Panasonic Security Camera AK HRP900P User Manual

Camera Controller  
Model  
AK-HRP900P  
Before attempting to connect, operate or adjust this product,  
please read these instructions completely and save this manual for future use.  
 
Contents  
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Check the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Controls and their Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
_ Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
_ Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
_ Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
How To Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12  
_ Lens connection in the case of no swivel stand . . . . . . . . . . . . . . . . . . . . . . .13  
Multi-purpose digital camera control system configuration 1 . . . . . . . . . . . . . . .14  
Multi-purpose digital camera control system configuration 2 . . . . . . . . . . . . . . .15  
Multi-purpose digital camera control system configuration 3 . . . . . . . . . . . . . . .16  
Communication speed setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
Example of Rack Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
_ How to rack-mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
_ How to change the rear panel position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Appearance and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
3
 
Outline  
This unit is a camera controller for multi-purpose camera (AK-HC900P). This  
unit is connected to a multi-purpose camera with one multi-cable, and capable  
of transmitting and receiving various camera and lens control signals, analog  
picture signals of cameras, and generator lock signals (3-value SYNC).  
The extension distance between this unit and the camera is 33 ft (10m) max.  
It is possible to control the swivel stand from the pan-tilt control panel AW-  
RP301 by using the swivel stand control input connector.  
Check the Accessories  
Coupling . . . . . . . . . . . . . . . . . . . . . . .1 pc  
Multi-cable . . . . . . . . . . . . . . . . . . . . . .1 pc  
Seal . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc  
Setscrews . . . . . . . . . . . . . . . . . . . . .8 pcs  
M4 x 8 mm . . . . . . . .4 pcs  
M5 x 8 mm . . . . . . . .4 pcs  
Precautions for Use  
We recommend that the AC adapter AW-PS505P is used for power supply.  
Handle the unit with care.  
If dropped or given a strong shock, it may cause a trouble or accident.  
Use the unit in a temperature range of 32oF to 104oF (0oC to + 40oC).  
If used at a temperature below 32oF or higher than 104oF, it may cause bad influences to  
the component parts.  
Turn off the power before connecting or disconnecting the cable.  
When connecting or disconnecting the cable, be sure to turn off the power switch of the  
unit beforehand.  
Avoid using the unit outdoors.  
Install the unit 3.3 ft (1 m) away from the monitor.  
Maintenance  
Pull out the power cord plug and clean the unit with dry cloth. If it is hard to clean,  
moisten the cloth with a diluted neutral detergent solution and squeeze it well and lightly  
wipe the unit.  
Precautions  
Do not use volatile solvents such as benzene or thinner.  
When using a chemical mop, carefully read the instructions.  
4
 
Controls and their Functions  
_Operation panel  
1
2
3
<
=
>
Camera Controller  
SCENE  
ON  
OFF  
OPERATE  
CAM  
POWER  
ALARM  
TEST  
PRE  
USER1  
USER2  
?
@
A
SD CARD  
MODE  
BAR  
AUTO  
WHITE  
BLACK  
TALLY  
4
5
6
GAIN  
BLACK  
B
C
D
E
MENU  
ON  
MENU  
4
7
ND FLTER  
CLEAR 1/4 1/16 1/32  
CC FLTER  
3200 4300 6300 CROSS  
PRESET  
3
1
2
5
F
G
8
9
GAIN  
9dB  
SHUTTER  
OFF STEP SYNCRO  
0
18dB  
S1  
S2  
SPEED  
TELE  
ZOOM  
FOCUS  
S3  
FAR  
CHECK  
IRIS  
M-PED  
AUTO  
WIDE  
NEAR  
:
; HIJ  
K
L
1 Power indication LED [POWER]  
It is lighted green when the power control switch 2 is ON. It goes out when the power  
control switch 2 is OFF.  
2 Power control switch [POWER ON/OFF]  
With this switch turned ON, the unit and the camera connected are simultaneously  
turned on. With it turned OFF, both of the unit and the camera are turned off.  
3 SD card slot [SD CARD]  
With an SD card inserted, the camera setting data can be recorded on the SD card.  
4 Tally LED [TALLY]  
It is lighted red when tally signal is input to the tally signal input terminal Q.  
5
 
