One for All Universal Remote SV 1100 User Manual

Introduction  
The ONE FOR ALL Remote Control Blaster (SV-1100) converts the Infra-Red (IR) signals from your Remote  
Control into Radio-Frequency (RF) allowing you to control your devices through doors, windows, floors  
and walls without having to worry about line of sight requirements (up to 30 metres, room to room).  
Simply connect the included RECEIVER to the corresponding device to receive the RF signals.  
NOTE: this product may not work with remotes with metal housing or displays  
This Package contains  
A
B
C
D
E
RF TRANSMITTER  
2/3 size AAA rechargeable battery  
AA size sleeve (if your remote control requires AA batteries)  
RECEIVER  
IR Eye cord cord (3 IR eyes, 2 Metres long)  
Power Adaptor  
F
Installing the SV-1100 in 3 easy steps  
Simply install the RF transmitter instead of one of the AAA or AA  
batteries inside your remote control.  
1
2
NOTE: You may have to change the position of the RF transmitter to have better  
RF performance.  
Set the Selection Switch (on the back of the RECEIVER) to…  
A : 58KHz (for few and very specific remotes)  
B : 38KHz (most remote controls)  
C : Sensitivity lower e.g. other equipment using 433.92MHz (external  
interference).  
See section: “Interference”.  
3.1 Place the RECEIVER next to the corresponding device(s) you wish to control.  
3
3.2 Connect the IR Eye cord plug to the back of the RECEIVER and place the IR  
Eye on the receiving window (IR sensor) of the corresponding device.  
NOTE: There are 3 IR Eyes to control 3 separate devices.  
NOTE: Remove the adhesive tape on the bottom of the IR Eye to secure it on the  
front of the audio/video equipment IR sensor.  
3.3 Plug the Power adaptor in the wall socket and connect the DC connector  
to the back of the RECEIVER. The POWER LED on the top of the RECEIVER  
will illuminate.  
WWW.ONEFORALL.COM  
4
 
Interference  
The RECEIVER can be interfered with an external RF signal. The LED (A/B) of  
the RECEIVER will blink even without pressing a key on the remote control.  
If this is the case, please try the below:  
1. Try to move the RECEIVER.  
2. Reduce the antenna length.  
3. Set the switch to position “C”.  
Recharging the (2/3 AAA size) Battery  
Your RECEIVER is also the recharging-station for the included (2/3 AAA size) battery.  
If your remote control is functioning at a shorter distance than normally (when the LED  
(A/B) of the RECEIVER does not blink when a key on the remote control is being pressed)  
then the battery needs to be recharged.  
1. Remove the (2/3 AAA size) battery from your remote control.  
2. Place the (2/3 AAA size) battery in the compartment that you can find on the bottom  
of the RECEIVER. The LED (BAT) will light up.  
3. The LED will switch off as soon as the (2/3 AAA size) battery is fully charged.  
NOTE: The RF operating range may vary depending on the overall battery charge (e.g.  
you may have to replace the alkaline batteries if the operating range decreases).  
Caution: Use only with supplied rechargeable battery. Risk of explosion if battery is  
installed by an incorrect type.  
5
WWW.ONEFORALL.COM  
 

NEC Personal Computer PA322UHD User Manual
Newcon Optik Microscope Magnifier YUNNAT 2P 3 User Manual
Nikon Camcorder D40x User Manual
Nikon Camcorder S4400 User Manual
Nikon Digital Camera 26442 User Manual
Optoma Technology Projection Television HDBV5100P User Manual
Optoma Technology Projector Accessories GT750 User Manual
Panasonic Speaker System AJ SD955BE User Manual
Panasonic Switch EVQ11 User Manual
Paradyne Network Card 8610 User Manual