Onkyo Stereo Receiver HT R393 User Manual

HT-R393  
AV RECEIVER  
Basic Manual  
Advanced Manual found here  
E
n
 
Connections  
Step 1:  
TV  
Personal computer  
HDMI  
IN  
HDMI  
OUT  
HDMI cable  
To use the ARC function, connect to the ARC  
compatible HDMI jack of the TV and make an  
appropriate setting on the unit. See the section  
3 "HDMI Setup" of "Step 2: Setting Up".  
HDMI  
OUT  
HDMI  
OUT  
HDMI  
OUT  
Blu-ray Disc/  
DVD player  
HDMI  
OUT  
Game console  
Set-top box/Digital  
video recorder, etc.  
Satellite/Cable  
set-top box, etc.  
zꢀ  
Connection with a TV not supporting ARC  
For how to make settings, see the Advanced Manual.  
Connecting the TV and players  
1
To connect the TV and the unit, connect the HDMI OUT jack  
of the unit and the HDMI IN jack of the TV using an HDMI  
cable. With this connection, it becomes possible to display the  
setting screen of the unit on the TV or transmit video/audio  
signals from the player to the TV. If your TV supports ARC  
(Audio Return Channel), it is possible to play the TV sound  
with the AV receiver's speakers with this connection only. If  
your TV does not support ARC, you need, in addition to the  
HDMI OUT jack connection, a digital optical cable connection  
between the digital audio out optical jack of the TV and the  
DIGITAL IN OPTICAL jack of the unit or an analog audio  
(RCA) cable connection between the audio output jack of the  
TV and the TV/CD analog audio input jack of the unit.  
TV  
AUDIO  
OUT  
DIGITAL  
OPTICAL  
OUT  
Important: The power cord must be connected only after all  
other connections are completed.  
HDMI Cable Connection  
The unit has many HDMI jacks on its rear panel and each  
of them corresponds to an input selector button of the same  
name on the front panel. For example, a Blu-ray Disc player  
will be connected to the IN 1 jack and the BD/DVD button  
on the front panel will be used to listen to the playback  
sound (if the player is CEC compliant, input will be switched  
automatically). If you add another Blu-ray Disc player, you  
can use any other jack than IN 1. It is possible to change  
assignment of the input jacks and input selector buttons.  
Select an appropriate connection  
¼ꢀ  
for your TV.  
The unit supports the HDMI Through function that allows  
transmission from players to the TV even if the unit is in  
standby.You have to modify the settings to enable the input  
selection link with CEC compliant device, connection with  
ARC compatible TV, and HDMI Through function. See the  
section 3 "HDMI Setup" of "Step 2: Setting Up".  
 
3
Step 1: Connections  
rꢀ To play 4K or 1080p video, use the high speed HDMI  
cable.  
Audio signal connection  
1 Digital connection: Use a digital optical cable  
(OPTICAL) or digital coaxial cable (COAXIAL) for  
connection with a player.  
Connecting Components without HDMI  
Digital optical cable (OPTICAL)  
If your AV component does not have HDMI jack, use an  
available jack of your component for cable connection with  
this unit. Just as the HDMI jacks, other jacks on this unit have  
a preassigned input selector button on the front panel. See  
the name of the input selector button shown with the jack  
when connecting the device.  
As the digital in optical jack of the unit has a  
¼ꢀ  
cover, push in the cable against the cover as it is  
turned inside.  
Digital coaxial cable (COAXIAL)  
2 Analog connection: Use an analog audio (RCA) cable  
for connection with a player.  
To enjoy multi-zone playback of audio of a CD player  
or such other player without HDMI output jack, you  
need to use the analog audio (RCA) cable to connect  
the corresponding jacks of the player and this unit. For  
details on the multi-zone function, see the section 6  
"Using the multi-zone function" of "Step 3: Playing Back".  
1
3
4
Analog audio (RCA) cable  
Video signal connection  
3 Use a component video cable to connect a TV  
with component video input jacks and a player with  
component video output jacks.  
rꢀ When a component video cable is used for  
connecting the unit and the player, the unit and TV  
must also be connected with a component video  
cable.  
Component video cable  
Its transmitted video has higher quality than that  
¼ꢀ  
of composite video cable.  
2
Use a composite video cable to connect a TV with  
composite video input jack or a player with composite  
video output jack.  
rꢀ When a component video cable is used for  
connecting the unit and the player, the unit and TV  
must also be connected with a component video  
cable.  
4
If you connect a turntable which does not have a built-  
in audio equalizer, you need to install an external audio  
equalizer between the unit and the turntable.  
Composite video cable  
 
4
Step 1: Connections  
2
Front R  
1
Front L  
Connecting speakers  
2
3
Center  
Important: The power cord must be connected only after all  
other connections are completed.  
12  
3
6
45  
Front speakers  
Center speaker  
1 2  
3
Surround speakers  
Subwoofer  
4 5  
6
rꢀ The position and size of the speakers is an image.  
rꢀ Only one subwoofer can be connected.  
rꢀ To use the ZONE function, refer to the section 6 "Using  
the multi-zone function" of "Step 3: Playing Back".  
6
Passive type  
subwoofer  
5
Surround R  
4
Surround L  
It is ideal to install the front speakers and center speaker  
at the height not too far from that of the screen. As for the  
surround speakers, it is recommended to install at the  
position slightly backward of the listening position and  
higher than the listener's ears, since it is preferable to  
obtain a diffused sound rather than a direct sound. As a  
bass sound reproduced by subwoofer is less directional,  
it is possible to place it at any position. Consider the best  
installation position where a bass sound can be clearly  
heard by listening to actual playback.  
3/8"-1/2" (10-12 mm)  
connection is wrong, a bass sound may become poor due to  
reverse phase. The levers of positive (+) speaker terminals  
are color-coded. Also, the supplied speaker cables are color-  
coated to help correct connection. The colored cables are  
positive (+) cables. Connect a cable to a terminal in the  
same color as the cable. Do not connect a subwoofer with  
built-in power amplifier to the subwoofer terminals of this  
unit.  
Importantꢄꢀ%QPPGEVꢀURGCMGTUꢀYKVJꢀꢂꢀŝꢀVQꢀꢁꢂꢀŝꢀKORGFCPEGꢃꢀ  
Using a speaker with less impedance than the supported  
value may result in failure.  
rꢀ The speaker setting is 5.1 ch at the time of purchase.  
Change the setting when you use a configuration other  
than 5.1 ch.  
Cut and remove the plastic coating from the end of the  
speaker cable, twist the core and connect it to the terminal.  
Make correct connection between the unit's jacks and  
speaker's jacks (+ to + and - to -) for each channel. If  
rꢀ Short-circuiting the + cable and - cable or contacting the  
 