Controls and their Functions  
5 Menu operation switch [MENU]  
Operation switch for camera menu.  
Item selection or data change can be done by turning this switch. When this switch  
pushed, the item and data are settled.  
6 Menu ON switch [MENU ON]  
Used to turn the camera menu ON/OFF.  
7 Preset memory switch [MEMO]  
Preset memory can be done up to 5 points with respect to lens zoom, focus, and iris  
position (when iris select switch K is at [MANU]). When using the preset memory, first  
set the lens focus, zoom, and iris. Next, push this switch, then the switch is lighted.  
Subsequently, push the desired preset position select switch 8. With the data stored in  
the memory, the switch is lighted.  
8 Preset position select switch [PRESET]  
It calls the lens zoom, focus and iris settings previously stored in the memory, and  
brings the lens into preset operation.  
9 Speed change switch [SPEED]  
High speed operation is obtained when the zoom operation lever : and the focus  
adjust lever ; are operated while pressing this switch. The switch is lighted while being  
pressed.  
: Zoom operation lever [ZOOM TELE/WIDE]  
Used for zoom operation of the lens. The zoom speed changes with the shifting angles  
of the lever. With the zoom operation lever direction change switch T set at [NOR],  
when the lever is shifted to [TELE], the zoom operates in a telescopic mode, and when  
shifted to [WIDE], it operates in a wide angle mode. With the zoom operation lever  
direction change switch T set to [REV], the zoom can be operated in the opposite  
direction.  
; Focus adjust lever [FOCUS FAR/NEAR]  
Used to adjust the lens focus. The focus can be controlled in speed variable fashion by  
regulating the shifting angle of this lever.  
With the focus adjust direction change switch U set at [NOR], when this lever is shifted  
to [FAR], the focus is adjusted to a far distance, and when shifted to [NEAR], the focus  
is adjusted to a near distance. With the focus adjust direction change switch U set to  
[REV], the focus can be adjusted in the opposite direction.  
< Operation panel active switch [OPERATE]  
This is an active switch for panel function. It can be operated when the switch is lighted.  
It does not work when the switch is not lighted.  
6
 
Controls and their Functions  
= Alarm indication LED [ALARM]  
It lights up when an alarm is generated (in case of fan stop, wrong communication  
speed, etc.).  
Note:  
In case of wrong communication speed, change the DIP SW position in the unit to  
match the camera and communication speed so that the alarm goes out.  
> Scene file select switch [SCENE]  
Used to select the scene file previously set on the camera.  
Note:  
With [PRESET] selected, it results in the factory-adjusted setting.  
? Mode select switch [MODE]  
Used to select the camera color bar signal, test signal and camera picture signal. With  
the switch set to [BAR], [TEST], the color bar signal and the test signal are output from  
the monitor signal output terminal of this unit. With it set to [CAM], the picture taken by  
the camera is output.  
@ Auto white start switch [AUTO WHITE]  
With this switch pressed, the white balance is automatically adjusted. During the  
operation, WHTE LED blinks, and it goes out when the adjustment is normally finished.  
In case of NG, it lights up for a while and then goes out.  
Note:  
It does not operate when the mode is [BAR].  
A Auto black start switch [AUTO BLACK]  
With this switch pressed, the lens is automatically closed, and the black balance is  
adjusted. During the operation, BLACK LED blinks, and it goes out when the  
adjustment is normally finished. In case of NG, it lights up for a while and then goes  
out.  
B R/B gain adjust volume [GAIN]  
Used to adjust the R/B signal gain of the camera.  
C R/B pedestal adjust volume [BLACK]  
Used to adjust the R/B signal pedestal level of the camera.  
D ND filter select switch [ND FILTER]  
Used to select the optical filter (ND) of the camera.  
E CC filter select switch [CC FILTER]  
Used to select the optical filter (CC) of the camera.  
7
 
Controls and their Functions  
F Gain select switch [GAIN]  
Used to select the master gain of the camera. It changes in the order of 0dB )9dB  
)18dB )S1 (Super gain 1) )S2 )3dB )0dB.  
Note:  
For super gain setting, check with the camera menu.  
G Shutter select switch [SHUTTER OFF/STEP/SYNCHRO]  
Used to select the electronic shutter of STEP and SYNCHRO set on the camera.  
Note:  
For electronic shutter setting, check with the camera menu.  
H Indication change switch [CHECK]  
Used to change the indication item.  
I Indicator  
It indicates the F value of iris.  
J Master pedestal adjust volume [M-PED]  
Used to adjust the pedestal setting of Y (luminance) signal of the camera.  
K Lens iris auto/manual select switch [IRIS AUTO]  
Used to select the lens iris adjusting method.  
With the switch set to [AUTO], the lens is shifted to auto iris mode, and the iris is  
automatically adjusted according to the amount of light coming into the lens.  
With the switch set to [MANU], the lens iris can be moved in the range from close to  
open by turning the lens iris adjust VR (volume) L.  
When storing the lens iris in the preset position select switch 8 by using the preset  
memory switch 7, set to [MANU] mode. It does not work in [AUTO] mode.  
L Iris adjust volume [IRIS]  
When the lens iris auto/manual select switch K is set at [MANU], the lens iris can be  
moved in the range from close to open.  
When the lens iris auto/manual select switch K is set at [MANU], press the preset  
position select switch 8 to call the preset memory, then the lens iris position is set to  
the preset memory position irrespective of the VR (volume) position. After that, when  
the VR is turned, the lens iris returns to the value of VR.  
8
 
