Panasonic Network Card MAZWxxxHG Series User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
ESD Diodes  
MAZWxxxHG Series  
Silicon planar type  
For surge absorption circuit  
Features  
Package  
Two elements anode-common type  
Code  
SSSMini3-F2  
Pin Name  
1: Cathode 1  
2: Cathode 2  
3: Anode 1, 2  
Absolute Maximum Ratings Ta = 25°C  
Parameter  
Total power dissipation *  
Junction temperature  
Storage temperature  
Symbol  
Ptot  
Rating  
150  
Unit  
mW  
°C  
Internal Connection  
3
Tj  
150  
Tstg  
55 to +150  
°C  
Note) : Ptot = 150 mW achieved with a printed circuit board.  
*
1
2
Common Electrical Characteristics Ta = 25°C 3°C  
Parameter  
Zener voltage *  
Symbol  
VZ  
Conditions  
Min  
Typ  
Max  
Unit  
V
IZ  
Specified value  
Specified value  
Specified value  
Specified value  
Refer to the list of the  
electrical characteristics  
within part numbers  
Zener rise operating resistance  
Zener operating resistance  
Reverse current  
RZK  
RZ  
IZ  
IZ  
IR  
VR  
µA  
Note) 1. Measuring methods are based JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.  
2. Electrostatic breakdown voltage is 10 kV  
Test method: IEC1000-4-2 (C = 150 pF, R = 330 , Contact discharge: 10 times)  
 
3. : The temperature must be controlled 25°C for VZ mesurement.  
*
VZ value measured at other temperature must be adjusted to VZ (25°C)  
VZ guaranted 20 ms after current flow.  
Publication date: September 2007  
SKE00035AED  
1
 
This product complies with the RoHS Directive (EU 2002/95/EC).  
MAZWxxxHG Series  
SSSMini3-F2  
Unit: mm  
1.20 0.05  
0.30 +00..0025  
3
2
1
0.13 +00..0025  
0.20 +00..0025  
(0.4)  
(0.4)  
0.80 0.05  
SKE00035AED  
3
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Miele Washer W3622WPS User Manual
Moxa Technologies Switch NPort 6110 User Manual
MTX Audio Car Amplifier TC3001 User Manual
NordicTrack Home Gym NTBE01490 User Manual
Nostalgia Electrics Fondue Maker RHM 800 User Manual
Omnimount TV Mount 10238 User Manual
Optimus Cassette Player SCP 94 User Manual
Panasonic Car Stereo System C7113U User Manual
Panasonic Home Theater System SC PTX5 User Manual
Patterson Kelley Water Heater P K Compact User Manual