5
Step 1: Connections  
cable core to the rear panel of the unit may cause failure.  
Also do not connect two or more cables to one speaker  
jack or one speaker to several jacks.  
Headphones connection  
Other connections  
3
%QPPGEVꢀUVGTGQꢀJGCFRJQPGUꢀYKVJꢀCꢀUVCPFCTFꢀRNWIꢀꢅꢁꢆꢇ|KPEJꢀ  
QTꢀÔꢀꢂꢃꢈ|OOꢉꢀVQꢀVJGꢀ2*10'5ꢀLCEMꢃꢀ5QWPFꢀHTQOꢀVJGꢀ  
speakers will be off while you are using the headphones.  
rꢀ If you selected any other listening mode than Stereo,  
Mono and Direct, connecting headphones will switch the  
listening mode to Stereo.  
AM/FM antenna connections  
Connect the antennas to listen to AM/FM broadcast. When  
listening to the broadcast for the first time, adjust the  
antenna position and orientation to get the best reception.  
AM loop antenna (supplied)  
Indoor FM antenna  
(supplied)  
Fix with a tack on  
the wall.  
(North American model)  
(European and Asian  
models)  
Assemble the AM loop antenna (supplied).  
 
6
Setting Up  
Step 2:  
Changing speaker configuration  
Turning the power on  
1
After pressing RCV, press HOME on the remote  
controller.  
1.  
Connect the power cord to the outlet. Press ON/  
z
With the cursor, select "Setup", and press ENTER.  
Select "5. Sp Config" with the cursor, and press  
ENTER.  
2.  
3.  
STANDBY on the main unit or RECEIVER on the remote  
z
controller to turn the unit on or to standby mode.  
d c  
/ buttons and set "None" for the  
Move the cursor with  
speaker ("No" for subwoofer) which is not connected.  
Press HOME to save the changed setting and close the  
menu screen.  
rꢀ This setting cannot be changed if headphones are  
connected or audio is output from the speakers of the TV.  
z Operation:You can set up by viewing the guidance  
displayed on the TV screen. To display the guidance, you  
need to make HDMI connection between the unit and  
TV. Select the item with the cursor buttons of the remote  
controller and press ENTER to confirm your selection. To  
return to the previous screen, press RETURN. To return to  
the Home menu, press HOME.  
rꢀ When the unit is turned on, a large instantaneous current  
may flow affecting functionality of the computer and other  
devices. It is recommended to use a separate outlet from  
that for the computer or such other sensitive devices.  
Setting speaker distance  
After pressing RCV, press HOME on the remote  
controller.  
Select "Setup" with the cursor, and press ENTER.  
Select "6. Sp Distance" with the cursor, and press  
ENTER.  
1.  
Making speaker setting  
2
2.  
3.  
The speaker configuration of this unit is set to 5.1 ch by  
default. To use the unit in a different environments such as  
a configuration without center speaker, surround speaker  
or subwoofer, you need to make settings for each of the  
following items.  
rꢀ If the settings do not match the actual speaker  
configuration, audio playback may not be performed  
correctly. Check your speaker configuration and make  
correct settings.  
 
7
Step 2: Setting Up  
d c  
buttons and set the distance  
Move the cursor with  
/
HDMI Through  
HDMI Setup  
from each speaker to the listening position. Press HOME to  
save the changed setting and close the menu screen.  
rꢀ This setting cannot be changed if headphones are  
connected or audio is output from the speakers of the TV.  
rꢀ The distance of speakers cannot be changed if "No" or  
"None" is set for them in "Sp Config".  
3
The function allows transmission from players to the TV  
even if the unit is in standby. Setting the HDMI CEC (RIHD)  
setting mentioned above to "On" can enable this setting  
automatically. It is also necessary to make the HDMI linked  
system setting on the TV. See the TV's instruction manual  
for details.  
The unit supports the linked system function such as power  
on/off link when connected via HDMI cable with a CEC  
(Consumer Electronics Control) compliant TV or player.You  
need to change the initial setting to use the linked system  
function, HDMI Through function and ARC (Audio Return  
Channel) function.  
rꢀ Although enabling the HDMI Through function increases  
power consumption during standby.  
Adjusting volume level of speakers  
z Operation:You can set up by viewing the guidance  
displayed on the TV screen. To display the guidance, you  
need to make HDMI connection between the unit and  
TV. Select the item with the cursor buttons of the remote  
controller and press ENTER to confirm your selection. To  
return to the previous screen, press RETURN.  
After pressing RCV, press HOME on the remote  
controller.  
With the cursor, select "Setup", and press ENTER.  
Select "7. Level Cal" with the cursor, and press  
ENTER.  
1.  
ARC (Audio Return Channel)  
2.  
3.  
Simple connection to the ARC compatible TV using a  
single HDMI cable allows to listen to the TV sound from the  
speakers connected to the unit. To use the ARC function,  
connect the unit to the ARC compatible HDMI jack of the  
TV. Then, set the HDMI CEC (RIHD) mentioned above to  
"On" on the unit, and make the following setting.  
HDMI CEC (RIHD)  
Press RCV on the remote controller and then press  
HOME.  
Select "Setup" with the cursor buttons and press  
ENTER.  
Select "11. HDMI Setup" with the cursor buttons and  
press ENTER.  
Select "Audio Return Ch" with the cursor buttons  
and select "Auto".  
1.  
2.  
3.  
4.  
d c  
/ buttons and change the volume  
Move the cursor with  
level of each speaker. A test tone will be output each time  
you change the level. Select the desired level. Press HOME  
to save the changed setting and close the menu screen.  
rꢀ In the following cases, the setting cannot be changed:  
– Headphones are connected.  
– Audio is output from the speakers of the TV.  
– Muting is enabled.  
Turning the TV to standby mode will turn the unit to  
standby mode.  
On the TV side, it is possible to set whether to output  
audio from the speakers connected to the unit or from  
the TV's speakers.  
Starting playback of a CEC compliant player/recorder will  
automatically switch the unit's input to the HDMI input of  
the player/recorder. If the unit is in standby mode, it will  
automatically be turned on.  
Audio output of connected players  
To enjoy digital surround sound including Dolby Digital  
and DTS, audio output should be set to "Bitstream  
output" on the connected blu-ray disc player or other  
devices. If the TV does not support bitstream signals,  
set the audio output to "PCM output" on the player to  
listen to the audio from the TV's speakers. For how  
to set the player, see the instruction manual of the  
player. Some settings of the blu-ray disc player may  
prevent reproduction of DTS-HD Master Audio. In  
that case, turn "BD video supplementary sound" (or  
secondary sound) to "Off" and try again.  
rꢀ You cannot change the volume level of speakers when  
"No" or "None" is set for them in "Sp Config".  
Press RCV on the remote controller and then press  
HOME.  
Select "Setup" with the cursor buttons and press  
ENTER.  
Select "11. HDMI Setup" with the cursor buttons and  
press ENTER.  
Select "HDMI CEC (RIHD)" with the cursor buttons  
and select "On".  
1.  
2.  
3.  
4.  
 