Controls and their Functions  
_Rear panel  
CAMERA I / F  
DC 12V IN  
MONITOR OUT  
G/L IN  
TALLY IN  
BREAKER  
P/T CONT  
Y
Pb  
Pr  
M
N
O
P
Q
R
S
M Camera connector [CAMERA I/F]  
Connected to the camera (AK-HC900P) with the attached cable.  
Pin No  
Signal  
Y signal output  
Pb signal output  
Pr signal output  
Sync signal input  
DC 12V  
Pin No  
Signal  
Y signal GND  
Pb signal GND  
Pr signal output  
Sync signal GND  
DC GND  
15 14 13 12 11 10 9  
8
1
2
3
4
5
6
7
8
7
6
5
4
3
2
1
9
10  
11  
12  
13  
14  
15  
Frame GND  
TXD (C)  
TXD (H)  
RXD (H)  
RXD (C)  
TXD: Data from camera to remote controller.  
RXD: Data from remote controller to camera.  
N Swivel stand control signal input connector [P/T CONT (RJ-45)]  
Connects the swivel stand control signal output of the pan-tilt control panel (AW-  
RP301).  
O Monitor signal output connector [Y/G, Pb/B, Pr/R] (BNCk3)  
Outputs the analog signal from the camera.  
The output can be changed to R, G, B/Y, Pb, Pr by the camera menu setting.  
P Synch signal input connector [G/L IN] (BNCk1)  
Inputs the sync signal to the camera. Input 3-value SYNC as the synch signal.  
Q Tally signal input connector [TALLY IN] (2-pin connector block)  
Connected to the tally connector from the system. When the HOT connector is at GND  
level, the tally LED is lighted.  
9
 
Controls and their Functions  
R Breaker [BREAKER]  
DC power breaker. The breaker operates to cut off the power in case of over-current.  
S DC12V input connector [DC12V IN] (XLR4-pin)  
Connects the AC adapter. We recommend that the AW-PS505P (option) is used.  
Pin No  
Signal  
4
1
2, 3  
4
GND  
–––  
1
3
2
12V  
10  
 
Controls and their Functions  
_Front panel  
ZOOM  
FOCUS  
REVERSE  
REVERSE  
NOR  
REV  
NOR  
REV  
T
U
T Zoom operation lever direction change switch [ZOOM REVERSE]  
Used to change the direction of the zoom operation lever.  
With this switch set at [NOR], when the zoom operation lever : is shifted to [TELE], the  
zoom operates in a telescopic mode, and when shifted to [WIDE], zooming is made in a  
wide angle mode.  
With this switch set to [REV], it can be operated in the opposite direction. Also, with this  
switch set to [REV], the operating direction does not match the indication on the panel.  
In that case, use the attached seal for proper indication.  
U Focus adjust direction change switch [FOCUS REVERSE]  
Used to change the direction of the focus adjust lever.  
With this switch at [NOR], when the focus adjust lever ; is shifted to [FAR], the focus is  
adjusted to a far distance, and when shifted to [NEAR], the focus is adjusted to a near  
distance.  
With this switch set to [REV], focusing can be made in the opposite direction. Also, with  
this switch set to [REV], the operating direction does not match the indication on the  
panel. In that case, use the attached seal for proper indication.  
11  
 
