Panasonic Network Card 2SA2162G User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SA2162G  
Silicon PNP epitaxial planar type  
For general amplication  
Complementary to 2SC6036G  
Package  
Features  
Code  
Low collector-emitter saturation voltage VCE(sat)  
SSS-Mini type package, allowing downsizing of the equipment and automatic  
insertion through the tape packing  
SSSMini3-F2  
Marking Symbol: 2U  
Pin Name  
1. Base  
Absolute Maximum Ratings Ta = 25°C  
2. Emitter  
3. Collector  
Parameter  
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector current  
Symbol  
VCBO  
VCEO  
VEBO  
IC  
Rating  
–15  
Unit  
V
–12  
V
–5  
V
–500  
–1  
mA  
A
Peak collector current  
ICP  
Collector power dissipation  
Junction temperature  
PC  
100  
mW  
°C  
°C  
Tj  
125  
Storage temperature  
T
stg  
–55 to +125  
Electrical Characteristics Ta = 25°C±3°C  
Parameter  
Symbol  
Conditions  
Min  
–15  
–12  
–5  
Typ  
Max  
Unit  
V
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector-base cutoff current (Emitter open)  
Forward current transfer ratio  
VCBO IC = –10 mA, IE = 0  
VCEO IC = –1 mA, IB = 0  
VEBO IE = –10 mA, IC = 0  
V
V
ICBO  
hFE  
VCB = –10 V, IE = 0  
– 0.1  
680  
mA  
VCE = –2 V, IC = –10 mA  
270  
Collector-emitter saturation voltage  
Transition frequency  
VCE(sat) IC = –200 mA, IB = –10 mA  
–250  
mV  
MHz  
fT  
VCB = –2 V, IE = 10 mA, f = 200 MHz  
200  
4.5  
Collector output capacitance  
Cob  
VCB = –10 V, f = 1 MHz  
pF  
(Common base, input open circuited)  
Note) Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
Publication date : May 2007  
SJC00384AED  
1
 
This product complies with the RoHS Directive (EU 2002/95/EC).  
SSSMini3-F2  
Unit: mm  
1.20 0.05  
0.30 +00..0025  
3
2
1
0.13 +00..0025  
0.20 +00..0025  
(0.4)  
(0.4)  
0.80 0.05  
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Miele Washer W 2809i User Manual
Multiquip Landscape Lighting MB1000 User Manual
Napoleon Fireplaces Indoor Fireplace GDI30 User Manual
NETGEAR Network Router RT328 User Manual
Nintendo Video Game Controller 96071 User Manual
Nortel Networks Telephone NN10042 116 User Manual
Oregon Scientific Radar Detector MR238 User Manual
Panasonic Blu ray Player BDP 140 User Manual
Panasonic Microwave Oven NN G354 User Manual
Patton electronic Home Theater Server 1195 User Manual