8
Playing Back  
Step 3:  
Remote controller parts name  
Playing the player and TV  
1
1
2
1
RECEIVER button: Turns the unit on or into standby  
z
mode.  
2 RCV button: Switches the remote controller to the  
mode for operating this unit.  
8
9
3
3 REMOTE MODE/INPUT SELECTOR buttons: Switches  
the input to be played.  
¼
The input selector button NET has no effect on this unit, since the unit  
does not have input selector “NET”.  
z To control the unit: The remote controller may be in the  
remote mode that enables control of other devices. In the  
state of remote mode, you will not be able to operate this  
unit. When you operate the unit, operate it from back to (a  
mode in which to operate this unit) RECEIVER mode by  
4 Cursor buttons and ENTER button: Moves the cursor  
and confirms the selection.  
5 Q SETUP button: Displays the Quick Setup menu that  
allows you to set the frequently used functions including  
input selection and volume adjustment.  
F
pressing  
RCV always.  
2
6 Listening mode buttons: Allows you to select the  
4
5
Turning the power on.  
1.  
listening mode.  
G
H
Press  
RECEIVER on the remote controller to turn  
1 z  
7 DIMMER button: Switches the brightness of the display.  
8 ZONE2 button: For use when the unit is connected with  
a pre-main amplifier in a separate room and sound is  
played there.  
the power on.  
rꢀ You need to change the input setting of the TV to the  
one for connection with this unit. Use the TV's remote  
controller.  
9 MUTING button: Temporarily mutes audio.  
VOLUME buttons: Allows you to adjust the volume.  
RETURN button: Returns the display to the previous  
state.  
HOME button: Displays the Home menu that allows you  
to make advanced settings and use other functions.  
DISPLAY button: Switches the information on the  
display.  
F
G
Select the input of the unit and start playback on the  
player or TV.  
2.  
6
7
rꢀ Press  
INPUT SELECTOR to which the desired  
3
H
I
player has been assigned. Press TV/CD to play the  
TV's sound.You can also use the input selector  
buttons on the main unit.  
rꢀ Input will automatically be selected if the TV or player  
is CEC compliant and connected to the unit with  
HDMI cable.  
-
1 I  
rꢀ The buttons other than  
devices.  
are for operating other  
I
Select the desired listening mode.  
3.  
4.  
Press the  
listening mode buttons to switch the  
6
mode so that you can enjoy different listening modes.  
For details about the listening modes, see "Listening  
modes".  
Adjust the volume with  
.
F
 
9
Step 3: Playing Back  
Adjusting Sound Quality: It is possible to enhance  
or moderate the bass and treble of front speakers. Press  
TONE on the main unit several times to select the desired  
setting from "Bass", "Treble", and "PM Bass" (Phase  
Matching Bass), and adjust with +/-.  
Listening modes  
Listening to AM/FM Radio  
2
Select the desired mode by switching and listening actual  
sound in different modes. The selectable listening modes  
depend on the format of the input signals.  
Auto tuning method is explained in Basic Manual. For more  
details on AM/FM radio station, see Advanced Manual.  
"Bass": Allows you to enhance or moderate the bass.  
"Treble": Allows you to enhance or moderate the treble.  
"PM Bass": Allows you to keep the clear midrange and  
effectively enhance the bass.  
Press AM or FM on the unit to select either "AM" or  
"FM".  
Press TUNING MODE on the unit so that the "AUTO"  
indicator on the unit's display lights.  
1.  
2.  
3.  
MOVIE/TV:You can select a listening mode suitable for  
movies and TV programs.  
MUSIC:You can select a listening mode suitable for music.  
Muting Temporarily: Press MUTING on the remote  
controller. Press MUTING again to cancel muting.  
GAME:You can select a listening mode suitable for games.  
Press TUNING on the unit.  
The automatic search for a radio station starts.  
Searching stops when one is found. When tuned into a  
radio station, the " TUNED " indicator on the unit's  
display lights. The "FM STEREO" indicator lights if the  
radio station is an FM radio station.  
STEREO:You can select a listening mode for stereo and all  
Changing the Display Brightness: Press DIMMER on  
the remote controller several times to select the desired  
brightness.  
channel stereo sources.  
rꢀ For details on the listening modes, see the Advanced  
Manual.  
Changing the Input Display: Press DISPLAY on the  
remote controller several times to switch the display of the  
main unit in order of:  
TUNED  
AUTO  
"Direct" for playing the input signals as-is  
Selecting this mode allows the input signals to be  
played as they are. For example, 2 ch signals of music  
CD will be played in stereo, 5.1 ch signals in 5.1 ch,  
and Dolby Digital signals of blu-ray disc or DVD in the  
Dolby Digital sound field according to the specified  
number of channels.  
Input source &  
volume  
FM STEREO  
(Actual display depends on the country.)  
Listening  
mode  
Registering a Radio Station: It allows you to register up to  
40 of your favorite AM/FM radio stations.  
1. Tune into the AM/FM radio station you want to register.  
2. Press MEMORY on the unit so that the preset number  
on the display flashes.  
3. Repeatedly press PRESET on the unit to select a  
number between 1 and 40 while the preset number is  
flashing (about 8 seconds).  
Other useful functions  
Signal  
format  
Playing Video and Audio from Different Sources: It  
is possible to play audio and video from different sources.  
For example, you can play audio from the CD player and  
video from the BD/DVD player. In this case, press BD/DVD  
and then TV/CD. Then start playback on the BD/DVD player  
and CD player. This function is effective when an input with  
audio only has been selected (TV/CD, AM or FM in the  
initial setting).  
Sampling  
frequency  
4. Press MEMORY on the unit again.  
When registered, the preset number stops flashing.  
Repeat this procedure for all of your favorite AM/FM  
radio stations. Press PRESET or CH +/- to select  
the registered radio station.  
rꢀ If "Dolby D 5.1" is displayed in signal format, the  
Dolby Digital 5.1 ch signals are being input. When  
listening to AM/FM radio, the band, frequency and  
preset number are displayed.  
 
