Oregon Scientific Clock Radio BARM699A User Manual

2. Weather forecast  
To enable and force a signal search:  
3. Preset radio station number  
4. AM / FM station; radio frequency in MHz or KHz and  
volume level  
Press and hold TUNING / SET  
for 2 seconds.  
To disable the signal reception:  
5. Radio-controlled clock reception icon  
6. 12-hour clock  
Press and hold TUNING / SET  
for 2 seconds.  
flashes when it is searching for the atomic clock  
signal and disappears when it is disabled.  
7. Indoor temperature display icon  
8. Channel number and sensor reception status  
9. Sensor low battery warning  
10. Outdoor temperature reading  
11. Maximum / minimum outdoor temperature reading  
12. Main unit low battery warning  
13. Indoor temperature reading  
14. Maximum / minimum indoor temperature reading  
15. Sleep function is activated  
16. Alarm is displayed  
Touch-Control AM/FM Atomic Weather  
Clock with Dual Alarm  
CLOCK  
Model: BARM699A  
For best results:  
To manually set the clock make sure the clock signal  
reception is disabled.  
Place the sensor out of direct sunlight and  
moisture.  
USER MANUAL  
INTRODUCTION  
Thank you for selecting the Oregon ScientificTM Touch-  
Control AM/FM Atomic Weather Clock with Dual  
Alarm (BARM699A). The main unit can support up  
to 3 sensors. To purchase additional sensors, please  
contact your local retailer.  
Do not place the sensor more than 30 meters (100  
feet) from the main (indoor) unit.  
To manually set the clock:  
1. Press and hold CLOCK for 2 seconds.  
2. Press TUNING / SET  
settings.  
3. Press CLOCK to confirm.  
4. The setting sequence is: US time zone, 12 / 24  
hour format, hour, minute, year, day / month format,  
month, day, and display language.  
Position the sensor so that it faces the main (indoor)  
unit, minimizing obstructions such as doors, walls,  
and furniture.  
/
to change the  
17. Beep alarm is set  
18. Radio alarm is set  
19. US time zone, weekday or seconds  
20. Time, alarm and date  
Place the sensor in a location with a clear view to  
the sky, away from metallic or electronic objects.  
Position the sensor close to the main unit during cold  
winter months as below-freezing temperatures may  
affect battery performance and signal transmission.  
NOTE Please keep this manual handy as you use  
your new product. It contains practical step-by-step  
instructions, as well as technical specifications and  
warnings you should know about.  
REMOTE SENSOR  
NOTE The US time zone options are Pacific (PA),  
Mountain (MO), Central (CE) and Eastern (EA).  
The transmission range may vary depending on many  
factors. You may need to experiment with various  
locations to get the best results.  
1. LED status indicator:  
Blinks red during data  
1
NOTE The language options are (E) English, (F)  
transmission  
2. Ventilation duct  
French, (D) German, (I) Italian, and (S) Spanish.  
OVERVIEW  
FRONT VIEW  
Standard Alkaline batteries contain significant  
amounts of water. Because of this they will freeze  
in low temperatures of approximately -12°C (10°F).  
2
To switch the clock display:  
Press CLOCK to toggle between:  
1
1
Disposable Lithium batteries have  
a
much lower  
Clock with seconds  
Clock with weekday  
Calendar  
3
threshold for temperature with an estimated freezing  
range of below -30°C (-22°F).  
5
1. Wall mount  
2. Battery compartment  
3. Battery door  
4. Table stand  
2
3
6
Wireless ranges can be impacted by a variety of factors  
such as extremely cold temperatures. Extreme cold  
may temporarily reduce the effective range between the  
sensor and the base station. If the unit’s performance  
fails due to low temperature, the unit will resume proper  
functioning as the temperature rises to within the  
normal temperature range (i.e. no permanent damage  
will occur to the unit due to low temperatures).  
ALARM  
4
To set the alarm:  
1. Press ALARM to view the alarm.  
the display.  
will show on  
7
5. CHANNEL switch  
2
5
2. Press and hold ALARM for 2 seconds.  
4
3. Press TUNING / SET  
/
to change the hour,  
minute, beep or radio alarm. If you select the radio  
alarm, press AM / FM and STATION to select the  
band and station respectively.  
GETTING STARTED  
POWER  
SENSOR DATA TRANSMISSION  
The reception icon shown in the outdoor temperature  
area shows the status.  
1. SLEEP / SNOOZE: Activate snooze; set the sleep  
timer  
2. RADIO ON / OFF: Turn radio ON / OFF  
3. STATION:Toggle between 16 preset radio channels;  
save a channel  
4. VOLUME  
5. CLOCK: Change setting / display  
6. AM / FM: Toggle between AM and FM  
7. TUNING / SET  
4. Press ALARM to confirm.  
Plug adapter into main unit.  