How to Connect  
Make the connection with power supply to the unit turned off.  
Use AW-PS505P (option) as the AC adapter for control panel.  
Use a swivel stand, AW-PH300A, AW-PH500, AW-PH600, and an adapter suited for  
the swivel stand.  
When no swivel stand is used, connect both of the motor-driven zoom lens iris control  
cable and remote (zoom/focus) cable to the camera. (see page 13)  
When a swivel stand is used, connect the iris control cable to the camera, and the  
remote (zoom/focus) cable to the swivel stand. (see the illustration below)  
For the connection system of each unit, refer to pages 14 to 16.  
Connect the motor-driven zoom  
To iris connector  
Iris control  
cable  
lens iris control cable to the  
camera, and the remote  
(zoom/focus control) cable to the  
swivel stand. If the motor-driven  
zoom lens remote (zoom/focus  
control) cable is connected to  
the camera, the lens cannot be  
controlled.  
B
R
E
A
K
E
/
R
Z
F
O
O
O
C
M
S
U
1
2
S
D
I
O
U
T
1
/
F
Remote  
(zoom/focus  
control) cable  
N D / E X T  
I N  
S D I  
L E N S E I / F  
I / F  
C A M E R A  
To lens interface  
connector  
D
C
I
1
2
V
CONTROL IN  
IP/RP  
N
1394  
C
S
OP  
G/L  
I
N
Pb OUT  
Pr  
OUT  
/
SDI  
Y/VIDEO  
OUT  
12  
 
How to Connect  
_Lens connection in the case of no swivel stand  
_How to mount the lens  
A lens of any makers can be used provided that it is a bayonet type (B4 mount) lens  
of 2/3 inch standard.*  
1 Turn the lens fixing ring knob counterclockwise and remove the lens mount cap.  
2 Mount the lens and completely secure it by turning the lens fixing ring knob  
clockwise.  
3 Connect the iris control cable to the lens connector.  
4 Connect the remote (zoom/focus control) cable to the zoom/focus connector on the  
rear panel.  
*Note that some lenses are uncontrollable with respect to zoom and focus function.  
B
R
E
A
K
E
/
R
Remote (zoom/focus control)  
cable  
Z
F
O
O
O
C
M
S
U
(Connect the cable to the swivel  
stand when used.)  
1
2
S
D
I
O
U
T
Iris control cable (to  
lens connector)  
Lens fixing ring knob  
13  
 
Multi-purpose digital camera control system configuration 1  
Remote (zoom/focus  
control) cable  
B
R
E
A
K
E
R
Z
F
O
O
O
M
/
C
U
S
HD-SDI  
Coaxial cable (5C-FB)  
2
S
D
I
O
U
T
1
/
F
D-SUB 15-pin  
Multi-purpose digital  
camera  
Remote  
control  
spec. lens  
AK-HC900P  
Multi-cable (17ft)  
AK-HDMLTCA05  
HD monitor  
AC adapter  
O
I
AW-PS505P  
Ext. sync signal (3-value SYNC)  
Camera Controller  
SCENE  
ON  
OFF  
OPERATE  
CAM  
POWER  
ALARM  
TEST  
PRE  
USER1  
USER2  
SD CARD  
MODE  
BAR  
AUTO  
WHITE  
BLACK  
TALLY  
GAIN  
BLACK  
MENU  
ON  
MENU  
4
ND FLTER  
1/16 1/32  
CC FLTER  
3200 4300 6300 CROSS  
1
0
1
/
4
PRESET  
3
DC power  
cable  
1
2
5
D-SUB 15-pin  
GAIN  
9dB  
SHUTTER  
OFF STEP SYNCRO  
18dB  
SPEED  
ZOOM  
FOCUS  
S1  
S2  
S3  
CHECK  
TELE  
FAR  
I
R
I
S
M-PED  
AUTO  
WIDE  
NEAR  
Camera controller  
AK-HRP900P  
14  
 
Multi-purpose digital camera control system configuration 2  
Remote  
control  
spec. lens  
B
R
E
A
K
E
/
R
Z
F
O
O
O
C
M
S
U
HD-SDI  
Coaxial cable (5C-FB)  
1
2
S
D
I
O
U
T
1
/
F
Multi-cable (17ft)  
AK-HDMLTCA05  
Multi-purpose digital camera  
AK-HC900P  
Remote  
(zoom/focus  
control) cable  
O
I
AC adapter  
AW-PS505P  
N D / E X T  
I N  
S D I  
L E N S E I / F  
I / F  
C A M E R A  
D
C
I
1
2
V
C
O
N
I
T
P
R
O
L
I
N
N
1394  
HD monitor  
/
RP  
C
S
OP  
G/L  
I
N
P
b
OUT  
P
r
/
SDI  
Y
/
VIDEO  
OUT  
OUT  
O
I
Swivel stand  
AW-PH300A  
AC adapter  
AW-PS505P  
Ext. sync signal (3-value SYNC)  
Camera Controller  
SCENE  
ON  
OFF  
OPERATE  
CAM  
POWER  
ALARM  
TEST  
PRE  
USER1  
USER2  
SD CARD  
Swivel stand control is  
possible for AW-  
PH500/PH600 as well.  
MODE  
BAR  
AUTO  
WHITE  
BLACK  
TALLY  
GAIN  
BLACK  
MENU  
ON  
MENU  
4
ND FLTER  
1/16 1/32  
CC FLTER  
1
0
1
/
4
3200 4300 6300 CROSS  
PRESET  
3
DC  
1
2
5
GAIN  
9dB  
SHUTTER  
18dB  
OFF STEP SYNCRO  
SPEED  
ZOOM  
FOCUS  
S1  
S2  
power  
cable  
S3  
CHECK  
TELE  
FAR  
I
R
I
S
M-PED  
AUTO  
WIDE  
NEAR  
Swivel stand controller  
AW-RP301  
Camera controller  
AK-HRP900P  
AC adapter  
AW-PS301  
15  
 