10  
Step 3: Playing Back  
Sleep Timer: Select to turn the unit into standby mode  
Playing sound of the Bluetooth-enabled device  
Connecting and playing the Bluetooth-  
enabled device  
automatically when the specified time elapses.  
3
If the unit is on and the Bluetooth-enabled device is  
connected, the input will be automatically switched to  
"BLUETOOTH". Play music in this state.  
rꢀ It may take about a minute until connection is established  
when the unit is on since the Bluetooth function takes  
some time to start up.  
rꢀ If the volume setting on the Bluetooth-enabled device is  
low, the sound will not be output from this unit.  
rꢀ Due to the characteristics of Bluetooth wireless  
technology, the sound produced on this unit may slightly  
be behind the sound played on the Bluetooth-enabled  
device.  
InstaPrevue: Select to preview videos input from the  
HDMI input jacks collectively in a single screen. The screen  
has a main window (current input video) and sub windows  
(other input videos). To switch the current input, select the  
desired sub window with the cursor buttons and press  
ENTER.  
rꢀ A black sub window is shown for the input with no video  
signals.  
rꢀ "InstaPrevue" cannot be selected if the video is being  
input from HDMI IN 6 or there is no signal from the input  
currently selected.  
You can wirelessly enjoy music files stored in a smartphone  
or other Bluetooth-enabled device. The coverage area is  
ꢇꢊ|HGGVꢀꢅꢁꢋ|OGVGTUꢉꢃ  
rꢀ Depending on video signals, the picture may not be  
properly rendered on the preview thumbnails.  
rꢀ The Bluetooth-enabled device needs to support the  
A2DP profile.  
rꢀ Note that connection is not always guaranteed with all  
Bluetooth-enabled devices.  
Using the Home menu  
4
In the Home menu, you can make advanced settings and  
use functions such as playback of files in USB storage  
device. For details on the operation, see the Advanced  
Manual.  
Pairing  
Pairing is necessary when using the Bluetooth-enabled  
device for the first time. Before starting the procedure, learn  
how to enable the Bluetooth setting function and to connect  
with other devices on the Bluetooth-enabled device.  
Press RCV on the remote controller and then press  
HOME.  
The Home menu displays on the TV screen.You can  
also use the HOME button on the main unit.  
1.  
Press BLUETOOTH on the remote controller.  
The unit enters the pairing mode and the BLUETOOTH  
indicator starts flashing.  
1.  
Home  
While the BLUETOOTH indicator is flashing,  
complete connection on the Bluetooth-enabled  
device in the nearby area within about 2 minutes.  
If the name of this unit is displayed on the Bluetooth-  
enabled device's display, select this unit. Paring will end  
after a short time.  
2.  
Setup  
USB  
Sleep Timer  
InstaPrevue  
rꢀ If a password is requested, enter "0000".  
rꢀ When connecting the unit to any other Bluetooth-  
enabled device, start pairing by pressing and holding  
BLUETOOTH until the BLUETOOTH indicator starts  
flashing. This unit can store the data of up to ten  
paired devices.  
Select the item with the cursor buttons of the  
remote controller and press ENTER to confirm your  
selection.  
To return to the previous screen, press RETURN. To  
return to the Home menu, press HOME.  
2.  
Setup:You can change the assignment of input terminals  
and input selector buttons and also make various speaker  
settings and other advanced settings.  
USB: Select to connect a USB storage device to the USB  
port so that it can be played.  
rꢀ "USB" becomes selectable after the USB function starts  
up even if it cannot be selected first. It may take about a  
minute to start up.  
 
11  
Step 3: Playing Back  
Late Night: Make small sounds to be easily heard. It  
is useful when you need to reduce the volume while  
watching a movie late night.You can enjoy the effect  
on Dolby Digital, Dolby Digital Plus and Dolby TrueHD  
sources only.  
rꢀ Turning the unit to standby mode will set the setting  
to "Off". In case of Dolby TrueHD, the setting will be  
set to "Auto".  
Using Quick Setup menu  
5
In the Quick Setup menu, you can set frequently used  
functions including input selection and volume adjustment.  
Press Q SETUP on the remote controller.  
The Quick Setup menu is displayed on the connected  
TV's screen.  
1.  
Music Optimizer : Improve the quality of the  
compressed audio. Playback sound of lossy  
compressed files such as MP3 will be improved. The  
setting can be separately set to each input.  
rꢀ The setting is effective in the signals of 48 kHz or  
less. The setting is not effective in the bitstream  
signals.  
Quick Setup  
Input  
Audio  
Information  
Listening Mode  
rꢀ It cannot be set if the listening mode is Direct.  
Cinema Filter: Adjust the soundtrack that was  
processed to enhance its high pitch range, in order to  
make it suitable for home theater.  
rꢀ This function can be used in the following listening  
modes: Multichannel, Dolby Digital, Dolby Digital  
Plus, Dolby TrueHD, DTS, DTS-HD High Resolution  
Audio, DTS-HD Master Audio, DTS Express, DTS  
96/24, Dolby PL II Movie, DTS Neo:6 and Neo:6  
Cinema.  
Select the item with the cursor buttons of the  
remote controller and press ENTER to confirm your  
selection.  
2.  
To return to the previous screen, press RETURN.  
Input: Select the input and check the assignment of input  
selector buttons.  
Audio:You can change various audio settings including  
the ones for adjusting audio quality and speaker level.  
rꢀ You cannot select this item when audio is played from the  
TV's speakers.  
Information: Display the audio information.  
Listening Mode: Select the listening mode from the  
categories of "MOVIE/TV", "MUSIC" and "GAME".  
rꢀ It cannot be set when audio is played from the TV's  
speakers.  
A/V Sync: If the video is behind the audio, you can  
delay the audio to offset the gap.  
rꢀ It cannot be set if the input is "USB" or  
"BLUETOOTH".  
rꢀ It cannot be set if the listening mode is Direct.  
Bass,Treble: Adjust volume of the front speaker.  
rꢀ It cannot be set if the listening mode is Direct.  
PM Bass (Phase Matching Bass): Suppress phase  
shift in the midrange to enhance bass sound. Thus  
smooth and powerful bass sound can be obtained.  
rꢀ It cannot be set if the listening mode is Direct.  
Subwoofer Level, Center Level: Adjust the speaker  
level while listening to the sound. The adjustment you  
made will be reset to the previous status when you turn  
the unit to standby mode.  
rꢀ The speakers cannot be adjusted if they have been  
set to "No" or "None" in "Sp Config".  
 