To activate or deactivate the alarm:  
Press ALARM when in the alarm display.  
or  
ICON  
DESCRIPTION  
appears when the alarm is set.  
Main unit is searching for  
the sensor(s)  
A channel has been found  
and signal is being  
received  
/
: Increase / decrease volume  
To silence the alarm:  
Press SNOOZE to silence it for 8 minutes.  
/
: Increase / decrease  
OR  
setting; activate / deactivate clock reception signal;  
change radio frequency  
Press any key except SNOOZE to turn the alarm off  
and activate it again after 24 hours.  
and “- -“  
(Outdoor temperature  
area)  
The sensor cannot be found.  
Search for the sensor or  
check the battery  
NOTE This product may malfunction when radio  
interference appears on the AC power line. The unit will  
revert to normal operation when interference stops.  
BACK VIEW  
NOTE  
or  
flashes when snooze is activated.  
To search for a sensor:  
WEATHER FORECAST  
Simultaneously, press and hold MEM and CHANNEL  
for 2 seconds.  
1
2
4
NOTE Install the remote sensor battery and plug in the  
main unit. Press RESET after each battery change. Do  
not use rechargeable batteries. It is recommended that  
you use alkaline batteries with this product for longer  
performance.  
This product forecasts the weather for the next 12 to 24  
hours within a 19-31 mile (30-50 km) radius, with 70 to  
75 percent accuracy.  
NOTE The sensor LED flashes when data is being  
sent to the main unit. If the sensor signal is still not  
found, check the battery, obstructions, and remote unit  
location.  
SUNNY PARTLY CLOUDY CLOUDY RAINY  
shows when battery is low.  
LIGHT TOUCH KEY  
5
6
UNIT  
Main  
Remote  
LOCATION  
Indoor temperature area  
Outdoor temperature area  
3
TEMPERATURE  
The touch keys used in this product have a key lock  
function that prevents accidental changes to user  
settings. When the clock keys have not been used in  
the last minute, the key lock function is automatically  
activated. Press any key once to disable the key lock  
function and then operate the clock as usual.  
To change the temperature measurement unit:  
Press °C / °F on the bottom of the unit.  
1. MEMORY: View current, maximum and minimum  
temperature  
REMOTE SENSOR  
2. CHANNEL: Switch remote sensor display  
3. Adapter socket  
4. ALARM: View alarm status; set alarm  
5. °C / °F: Select temperature unit °C / °F  
6. RESET: Reset unit to default settings  
To view outdoor sensor(s) temperature readings:  
Press CHANNEL.  
The sensor collects temperature readings approx. every  
40 seconds and sends them to the main unit. The main  
unit can collect data from up to 3 sensors.  
shows which remote sensor’s data you are  
viewing.  
CLOCK RECEPTION  
is permanently displayed in the indoor  
temperature area.  
This product is designed to synchronize its date and  
time automatically once it is within range of the WWVB-  
60 signal from the atomic clock in Boulder, Colorado.  
To set up the sensor:  
1. Slide open the battery door.  
2. Insert the battery, matching the polarity (+ / -).  
3. Select a channel. Make sure you use a different  
channel for each sensor.  
LCD  
To auto-scan between sensors:  
Press and hold CHANNEL for 2 seconds. Each sensor’s  
data is displayed for 3 seconds.  
7
8
9
The sensor collects the radio signals whenever it is  
within 3219 km (2000 miles) of a signal.  
1
10  
11  
2
To end auto-scan:  
Press CHANNEL or MEMORY.  
NOTE Initial reception takes 2-10 minutes for first set  
up or when RESET is pressed. Once complete, the  
reception icon will stop blinking. If the signal is weak, it  
can take up to 24 hours to get a valid signal.  
12  
13  
14  
15  
16  
17  
3
4
5
To toggle between current, minimum and maximum  
records for the selected sensor:  
Press MEMORY repeatedly.  
6
18  
RECEPTION SIGNAL  
19  
STRONG  
WEAK  
NO SIGNAL  
To clear the records:  
4. Close the battery compartment.  
5. Secure the sensor in the desired location using the  
wall mount or table stand.  
20  
Select the channel to clear the memory, then press and  
hold MEMORY for 2 seconds.  
1. Ice warning  
BARM699A_EN_R5.indd  
1
2/17/06 2:04:50 PM  
 

Miele Ice Maker 09 920 570 User Manual
Miglia Technology Computer Drive VideoExpress Converter User Manual
NAD Stereo Amplifier C272 User Manual
NeumannBerlin Microphone KMS 140 User Manual
New Buck Corporation Fan 91 User Manual
Nokia Cell Phone 3285 User Manual
Oregon Scientific Clock EMR801 User Manual
Palm Cell Phone PDA CentroTM Smart Device User Manual
Panasonic Scanner KV S5055C User Manual
ParaBody Home Gym 908101 ST User Manual