Oreck Sander LB8005 User Manual

S I M P L Y  
A M A Z I N G ™  
USERS GUIDE  
LOW BOY  
INDUSTRIAL  
FLOOR MACHINE  
LB8005  
•IMPORTANT•  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Warranty  
• Operating Instructions  
• Trouble Diagnosis  
• Accessories  
 
IMPORTANT:  
Warranty  
Where Necessary for Plug to be Fitted  
ORECK MANUFACTURING COMPANY: (ORECK gives you the  
following limited warranty for this product only if it was originally  
purchased for use, not resale, from ORECK or an ORECK Authorized  
Retail Dealer.)  
The wires in this mains lead are coloured in accordance with the  
following code:  
Blue: Neutral  
Brown: Live  
Green: Earth  
ORECK will repair or replace, free of charge, to the original purchaser,  
any part which is found to be defective in material or workmanship  
within one (1) year of the date of original purchase.  
As the colours of the wires in the mains lead of this appliance may not  
correspond with the coloured markings identifying the terminals in your  
plug, proceed as follows;  
PAD DRIVER, CARPET BONNET, LAMBS WOOL BONNET,  
BRUSHES, PADS and other parts subject to normal wear are not  
covered by this limited warranty.  
The wire which is coloured Blue must be  
13 AMP FUSE  
E
GREEN  
connected to the terminal which is  
marked with the letter N or coloured  
Black.  
This limited warranty does not apply to any part subjected to accident,  
abuse, or alteration, misuse, damage caused by fire or act of God, the  
use of voltages other than indicated on the serial number plate of this  
product or service of this product by other than ORECK or an ORECK  
Factory Authorized Service Center.  
The wire which is coloured Brown must  
be connected to the terminal which is  
marked with the letter L or coloured Red.  
L
N
Green is to be connected to the earth pin  
of the 3 pin plug.  
BROWN  
CORD CLAMP  
ORECK does not authorize any person or representative to assume or  
grant any other warranty obligation with the sale of this product.  
BLUE  
The wire which is coloured Green must  
be connected to the terminal which is  
marked with the letter E.  
ORECK’S limited warranty is valid only if you retain proof of purchase  
from ORECK or an ORECK Authorized Retail Dealer for this product. If  
you purchase this product from any other source, your purchase is “AS  
IS,” which means ORECK grants you no warranty, and that you, not  
ORECK, assume the entire risk of the quality and performance of this  
product, including the entire cost of any necessary servicing or repairs  
of any defects.  
If a 13 amp plug is fitted, fit a 13 amp fuse.  
Low Boy Model LB8005 is  
intended for Commercial Use.  
ORECK’S liability for damages to you for any costs whatsoever arising  
out of this statement of limited warranty shall be limited to the amount  
paid for this product at the time of original purchase, and ORECK shall  
not be liable for any direct, indirect, consequential or incidental  
damages arising out of the use or inability to use this product.  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not  
apply to you.  
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,  
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN  
DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,  
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS  
PERIOD.  
Some states do not allow limitations on the duration of implied  
warranties, so the above limitation may not apply to you.  
This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
3
 
To Guide the Machine  
Operating Instructions  
Hold the handle with both hands and push with the palms of your hands  
to move in the forward direction, then cup your hands and pull to bring  
back. The design of the machine eliminates the fatigue associated with  
controlling other floor machines.  
WARNING: Unplug cord from electrical  
outlet before servicing and when leaving  
unattended.  
Care of your Oreck Low Boy Floor Machine  
This is a precision machine. Dropping unreasonable bumping or rough  
handling may result in damage. Remove brushes after use. The bristles  
may be damaged due to the weight of the machine. Store your machine  
in the upright position. After each use, remove wax or cleaning  
solutions. After sanding, blow sawdust off motor and locking  
mechanism.  
To Operate:  
IMPORTANT - Always wear shoes  
when using your Low Boy.  
Raise the handle pin release with foot.  
Lubrication: With the handle in its  
lowest position, periodically place one  
drop of oil (3-in-One) on the thrust  
bearings.  
Lean handle back. While handle is  
released and with both hands on  
handle grips, squeeze the ON/OFF  
lever located on the right grip to turn  
on.  
THRUST BEARINGS  
Troubleshooting Guide  
WARNING: Unplug cord from electrical  
outlet before servicing.  
To Attach the Drive Pad Holder or  
Brush:  
PROBLEM  
POSSIBLE SOURCE  
AREAS TO CHECK  
Lay the machine on its back to reveal  
the bottom pan. Align the indentations  
in the pad holder with the brackets  
around the bottom pan. Place your  
hands on opposite sides of the pad  
holder and using the heel of your  
hands, push the pad holder onto the  
pan.  
Not plugged in  
properly.  
Be sure cleaner is  
firmly plugged into  
wall outlet.  
FLOOR MACHINE  
WILL NOT RUN  
No electricity in wall  
outlet.  
Check electrical  
source–fuse or  
circuit breaker.  
Motor circuit  
breaker has  
tripped.  
Reset motor circuit  
breaker.  
Use the included key to rotate the  
swing arms clockwise to lock the pad  
holder to the bottom pan. Place a pad  
on the floor and position the machine  
so that as the handle is raised the pad  
holder is centered on the pad.  
HANDLE WILL NOT  
UNLOCK  
Locking pin needs  
cleaning  
Clean locking  
mechanism  
HANDLE IS HARD TO  
RAISE OR LOWER  
Lower handle pivot  
bearings need oiling  
Oil pivot bearings.  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
To Attach the Pad:  
Lay the floor machine on its back with  
the handle lying on the floor. This  
exposes the brush holder pan. Just  
place the pad over the round brush  
holder pan making sure it is in place.  
CALL CUSTOMER SERVICE HOT LINE  
0800 67 68 69  
Whenever calling, please be sure to have your model and serial  
number from data plate.  
CAUTION: NEVER put the pad on the  
machine by placing it on the floor and  
moving the running machine over it, or  
placing the machine over the pad and  
then starting the motor.  
53307-01 REV A  
8/01 ECN# R-6062  
© 2001 Oreck Holdings, LLC. All Rights Reserved. All word marks, logos, regestered trademarks and product configurations are  
owned and used under the authorization of Oreck Holdings, LLC.  
4
 

NEC Flat Panel Television LCD19WV User Manual
Nikon Camera Lens 1910 User Manual
Nortel Networks Computer Hardware 5380 User Manual
Nostalgia Electrics Beverage Dispenser CSD 250 User Manual
Onkyo Stereo System TX 8222 User Manual
Onkyo Stereo System TX DS656 User Manual
Oregon Scientific Surge Protector ESD200 User Manual
Packard Bell Laptop H5 User Manual
Panasonic Air Conditioner CS KE18NB4UW User Manual
Parkside Sander PDS 290 AI User Manual