12  
Step 3: Playing Back  
Making multi-zone connection  
Performing multi-zone playback  
Using the multi-zone function  
6
Press ZONE2 on the remote controller, point the  
remote controller at the remote controller sensor  
Connect the ZONE 2 LINE OUT jacks of the unit and the  
line-in jacks of the pre-main amplifier in a separate room  
with an analog audio (RCA) cable.  
1.  
You can listen to the sound in a separate room by making  
the Zone connection (analog) between the unit and an  
integrated amplifier placed in the separate room.  
You can use a Blu-ray Disc player in the main room in  
which the unit is placed, while receiving AM/FM broadcast  
in the separate room. Audio can be played in the main  
room and the separate room simultaneously, or only in the  
separate room.  
and press RECEIVER.  
z
"Z2" lights on the unit and the ZONE function is enabled.  
(ZONE 2 is now on.)  
Press ZONE2 on the remote controller again and  
press INPUT SELECTOR of the input to be played in  
a separate room.  
2.  
To play the same source in the main room and separate  
room, hold down ZONE2 for approximately 3 seconds.  
The volume should be adjusted with the pre-main  
amplifier used in the separate room.  
rꢀ The sources you can enjoy in the separate room are the  
players connected to the analog audio input jacks of the  
unit, and AM/FM broadcast.  
rꢀ When listening to AM/FM broadcasting, you cannot  
select different stations for the main room and separate  
room. Therefore broadcasting of the same station will be  
heard in the both rooms.  
To control on the main unit: Press ZONE2 and within  
ꢊ|UGEQPFUꢌꢀRTGUUꢀVJGꢀKPRWVꢀUGNGEVQTꢀDWVVQPꢀQHꢀVJGꢀKPRWVꢀVQꢀDGꢀ  
played in a separate room. To play the same source in the  
main room and separate room, press ZONE2 twice.  
To turn off the multi-zone function: Press ZONE2 on the  
Connecting with Player  
remote controller and press RECEIVER. Alternatively  
z
press OFF on the main unit.  
To use a Blu-ray Disc player or other players as the source  
of Zone audio output, it is necessary to connect the RCA  
audio output jacks of the player and the analog audio input  
jacks of the unit using the analog audio (RCA) cable.  
rꢀ Multi-zone playback cannot be performed if a player is  
connected to HDMI jack using HDMI cable or OPTICAL/  
COAXIAL jack using digital cable. Connect the players  
using analog audio cable for multi-zone playback. Analog  
audio output setting may be necessary on the player.  
rꢀ If ZONE 2 is on, power consumption during standby  
becomes larger than normal.  
AUDIO  
OUT  
rꢀ While ZONE 2 is on, the RI linked system function  
(interlink between Onkyo components) is disabled.  
rꢀ Zone audio output is not possible if the player and the unit  
are connected only via HDMI cable or digital cable.  
rꢀ Some players require analog audio output setting.  
 
13  
1
2
3
4 5  
6
7
8
9
F
G
H
I
J
K
(European and Asian  
models)  
M
N
O
Q
R
L
P
Front Panel  
TUNING MODE button: Switches the tuning mode.  
Input selector buttons: Switches the input to be  
played.  
DISPLAY button: Switches the information on the  
display.  
AUX INPUT AUDIO/VIDEO jacks: A video camera or  
such other device is connected.  
HDMI THRU indicator: Lights when HDMI Through  
function is enabled.  
1
2
ON/STANDBY button: Turns the unit on or into  
F
G
H
I
O
P
Q
R
z
QUICK SETUP button: Displays the Quick Setup menu.  
standby mode.  
HOME button: Displays the Home menu.  
BLUETOOTH indicator: Flashes while pairing with a  
Bluetooth-enabled device is in progress and stays lit  
when pairing is completed.  
ZONE 2 button: Controls the ZONE function.  
OFF button: Switches the ZONE function to off.  
Remote control sensor: Receives signals from the  
remote controller.  
d
c
Cursor buttons, lTUNINGj button, PRESET  
button and ENTER button: Moves the cursor and  
confirms the selection. When listening to AM/FM  
broadcasting, tune in to the station with lTUNINGj or  
3
4
5
d
c
.
select the registered station with PRESET  
RETURN button: Returns the display to the previous  
state.  
MASTER VOLUME: Allows you to adjust the volume.  
MUSIC OPTIMIZER button and indicator: Turns on/  
off the MUSIC OPTIMIZER function that improves the  
quality of the compressed audio.  
J
Display  
6
7
LISTENING MODE buttons: Allows you to select the  
listening mode.  
K
L
8 DIMMER button (North American model): Switches  
the brightness of the display.  
PHONES jack: Stereo headphones with a standard plug  
are connected.  
TONE and Tone Level buttons: Adjusts the high tone  
and low tone.  
RT/PTY/TP button (European, and Asian models):  
Can be used when receiving the station transmitting text  
information.  
M
N
MEMORY button: Registers or deletes a station.  
9
 
14  
1
2
3
4
5
6
7
1 23  
4
9
5
6
7
8
Display  
Lights in the following conditions. "Z2": ZONE 2 output  
is on. / "HDMI": HDMI signals are input and HDMI input  
selector is selected. / "ARC": Audio signals are input  
from ARC compatible TV and TV/CD input selector  
is selected. / "3D": Input signals are 3D. / "USB" (¼):  
"USB" input is selected and USB storage device is  
connected. / "DIGITAL": Digital signals are input and  
the digital input selector is selected. / Cursor indicators:  
USB is controlled.  
1
8
9
F
G
¼
"USB" will flash if the connection is not correct.  
Lights when headphones are connected.  
Lights when USB is controlled.  
Lights according to the type of input digital signals and  
the listening mode.  
2
3
4
Rear Panel  
RI REMOTE CONTROL jack: An Onkyo product with RI  
jack can be connected and synchronized with this unit.  
(/ꢀ#06'00#ꢀLCEMꢀꢁꢂꢃꢀŝꢄꢀCPFꢀ#/ꢀ#06'00#ꢀ  
terminal: The supplied antennas are connected.  
USB port: A USB storage device is connected so that  
music files stored in it can be played.  
COMPONENT VIDEO IN and OUT jacks: Component  
video input/output jacks  
HDMI IN/OUT jacks: Digital video signals and audio  
signals are transmitted between the unit and the  
connected devices.  
DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio  
signals are input.  
Composite VIDEO/AUDIO IN jacks: Analog video  
signals and audio signals are input.  
Composite MONITOR OUT V jack: Video signals are  
output to the connected monitor or TV.  
LINE OUT ZONE 2 jacks: Audio output jacks connected  
to the pre-main amplifier for multi-zone playback in a  
separate room.  
1
2
3
4
5
8
9
F
G
Lights when Music Optimizer is enabled.  
5
6
Lights in the following conditions. "AUTO": Tuning mode  
is auto. / "fTUNEDe": Receiving AM/FM radio. fe  
flashes while tuning is automatically performed. / "FM  
STEREO": Receiving FM stereo. / "RDS" (European and  
Asian models): Receiving RDS broadcasting.  
"MUTING": Flashes when muting is on.  
Lights in the following conditions. "SLEEP": Sleep timer  
has been set. / "ASb" (Auto Standby): Auto Standby  
is on. / "ch": Channel is being set. / "Hz": Crossover  
frequencies are being set. / "m ft": Speaker distances  
are being set. / "dB": Speaker volume is being set.  
Displays various information of the input signals.  
Pressing DISPLAY displays the type of input digital  
signals and the listening mode.  
7
8
SPEAKERS terminals: Speakers are connected.  
Power cord  
6
7
9
 