Multi-purpose digital camera control system configuration 3  
Remote  
control  
spec. lens  
Multi-cable (1.7ft)  
AK-HDMLTCA05  
B
R
E
A
K
E
/
R
Z
F
O
O
O
C
M
S
U
HD-SDI  
Coaxial cable (5C-FB)  
1
2
S
D
I
O
U
T
Interface adapter  
AK-HTF900P  
1
/
F
Multi-purpose digital camera  
AK-HC900P  
Remote  
(zoom/focus  
control) cable  
Trans-  
mission  
O
I
AC adapter  
AW-PS505P  
N D / E X T  
I N  
S D I  
Multi-cable (17ft)  
AK-HDMLTCA05  
L E N S E I / F  
I / F  
C A M E R A  
D
C
I
1
2
V
C
O
N
I
T
P
R
O
L
I
N
N
1394  
/
RP  
C
S
OP  
HD monitor  
G/L  
I
N
P
b
OUT  
P
r
/
SDI  
Y
/
VIDEO  
OUT  
OUT  
O
I
Swivel stand  
AW-PH300A  
O
I
AC adapter  
AW-PS505P  
AC adapter  
AW-PS300  
Camera Controller  
ON  
OFF  
SCENE  
USER1  
OPERATE  
CAM  
POWER  
ALARM  
TEST  
PRE  
USER2  
SD CARD  
Swivel stand control is  
possible for AW-  
PH500/PH600 as well.  
MODE  
BAR  
AUTO  
WHITE  
BLACK  
TALLY  
GAIN  
BLACK  
MENU  
ON  
MENU  
4
ND FLTER  
1/16 1/32  
CC FLTER  
3200 4300 6300 CROSS  
1
0
1
/
4
PRESET  
3
DC  
power  
cable  
1
2
5
GAIN  
9dB  
SHUTTER  
OFF STEP SYNCRO  
18dB  
SPEED  
TELE  
ZOOM  
FOCUS  
S1  
S2  
S3  
CHECK  
FAR  
I
R
I
S
M-PED  
AUTO  
WIDE  
NEAR  
Swivel stand controller  
AW-RP301  
Camera controller  
AK-HRP900P  
AC adapter  
AW-PS301  
16  
 
Communication Speed Setting  
The communication speed is factory-adjusted to 38.4Kpbs.  
In case it does not match the communication speed of multi-purpose camera AK-HC900P,  
the alarm LED is lighted. Remove the rear panel and change the DIP SW on the board  
and adjust it to the communication speed of the camera.  
Remove the  
screw and open  
the bottom  
plate, then DIP  
SW can be seen  
SW5 SW4 SW3  
in there.  
ON  
ON  
125Kbit/Sec  
1
2
3
3
3
4
4
4
1
2
3
4
SW3  
5
6
7
8
ON  
Change the  
38.4Kbit/Sec  
9600Kbit/Sec  
communication report  
by the combination of  
SW3 No.1 and No.2 on  
ROP CPU board.  
1
2
ON  
1
2
17  
 
Example of Rack Mount  
_How to rack-mount  
Install the main body on the rack as shown below.  
Remove the rack mount  
bracket screw when installing  
Rack mount bracket  
Coupler  
Attached  
screw  
Coupler  
fitting  
holes  
18  
 
