One for All Universal Remote UR4 DSR User Manual

The device LED will blink number of times  
indicating the number of each digit of the  
code number. Each digit is separated by a 1  
second interval of the LED being turned off.  
B. Auto Search Method.  
STEP4 Press the [CH] button to save  
the power commands you stored.  
The [STB] button will blink twice  
to confirm the saving.  
Introduction  
Button Functions  
Programming the Remote Control  
1
3
5
Operating Instructions  
For 4 in 1  
STB Remote Control  
If the three-digit code numbers assigned to  
your brand do not turn off your equipment or  
the code tables do not list your brand, you  
can use the Auto Search Method to find the  
correct three-digit code number for your  
equipment by the following steps:  
The remote control is designed to  
operate the Motorola DSR400 Series  
Digital Receiver. You can also control  
the majority of TV, VCR/DVD and AUDIO  
equipment on the market as shown  
below.  
A. Three-Digit Code Programming  
Method.  
Example : One blink, three blinks and eight  
blinks with an interval of 1  
second of LED being turned off,  
indicates the code number 138.  
The remote control can be programmed by  
pressing in a three digit code number that  
corresponds to particular manufacturers and  
brands of Audio/Video equipment.  
The three-digit code numbers are listed in  
the code table of the instruction manual.  
F. Programming Channel Control.  
By following the steps below, the user can  
program the channel controls (Channel Up,  
Channel Down and Last) from one device  
to operate in another device mode. The  
default channel control settings on the  
remote control is as follows:  
STEP1 Turn on the equipment you wish to  
UR4-DSR  
STB : Digital Receiver  
: Televisions  
VCR : VCRs and DVD  
*Note : Ten blinks is equal to the number 0.  
operate.  
TV  
STEP2 Press the [DEVICE] button (TV, VCR  
or AUX) to be programmed and the  
[ENTER] button simultaneously for 3  
seconds. The device LED will turn on.  
STEP1 Turn on the equipment you wish to  
D. Programming a second TV to AUX Mode.  
program. (TV, VCR, DVD or AUX).  
AUX : Audio Receivers, DMX & DCR,  
STB : STB  
T V : STB  
STEP1 Press the [AUX] button to be  
programmed and the [ENTER]  
button simultaneously for 3 seconds.  
STEP2 Press the [DEVICE] button (TV, VCR  
or AUX) to be programmed and the  
[ENTER] button simultaneously for 3  
seconds. The device LED will turn  
on indicating the unit is ready to be  
programmed.  
TIVO, etc.  
VCR : VCR  
AUX : AUX  
*Tip : The device LED will light on for 20  
seconds. The next step must be  
entered while LED is on.  
If you wish to store the TV channel control  
in TV mode, use the following steps.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
Replacing Batteries  
2
STEP1 Press the [TV] button and the  
[ENTER] button simultaneously for  
3 seconds.  
Before you program or operate the  
remote control, you must install two  
new AAA alkaline batteries.  
STEP3 Press the [CH] or [CH] button  
one step at a time or keep it  
pressed. The remote will emit a  
series of Power ON/OFF commands.  
Release the [CH] or [CH] button  
as soon as the equipment turns off.  
STEP2 Press the [TV] button to pick up the  
*Tip : The device LED will stay lit for 20  
seconds. The next step must be  
entered while the LED is on.  
*Tip :The device LED will light on for 20  
seconds. The next step must be  
entered while the LED is on.  
TV code table.  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your TV  
brand from the code tables.  
STEP4 Store the three-digit code number  
by pressing the [AUX] button once  
again. The device LED will blink  
twice to confirm that the code has  
been stored.  
STEP1 Remove the battery compartment  
cover on the back of your remote  
control.  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your  
brand from the code tables.  
STEP2 Press the [VOL ] button.  
STEP3 Press the [TV] button.  
The device LED will blink twice to  
confirm the programming.  
*Tip : You can verify that you selected the  
correct code by pressing the  
[POWER] button. The equipment  
should either turn on or off.  
STEP2 Check battery polarity carefully,  
and install the batteries as  
shown in the illustration below.  
*Tip : The equipment will turn off when the  
correct three-digit code number has  
been entered. You can verify you have  
selected the correct code by pressing  
the [POWER] button, the equipment  
should turn on or turn off.  
To return to original state:  
STEP3 Replace the battery compartment  
If you wish to restore the STB channel  
cover.  
control in TV mode, repeat the above steps  
STEP4 Press the same [DEVICE] button to  
store the code. The Device LED will  
blink twice to confirm that the code  
has been stored.  
by pressing [STB] in STEP3  
.
E. Programming The System On/Off Button.  
This is designed to program the System On/Off  
button so that it can send out up to four power  
on/off commands with one button press.  
Operations  
G. Programming Volume Control .  
4
*Note : If there is more than one three-digit  
number listed for your brand, try one  
code number at a time until your  
equipment turns off.  
By following the steps below, the user can  
program the volume controls (Volume Up,  
Volume Down and Mute) from one device  
to operate in another device mode.  
The default volume control settings on the  
remote control is as follows :  
Default State :  
Device Default: Motorola DSR400 Series  
C. To Find the Three Digit Code  
Number That was Stored in the  
Device.  
.
STEP1 Press the [STB] button.  
Channel Default: STB channel and number keys through the STB, with the option of controlling  
channel and number keys through the TV or VCR. Refer to section F for programming the  
channel and number keys through your TV or VCR.  
STEP4 Store the three-digit code number  
by pressing the same [DEVICE]  
button once again. The device LED  
will blink twice to confirm that the  
code has been stored.  
STEP2 Press the [SYSTEM] button and the  
[ENTER] button simultaneously for 3  
seconds. The [STB] button will turn  
on for 20 seconds.  
STEP1 Press the [DEVICE] button (TV, VCR or  
AUX) you wish to verify and the  
[ENTER] button simultaneously for 3  
seconds.  
Volume Default : STB volume and mute through the TV , with the option of controlling volume  
and mute through the STB or AUDIO.  
Refer to section G for programming the volume and mute through your STB or AUDIO.  
STB : TV  
TV : TV  
VCR : TV  
AUX : AUX  
STEP3 Press the [DEVICE] button and the  
[POWER] button you wish to store  
in the System On/Off button and  
repeat this until you stored all the  
power commands into the System  
On/Off button.  
lf you wish to store the STB volume control  
in STB mode, use the following steps.  
*Note : Try all the functions on the remote  
control. If any of the functions do  
not work as they should, repeat from  
Step 2 using the next three-digit code  
number from the same brand list.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
System On/Off button :  
Universal Remote Control, Inc.  
This button is designed to send out power commands for two, three or all four devices with one  
button press. Please refer to section E for details.  
STEP1 Press the [STB] button and the  
[ENTER] button simultaneously  
for 3 seconds.  
OEE-0050B Rev 15 (08/17/11)  
STEP2 Press the [INFO] button.  
 

Moyer Diebel Dishwasher MD1000HT User Manual
MTD Log Splitter 241 640A User Manual
NAD Stereo Amplifier PP 3 User Manual
NETGEAR Switch JFS516 User Manual
Nokia Cell Phone 3285 User Manual
NordicTrack Home Gym 831236652 User Manual
Olympus Camera Lens TCON 14 User Manual
Oreck Vacuum Cleaner BB1000 User Manual
P3 International Home Security System P8315 User Manual
Panasonic Microwave Oven F00039X90KT User Manual