15  
Troubleshooting  
The remote controller does not work.  
rꢀ Be sure to press RCV first before operating the unit with  
the remote controller.  
Resetting the unit  
Before starting the procedure  
Problems may be solved by simply turning the power  
on/off or disconnecting/connecting the power cord,  
which is easier than working on the connection, setting  
and operating procedure. Try the simple measures  
on both the unit and the connected device. If the  
problem is that the video or audio is not output or the  
HDMI linked operation does not work, disconnecting/  
connecting the HDMI cable may solve it. When  
reconnecting, be careful not to wind the HDMI cable  
since if wound the HDMI cable may not fit well.  
After reconnecting, turn off and on the unit and the  
connected device.  
Resetting the unit to the status at the time of shipment may  
solve the problem. If the measures above do not solve the  
problem, reset the unit with the following procedure. If you  
reset the unit status, your preferences will be reset to the  
defaults. Note them down before starting reset.  
There is no sound when multi-zone function is  
used.  
rꢀ With multi-zone function, sound is output only when an  
external component connected to the analog audio input  
jacks of the unit is used, or when AM/FM broadcast is  
received. Multi-zone audio output is not possible if the  
player and the unit are connected via HDMI cable or  
digital cable. Connect the RCA audio output jacks of the  
player and the analog audio input jacks of the unit with  
an analog audio (RCA) cable. Also, some players require  
analog audio output setting.  
z How to reset:  
While holding down CBL/SAT on the main unit (note  
that step 2 must be performed with this button  
pressed down)  
1.  
2.  
Press ON/STANDBY on the main unit ("Clear"  
z
appears on the display and the unit returns to standby)  
C l e a r  
The AV receiver turns off unexpectedly.  
rꢀ The AV receiver will automatically enter standby mode  
when Auto Standby is set and launched.  
Bluetooth  
rꢀ Try plugging/unplugging the unit and the Bluetooth-  
enabled player. After that, check that the Bluetooth  
function is enabled on the Bluetooth-enabled device and  
the connection with the unit has been established.  
There’s no sound, or it’s very quiet.  
rꢀ A wrong input selector button has been selected. Select  
a correct input for the player. Also check that muting is  
not on.  
Press ON/STANDBY.  
While holding down  
1.  
CBL/SAT,  
2.  
z
rꢀ Not all listening modes use all speakers.  
z How to reset the remote controller:  
While holding down RCV on the remote controller,  
press HOME until the remote indicator stays lit  
(about 3 seconds)  
1.  
There’s no picture.  
rꢀ A wrong input selector button has been selected.  
rꢀ To display video from the connected player on the TV  
screen while the unit is in standby, you need to enable  
"HDMI Through".  
Within 30 seconds, press RCV again  
2.  
Remote  
indicator  
RCV  
rꢀ When the TV image is blurry or unclear, power code or  
connection cables of the unit may have interfered. In  
that case, keep distance between TV antenna cable and  
cables of the unit.  
HDMI control does not function correctly.  
rꢀ Set the HDMI CEC (RIHD) setting of the unit to "On". It is  
also necessary to make the HDMI linked system setting  
on the TV. See the TV's instruction manual for details.  
HOME  
 
16  
Specifications  
HDMI  
Amplifier Section  
Tuner Section  
Input  
Rated Output Power  
FM Tuning Frequency Range  
87.5 MHz - 107.9 MHz (North American)  
87.5 MHz - 108.0 MHz, RDS (Others)  
AM Tuning Frequency Range  
522/530 kHz - 1611/1710 kHz  
Preset Channel  
IN1 (BD/DVD), IN2 (CBL/SAT), IN3 (STB/DVR), IN4 (GAME), IN5 (PC),  
IN6  
Output  
OUT  
Video Resolution  
Pass Through : 4K 60 Hz (YCbCr 4:2:0)  
Audio Format  
DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,  
Dolby Digital Plus, DSD, Multichannel PCM  
Supported  
All channels: 65 watts minimum continuous power per channel,  
ꢅ|QJOꢀNQCFUꢆꢀꢇꢀEJCPPGNUꢀFTKXGPꢀHTQOꢀꢇꢈꢀ*\ꢀVQꢀꢇꢈꢀM*\ꢆꢀYKVJꢀCꢀ  
maximum total harmonic distortion of 0.7% (FTC)  
90 watts minimum continuous power per channel, 6 ohm loads,  
ꢇ|EJCPPGNUꢀFTKXGPꢀCVꢀꢉꢀM*\ꢆꢀYKVJꢀCꢀOCZKOWOꢀVQVCNꢀJCTOQPKEꢀ  
distortion of 0.7% (FTC)  
110 watts minimum continuous power per channel, 6 ohm loads,  
ꢉ|EJCPPGNꢀFTKXGPꢀCVꢀꢉꢀM*\ꢆꢀYKVJꢀCꢀOCZKOWOꢀVQVCNꢀJCTOQPKEꢀFKUVQTVKQPꢀ  
of 1 %  
40  
Bluetooth Section  
Communication system  
(North American)  
6 ch × 100 W at 6 ohms, 1 kHz, 1 ch driven of 1% (IEC) (Others)  
3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD)  
Bluetooth Specification version 2.1 + EDR (Enhanced Data Rate)  
Maximum communication range  
Line of sight approx. 15 m (  
Frequency band  
2.4 GHz band (2.4000 GHz - 2.4835 GHz)  
Modulation method  
FHSS (Freq Hopping Spread Spectrum)  
Compatible Bluetooth profiles  
A2DP 1.2 (Advanced Audio Distribution Profile)  
AVRCP 1.3 (Audio Video Remote Control Profile)  
Supported Codecs  
Maximum Effective Output Power  
Video Inputs  
Component  
IN (GAME)  
Composite  
¼
)
6 ch × 120 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) (Asian)  
¼
Dynamic Power (  
)
IEC60268-Short-term maximum output power  
¼ꢀ  
ꢁꢂꢍꢀ9ꢀꢅꢈꢀŝꢌꢀ(TQPVꢉ  
ꢁꢎꢋꢀ9ꢀꢅꢇꢀŝꢌꢀ(TQPVꢉ  
ꢊꢋꢀ9ꢀꢅꢊꢀŝꢌꢀ(TQPVꢉ  
IN1 (CBL/SAT), IN2 (STB/DVR), IN3 (GAME), AUX  
Video Outputs  
Component  
OUT  
Composite  
THD+N (Total Harmonic Distortion+Noise)  
0.7% (20 Hz - 20 kHz, half power)  
Damping Factor  
SBC  
ꢂꢍꢀꢅ(TQPVꢌꢀꢁꢀM*\ꢌꢀꢊꢀŝꢉ  
Input Sensitivity and Impedance (Unbalance)  
ꢎꢍꢍꢀO8ꢆꢇꢏꢀMŝꢀꢅ.+0'ꢉ  
Rated RCA Output Level and Impedance  
ꢁꢍꢍꢀO8ꢆꢎꢃꢎꢀMŝꢀꢅ.+0'ꢀ176ꢉ  
Maximum RCA Output Level and Impedance  
ꢁꢃꢍꢀ8ꢆꢎꢃꢎꢀMŝꢀꢅ.+0'ꢀ176ꢉ  
Transmission range (A2DP)  
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)  
¼ꢀ  
The actual range will vary depending on factors such as obstacles  
MONITOR OUT  
Audio Inputs  
Digital  
OPTICAL (TV/CD)  
COAXIAL 1 (BD/DVD), 2 (CBL/SAT)  
Analog  
between devices, magnetic fields around a microwave oven, static  
electricity, cordless phone, reception sensitivity, antenna’s  
performance, operating system, software application, etc.  
Frequency Response  
BD/DVD, CBL/SAT, STB/DVR, GAME, PC, TV/CD, AUX  
5 Hz - 100 kHz/+1 dB, –3 dB (Direct mode)  
Tone Control Characteristics  
10 dB, 20 Hz (BASS)  
10 dB, 20 kHz (TREBLE)  
Signal to Noise Ratio  
General  
Power Supply  
AC 120 V, 60 Hz (North American)  
AC 230 V, 50 Hz (European, Australian and British)  
AC 220 - 240 V, 50/60 Hz (Others)  
Power Consumption  
Audio Outputs  
Analog  
ZONE2 LINE OUT  
Speaker Outputs  
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER  
Phones  
100 dB (LINE, IHF-A)  
Speaker Impedance  
3.8 A (North American)  
380 W (European, Australian and British)  
410 W (Others)  
0.2 W (Stand-by, North American)  
0.3 W (Stand-by, Others)  
55 W (No-sound)  
ꢂꢀŝꢀꢐꢀꢁꢂꢀŝ  
PHONES (Front, ø 6.3)  
Others  
RI  
USB  
Video Section  
Input Sensitivity/Output Level and Impedance  
1
1
ꢁꢀ8RꢐRꢆꢏꢋꢀŝꢀꢅ%QORQPGPVꢀ;ꢉ  
Dimensions (W × H × D)  
435 mm × 150 mm × 321 mm  
17-1/8" × 5-7/8" × 12-5/8"  
Weight  
ꢍꢃꢏꢀ8RꢐRꢆꢏꢋꢀŝꢀꢅ%QORQPGPVꢀ2B/CB, PR/CR)  
ꢁꢀ8RꢐRꢆꢏꢋꢀŝꢀꢅ%QORQUKVGꢉ  
Component Video Frequency Response  
5 Hz - 100 MHz/+0 dB, –3 dB  
Specifications and features are subject to change without notice.  
7.6 kg (16.8 lbs.) (North American)  
8.1 kg (17.9 lbs.) (Others)  
 
