Oregon Scientific Clock Radio RM832A User Manual

Thank you for purchasing the RM832A Radio Controlled Travel Alarm Clock  
with HiGloTM backlight! Your RM832A is an always-accurate Radio  
Controlled clock combining form and function in a small compact  
take-everywhere size.  
RADIOCONTROLLED  
TM  
TRAVEL CLOCK WITH Higlo  
Your RM832A features a daily alarm, calendar, day-of-the-week display,  
electroluminescent HiGloTM backlight, snooze alarm, automatic adjustment  
for Daylight Savings Time and ExactSetTM technology.  
BACKLIGHT  
Radio Controlled clocks receive signals from the U.S. Atomic Clock, one of  
the world’s most accurate timepieces.For information about the National  
Institute of Standards and Technology and the U.S. Atomic Clock, visit the  
MODEL : RM832A  
1. ACTIVATING THE CLOCK  
The RM832A requires 2 “AAA” size batteries .The RM832A will seek the  
signal from the US Atomic Clock once the batteries are activated. (See Signal  
Reception) To activate the batteries:  
R
A
D
I
O
C
O
N
T
R
O
L
L
E
D
1. To open the battery compartment, A slide the compartment door towards the  
bottom of the clock.  
2. Remove the two protective plastic strips from the batteries and slide the  
battery compartment door back into place over the battery compartment.  
3. Slide the B Lock to the unlocked position.  
IMPORTANT: To set user-selections and settings the RM832A must be in the  
unlocked position. Locking is recommended during transit to prevent settings  
from being accidently changed.  
NOTE: The RM832A features a low battery warning icon. This icon [  
]
will appear when batteries need replacing.To replace batteries: remove the  
battery compartment door, remove the old batteries, insert fresh batteries into  
the compartment with the polarities in the direction as shown inside the  
compartment, and slide the battery compartment door back into place.  
2. SIGNAL RECEPTION ICON AND TIME ZONE  
With reception of the US Atomic Clock signal, an icon designating the  
C strength of signal reception will be displayed. (See Signal Reception) With  
the successful reception of the signal, the RM832A will automatically select  
the correct US time zone and the corresponding time and date. To view or  
manually select another time zone and corresponding time and date after  
initial setting by the US Atomic Clock:  
ZONE  
1. Using a single-press method, press D [ZONE] to advance through the  
zones. Zones are identified by the letters: “P” Pacific; “M” Mountain; “C”  
Central and “E” Eastern.  
LOCK  
2. The letter representing the time zone selected will be displayed immediately  
under the signal strength icon.  
3. ALARM FUNCTIONS  
Setting the Alarm:  
1. Press and hold E [DATE/ALARM] until the “hour” segment begins to  
flash. While the “hour” is flashing, press the F[s] to set the desired hour.  
NOTE: There are AM and PM designations.  
2. When the desired hour is reached, press E [DATE/ALARM] again, and  
the “minutes” segment will begin to flash. Press the F[s] to set the desired  
minutes.  
3. Press E [DATE/ALARM] once more to exit the alarm setting mode.  
Turning the Alarm ON and OFF:  
1. Pressing the G [ON/OFF] activates and disables the daily alarm.  
2. When the alarm is active, the bell icon H [ ] will be displayed.  
3. To turn the alarm off, press the G [ON/OFF]. When the alarm is disabled,  
no bell icon will show.  
4. To temporarily deactivate the alarm, press E [DATE/ALARM]. The alarm  
remain active and will sound again in 24-hours.When this feature is  
activated, I [(( • ))] will be displayed.  
Snooze and Backlight Features:  
1. Pressing  
J
[
T
O
U
C
H
] while the alarm is sounding will  
S w in g-up Table S tand  
activate the 8-minute snooze feature . After 8-minutes the alarm will sound  
again.  
2. Pressing [  
T
O
U C  
H
] will also activate the backlight for  
5-seconds.  
4 USER SELECTIONS  
Manually Setting: time, year, month, date & Language  
NOTE: It is highly unlikely you should ever have the desire (or need) to  
manually set the clock time, year, month or date of RM832A Travel Clock.  
However, in the event this becomes necessary please review the following.  
Setting the Time  
1) Press and hold K [MODE] button for at least three seconds. The “Hour”  
segment of the clock time will begin flashing  
2) While the “hour” segment is flashing press the E [DATE/ALARM] button  
to set the desired hour time (Please note the AM/PM designation)  
3) When the desired hour times reached press the K [MODE] button again.  
The “Minutes” segment of the clock time will begin flashing.  
4) While the “Mi” segment is flashing press the F [s] button to set the  
desired minute.  
5) When the desired minutes time is reached. Briefly press the K [MODE]  
button five more times to exit the clock time set mode.  
Important: As soon as any manual change in the clock time is made, there  
is a loss of the signal strength indicator from the display.  
Setting the Year Month and Date  
1) Press and hold K [MODE] button for at least three seconds. The  
“Hour”segment of the clock time will begin flashing.  
2) Briefly press the MODE button and the “Minutes” segment will begin flashing.  
3) Briefly press the K [MODE] button once more. The clock time will disappear  
and be replaced by a flashing year (Ex. 1995). This is the year set mode.  
 

Miller Electric Welder D 74DX User Manual
Miller Electric Work Light MC 80 User Manual
Milwaukee Work Light B51A User Manual
National Instruments Switch Low Cost Multifunction I O Board for ISA Lab PC+ User Manual
NEC IP Phone IP3AT 8WVAUSTRALIA User Manual
Olympus Microcassette Recorder VN 5000 User Manual
Omron Healthcare Blood Pressure Monitor HEM 711 User Manual
Panasonic Air Conditioner CW XC55HU User Manual
Panasonic PDAs Smartphones CF P1Series User Manual
Panasonic Universal Remote AJ G User Manual