Example of Rack Mount  
_How to change the rear panel position  
1 Remove the three screws on the  
3 Install the rear panel on the bottom with  
the three screws.  
bottom to remove the blank panel.  
Screw  
Screw  
CAMERA  
I
/
F
DC 12V IN  
Blank panel  
P/T CONT  
MONITOR OUT  
G/L IN  
TALLY IN  
BREAKER  
Y
Pb  
Pr  
2 Remove the three screws on the rear  
4 Install the blank panel on the rear side  
panel to remove the rear panel.  
with the three screws.  
Screw  
Screw  
CAMERA  
I
/
F
DC 12V IN  
P/T CONT  
MONITOR OUT  
G/L IN  
TALLY IN  
BREAKER  
Blank panel  
Y
Pb  
Pr  
* When installing, take care so that the internal wires are not caught by the panel.  
19  
 
Appearance and Dimensions  
(
): mm  
CAMERA  
I
/
F
DC 12V IN  
P/T CONT  
MONITOR OUT  
G/L IN  
TALLY IN  
BREAKER  
Y
Pb  
Pr  
Camera Controller  
SCENE  
ON  
OFF  
OPERATE  
CAM  
POWER  
ALARM  
PRE  
USER1  
USER2  
SD CARD  
MODE  
BAR  
AUTO  
TEST  
WHITE  
BLACK  
TALLY  
GAIN  
BLACK  
MENU  
ON  
MENU  
4
ND FLTER  
1/4 1/16 1/32  
CC FLTER  
3200 4300 6300 CROSS  
1
0
PRESET  
3
1
2
5
GAIN  
9dB  
SHUTTER  
OFF STEP SYNCRO  
18dB  
SPEED  
ZOOM  
FOCUS  
S1  
S2  
S3  
TELE  
FAR  
CHECK  
IRIS  
M-PED  
AUTO  
WIDE  
NEAR  
8-5/16z (210)  
ZOOM  
REVERSE  
FOCUS  
REVERSE  
NOR REV  
NOR  
REV  
20  
 
Specifications  
Power supply:  
DC +12V (XLR 4-pin connector)  
Power consumption: 5 W (camera controller only)  
1is the safety information.  
Swivel stand control input:  
System tally input:  
Switch function:  
Control signal (RJ-45 8P modular jack)  
Tally signal (2P connector block)  
Power control, preset memory, preset position select,  
speed polarity change, menu ON/OFF, menu operation,  
operation panel active, scene file select, mode select,  
auto white start, auto black start, ND filter select, CC  
filter select, gain select, shutter select, lens iris  
auto/manual select, indication change, zoom operation  
lever direction change, focus adjust direction change.  
Iris (lens iris), zoom, focus, R/B gain, master pedestal,  
R/B pedestal  
Adjusting function:  
Connection cable:  
Multi-cable 1 pc  
Cable max. extension distance: 33 ft (10m)  
Operating temperature range:  
Dimensions:  
32oF to 104oF (0oC to +40oC)  
8-5/16(W)k3-1/2(H)k6-15/16(D) inch  
(210k88k176 mm)  
Weight:  
Finish:  
Approx. 3.3 lbs (1.5kg)  
AV ivory coating (Munsell 7.9Y 6.8/0.8 approx. color)  
Weight and dimensions shown are approximate.  
Specifications are subject to change without notice.  
21  
 
Memo  
22  
 
Memo  
23  
 
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY  
UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA  
Executive Office:  
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201)348-7000  
EASTERN ZONE  
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201)348-7621  
Southeast Region:  
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835  
Central Region:  
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200  
WESTERN ZONE:  
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500  
Government Marketing Department:  
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840  
Broadcast PARTS INFORMATION & ORDERING:  
9:00 a.m. 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880  
Emergency after hour parts orders (800) 334-4881  
TECHNICAL SUPPORT:  
Emergency 24 Hour Service (800) 222-0741  
Panasonic Canada Inc.  
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010  
Panasonic de Mexico S.A. de C.V.  
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127  
Panasonic Sales Company  
Division of Matsushita Electric of Puerto Rico Inc.  
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300  
Printed in Japan  
VQT0A79  
@3  
F0902H  
 

Miller Electric Welding System MSC 2 User Manual
MTX Audio Speaker T4515 04 User Manual
Nokia Cell Phone 3310 User Manual
NXP Semiconductors Switch UM10317 User Manual
Oki Printer 20DX User Manual
Onkyo DVD Player DV SP504E User Manual
Oreck Vacuum Cleaner XL20R7RH User Manual
Panasonic Electric Shaver ER217 User Manual
Panasonic Printer KX P6100 User Manual
Paradyne Network Router 6212 I1 User Manual