17  
License and Trademark Information  
QR Code is a registered trademark of DENSO WAVE INCORPORATED.  
Safari is a trademark or registered trademark of Apple Computer, Inc. in the  
United States and other countries.  
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the  
double-D symbol are trademarks of Dolby Laboratories.  
“x.v.Color” is a trademark of Sony Corporation.  
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and  
Thomson.  
Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the  
Symbol, & DTS and the Symbol together are registered trademarks of DTS,  
“All other trademarks are the property of their respective owners.”  
©
Inc. DTS, Inc. All Rights Reserved.  
"CINEMA FILTER" and "CINEMA FILTER (logo)" are trademarks of Onkyo  
Corporation.  
AccuEQ, Music Optimizer, RIHD and WRAT are trademarks of Onkyo  
Corporation.  
"RIHD" and "RIHD (logo)" are trademarks of Onkyo Corporation.  
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI  
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the  
United States and other countries.  
The Bluetooth® word mark and logos are registered trademarks owned by  
Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license.  
Other trademarks and trade names are those of their respective owners.  
Onkyo does not guarantee Bluetooth compatibility between the AV receiver and  
all Bluetooth-enabled devices.  
For compatibility between the AV receiver and another device with Bluetooth  
technology, consult the device’s documentation and dealer. In some countries,  
there may be restrictions on using Bluetooth devices. Check with your local  
authorities.  
InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks  
of Silicon Image, Inc. in the United States and other countries.  
Apple, iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and  
other countries.  
Apple TV is a trademark of Apple Inc., registered in the U.S. and other  
countries.  
This product is protected by certain intellectual property rights of Microsoft. Use  
or distribution of such technology outside of this product is prohibited without a  
license from Microsoft.  
Windows and the Windows logo are trademarks of the Microsoft group of  
companies.  
 
