitting part
4.5
0.177
8
0.315
2-"2.2 "0.087 mounting holes
"2.5 "0.098 cable,
2 m 6.562 ft long
MS-EX10-1
Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14Ⅺ
t 1.2
t 0.047
7.6
0.299
20 0.787
7.6
0.299
(0.7)
t 1.2
t 0.047
(0.028)
3.7
0.146
(4.9)
(0.193)
3.7 3.5
0.146 0.138
22.75 0.896
13
20
0.512
0.787
10.75
0.423
8
3.5
5
0.197
6.5
8
3.5
0.138
4-M2
ן 0.4 0.016 thru-hole threads
0.138
0.256 0.315
1.25
0.049
Beam-
emitting
part
2-"3.4 "0.134 mounting holes
0.315
(8.8)
(0.346)
15
0.591
8
3
0.118
11
0.433
15
0.591
11
0.433
Beam-
receiving
part
8
0.315
0.315
4.25 0.167
2-"3.4 "0.134 mounting holes
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm 0.157 in) pan head screws are attached.
MS-EX10-2
Sensor mounting bracket (Optional)
Assembly dimensions
t 1.2
t 0.047
Mounting drawing with EX-11EⅪ and EX-13EⅪ
7.6
0.299
(2.3)
(0.091)
7.6
t 1.2
0.299
t 0.047
6.25
0.246
4.5
6.25
(7.45)
(0.293)
0.177
0.246
20
0.787
3.2
0.126
(1.3)
1.4
0.055
3.2
(0.051)
0.126
4
0.157
10
0.394
0.25
0.010
1.25
0.049
1.4
0.055
11
0.433
8
15
Beam-
receiving
part
2.5 0.098
0.315 0.591
15
0.591
11
0.433
8
0.315
2-M2
ן 0.4 0.016 thru-hole threads
4.25
8
3.5
0.138
0.167
0.315
3.5
0.138
8
0.315
20
0.787
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 8 mm 0.315 in) pan head
screws are attached.
236
08/2005
EX-10
DIMENSIONS (Unit: mm in)
MS-EX10-3
Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14Ⅺ
15
0.591
10.8
0.425
t 1.2
t 0.047
(2.75)
(0.108)
7 0.276
10.5
0.413
(0.7)
(0.028)
3.2
1.4
0.126
0.055
3.5
10.5
8
0.138
0.413
4-M2
ן 0.4 0.016 thru-hole threads
3.2
t 1.2
t 0.047
0.315
Beam-
1.75 0.069
Beam-
receiving part
0.126
7
0.276
13
emitting part
0.512
1.25
0.049
5
6.25
0.197 0.246
1.4
0.055
10.8
0.425
6.5
0.256
3
0.118
8
11
15
0.591
0.315
0.438
11
0.433
2
0.079
4.25
0.167
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm 0.157 in) pan head screws, and two M2
(length 8 mm 0.315 in) pan head screws are attached.
MS-EX10-11
Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14Ⅺ
t 1.2
t 0.047
8.1
0.319
20
0.787
(0.7)
(0.028)
t 1.2
8.1
0.319
t 0.047
(4.9)
(0.193)
3.7
20
0.146
22.75
0.896
3.5
0.138
0.787
3.7
0.146
4-M2
ן 0.4 0.016 thru-hole threads
6.5
8
3.5
13
3.2
0.126
0.256 0.315 0.138
1.4
0.055
0.512
5
3.5
0.138
10.75 0.423
0.197
8 0.315
(9.3)
(0.366)
3.2
11
0.433
8
15
1.25
0.049
0.126
0.315 0.591
1.4
0.055
Beam-emitting part
Beam-receiving part
3.2
0.126
1.4
0.055
3
0.118
8
11 15
0.433 0.591
0.315
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] are
attached.
4.25
0.167
1.4
0.055
3.2
0.126
MS-EX10-12
Sensor mounting bracket (Optional)
8.1
0.319
t 1.2
t 0.047
Assembly dimensions
Mounting drawing with EX-11EⅪ and EX-13EⅪ
(2.3)
(0.091)
8.1
t 1.2
6.25
0.246
0.319
t 0.047
4.5
6.25
(7.45)
(0.293)
20
0.787
0.177
0.246
1.4
3.2
0.055
0.126
(1.3)
(0.051)
4
0.157
0.25
0.010
10
0.394
1.4
0.055
1.25
0.049
8
0.315
15
0.591
11
0.433
3.2
0.126
2-M2
ן 0.4 0.016 2.5 0.098
1.4
0.055
Beam-
receiving
part
thru-hole threads
8
15 11
0.591 0.433
0.315
3.2
0.126
3.5
0.138
8
0.315
1.4
4.25
0.167
0.055
Material: Stainless steel (SUS304)
3.2
Two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are
attached.
0.126
3.5
0.138
8
0.315
20
0.787
237
08/2005
EX-10
DIMENSIONS (Unit: mm in)
MS-EX10-13
Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14Ⅺ
7
10.5
0.413
0.276
(2.75)
(0.108)
t 1.2
t 0.047
10.8
0.425
3.2 0.126
1.4 0.055
3.2 0.126
1.4
0.055
(0.7)
(0.028)
8
0.315
15
0.591
4-M2
ן 0.4 0.016 thru-hole threads
t 1.2
t 0.047
1.75
0.069
13
3.5
0.138
0.512
10.8
0.425
10.5
0.413
7
6.5 0.256
5
6.25
0.197 0.246
1.25
0.049
0.276
1.4
0.055
3.2
0.126
2
11
0.433
Beam-emitting
part
0.079
3
0.118
11
0.433
15
0.591
8
Beam-receiving
part
0.315
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan
head screws [stainless steel (SUS304)]
and two M2 (length 8 mm 0.315 in) pan
head screws [stainless steel (SUS304)]
are attached.
1.4
4.25
0.167
0.055
3.2
0.126
238
08/2005
|