18  
2TKPꢀRTG\GPVCꢌꢀ1PM[Qꢀ%QTRQTCVKQPꢌꢀFGENCTàꢀEàꢀCRCTCVWNꢀ*64ꢈꢑꢈꢀGUVGꢀ  
ÊPꢀEQPHQTOKVCVGꢀEWꢀEGTKPķGNGꢀGUGPķKCNGꢀĵKꢀEWꢀCNVGꢀRTGXGFGTKꢀRGTVKPGPVGꢀCNGꢀ  
Directivei 1999/5/CE.  
Precautions  
For European Models  
Declaration of Conformity  
We declare, under our sole responsibility, that this  
product complies with the standards:  
1PM[Qꢀ%QTRQTCVKQPꢀVÙOVQꢀX[JNCUWLGꢌꢀzGꢀ*64ꢈꢑꢈꢀCꢀURĔĢCꢀ\½MNCFPÅꢀ  
RQzKCFCXM[ꢀCꢀXwGVM[ꢀRTÉUNWwPÅꢀWUVCPQXGPKCꢀ5OGTPKEGꢀꢁꢑꢑꢑꢆꢋꢆ'5ꢃ  
Onkyo Corporation izjavlja, da je ta HT-R393 v skladu z bistvenimi  
\CJVGXCOKꢀKPꢀFTWIKOKꢀTGNGXCPVPKOKꢀFQNQêKNKꢀFKTGMVKXGꢀꢁꢑꢑꢑꢆꢋꢆ'5ꢃ  
Onkyo Corporation vakuuttaa täten että HT-R393 tyyppinen laite on  
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin  
muiden ehtojen mukainen.  
Safety  
Limits and methods of measurement of radio  
*ÀTOGFꢀHÒTMNCTCTꢀ1PM[Qꢀ%QTRQTCVKQPꢀCVVꢀFGPPCꢀ*64ꢈꢑꢈꢀHÒNLGTꢀFGꢀXÀUGPVNKICꢀ  
kraven och andra relevanta stadgar i Direktiv 1999/5/EC.  
Hér með lýsir Onkyo Corporation því yfir að varan HT-R393 er í samræmi  
XKÌꢀITWPPMTÒHWTꢀQIꢀCÌTCTꢀMTÒHWTꢀUGOꢀIGTÌCTꢀGTWꢀÉꢀVKNUMKRWPꢀꢁꢑꢑꢑꢆꢋꢆ'%ꢃ  
Onkyo Corporation erklærer herved at denne HT-R393 er i  
overensstemmelse med vesentlige krav og andre relevante bestemmelser i  
direktiv 1999/5/EC.  
disturbance characteristics  
Limits for harmonic current emissions  
Limitation of voltage changes, voltage fluctuations and flicker  
RoHS Directive, 2011/65/EU  
Hereby, Onkyo Corporation, declares that this HT-R393 is in compliance  
with the essential requirements and other relevant provisions of Directive  
1999/5/EC.  
µꢀÑÄÕÖÒãÝÉÖÒꢁꢀ2QN\Rꢀ&RUSRUDWLRQꢁꢀÈÉÎÏÄÔÌÔÄꢁꢀÛÉꢀ+75ꢃꢄꢃꢀÉꢀÆꢀ  
ÕÞÒÖÆÉÖÕÖÆÌÉꢀÕÞÕꢀÕÞÝÉÕÖÆÉÑÌÖÉꢀÌËÌÕÎÆÄÑÌãꢀÌꢀÈÔ×ÇÌÖÉÓÔÌÏÒÊÌÐÌꢀ  
ÔÄËÓÒÔÉÈÅÌꢀÑÄꢀ¨ÌÔÉÎÖÌÆÄꢀꢅꢄꢄꢄꢆꢇꢆ(&ꢈ  
1XKOGꢀ1PM[Qꢀ%QTRQTCVKQPꢌꢀRQVXTîWLGꢀFCꢀLGꢀ*64ꢈꢑꢈꢀWꢀUWINCUPQUVKꢀUCꢀ  
osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999/5/EC.  
1PM[Qꢀ%QTRQTCVKQPꢀVÉOVQꢀRTQJNCwWLGꢌꢀzGꢀ*64ꢈꢑꢈꢀURNĢWLGꢀ\½MNCFPÉꢀ  
RQzCFCXM[ꢀCꢀXwGEJPCꢀRįÉUNWwP½ꢀWUVCPQXGPKꢀ5OøTPKEGꢀꢁꢑꢑꢑꢆꢋꢆ'5ꢃ  
Undertegnede Onkyo Corporation erklærer herved, at følgende udstyr  
HT-R393 overholder de væsentlige krav og øvrige relevante krav i direktiv  
1999/5/EF.  
Hiermit erklärt Onkyo Corporation, dass sich das Gerät HT-R393 in  
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen  
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.  
Käesolevaga kinnitab Onkyo Corporation seadme HT-R393 vastavust  
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele  
teistele asjakohastele sätetele.  
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo Corporation ΔΗΛΩΝΕΙ  
ΟΤΙ HT-R393 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ  
ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ  
Por la presente, Onkyo Corporation, declara que este HT-R393 cumple  
con los requisitos esenciales y otras exigencias relevantes de la Directiva  
1999/5/EC.  
Par la présente, Onkyo Corporation déclare que l’appareil HT-R393 est  
conforme aux exigences essentielles et aux autres dispositions pertinentes  
de la directive 1999/5/CE.  
Con la presente Onkyo Corporation dichiara che questo HT-R393 è  
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite  
dalla direttiva 1999/5/CE.  
#TꢀwQꢀ1PM[Qꢀ%QTRQTCVKQPꢀFGMNCTðꢌꢀMCꢀ*64ꢈꢑꢈꢀCVDKNUVꢀ&KTGMVĈXCUꢀꢁꢑꢑꢑꢆꢋꢆ'-ꢀ  
DĿVKUMCLÞOꢀRTCUĈDÞOꢀWPꢀEKVKGOꢀCTꢀVQꢀUCKUVĈVCLKGOꢀPQVGKMWOKGOꢃ  
Šiuo Onkyo Corporation deklaruoja, kad šis HT-R393 atitinka esminius  
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.  
A Onkyo Corporation ezzennel kijelenti, hogy a HT-R393 típusú beren-  
FG\ÅUꢀVGNLGUÉVKꢀC\ꢀCNCRXGVĩꢀMÒXGVGNOÅP[GMGVꢀÅUꢀO½Uꢀꢁꢑꢑꢑꢆꢋꢆ'-ꢀKT½P[GNXDGPꢀ  
OGIJCV½TQ\QVVꢀXQPCVMQ\ÏꢀTGPFGNMG\ÅUGMGVꢃ  
Hierbij verklaart Onkyo Corporation dat het toestel l HT-R393 in  
overeenstemming is met de essentiële eisen en de andere relevante  
bepalingen van richtlijn 1999/5/EG.  
0KPKGLU\[Oꢀ1PM[Qꢀ%QTRQTCVKQPꢀFGMNCTWLGꢀŏGꢀ*64ꢈꢑꢈꢀLGUVꢀ\IQFP[ꢀ\ꢀ  
\CUCFPKE\[OKꢀY[OCICPKCOKꢀKꢀKPP[OKꢀYĜCıEKY[OKꢀRQUVCPQYKGPKCOKꢀ  
Dyrektywy 1999/5/EC.  
Eu, Onkyo Corporation, declaro que o HT-R393 cumpre os requisitos  
essenciais e outras provisões relevantes da Directiva 1999/5/EC.  
 
19  
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku, OSAKA 541-0041, JAPAN  
The Americas  
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.  
For Dealer, Service, Order and all other Business Inquiries:  
Tel: 201-785-2600 Fax: 201-785-2650  
For Product Support Team Only:  
1-800-229-1687  
Europe  
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY  
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213  
Meridien House, Ground floor, 69 - 71 Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom  
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95  
China  
(Hong Kong)  
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.  
Tel: 852-2429-3118 Fax: 852-2428-9039  
(Mainland)  
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,  
Tel: 86-21-52131366 Fax: 86-21-52130396  
Asia, Oceania, Middle East, Africa  
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.  
The above-mentioned information is subject to change without prior notice.  
Visit the Onkyo web site for the latest update.  
D1405-0  
SN 29401799  
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.  
* 2 9 4 0 1 7 9 9 *  
 

Miele Ventilation Hood DA 6290 D User Manual
Miele Washer M Nr 06 761 400 User Manual
Mustang Survival Life Jacket MD3183 User Manual
Mustek Printer PP3000 User Manual
NeoDigitscom DVD Player X3000 HD User Manual
Nextar Digital Photo Frame N7 105 User Manual
Onkyo DVD Player DV SP302 User Manual
Ovideon Computer Monitor RS232C User Manual
Panasonic Car Stereo System CQ 5251JU User Manual
Panasonic DVD Player DMP BD35 User Manual