One for All Universal Remote ONE FOR ALL User Manual

FEATURE - FUNCTION  
The Light (LED) flashes red to show  
URC 5800  
Cinema 5+  
that the remote is working and is sending a signal.  
The SETUP key is used to program your  
Cinema 5.  
The POWER key controls power ON and OFF the  
same as the POWER key on your original remote.  
Please note that most CD Players do not have an  
ON/OFF function on the original remote control. If  
this is the case with your CD Player, then POWER  
will have no effect on your CD Player.  
User Guide  
OVERVIEW  
®
Thank you for purchasing the One For All Cinema 5 uni-  
versal remote control with learning. Along with being a com-  
plete Home Theater universal remote, the Cinema 5’s  
sophisticated technology will allow you to finally consolidate  
the clutter of all of the original remotes in your home enter-  
tainment system. Through patented learning technology, you  
can teach your Cinema 5 the unique features of your original  
remotes and create the complete universal remote control –  
only from One For All.  
The TV, VCR, CBL/SAT, DVD/LD or RCVR keys  
are used to select the home entertainment compo-  
nent you want to control. If your component does  
not respond when you press a key on the remote  
control, press the appropriate device key (TV,  
VCR, CBL/SAT, DVD/LD or RCVR) first to tell the  
remote control which component you would like  
the remote to operate.  
Before you can use your new remote control, you will need  
to program it to operate the specific home entertainment  
components you wish to control. Follow the instructions  
detailed in this manual to set up your Cinema 5 and enjoy  
your new remote control.  
The VOL (Volume Up), VOL (Volume Down)  
and MUTE keys control the volume the same as  
the Volume Up and Down and Mute keys on your  
original remote.  
FEATURES AND FUNCTIONS  
The illustration below and the chart on the next three pages  
describe the features and functions of the Cinema 5 univer-  
sal remote control. Use the drawing to locate each feature of  
the remote, then refer to the chart for a description of what  
function each feature performs.  
The CH (Channel Up) and CH (Channel  
Down) keys change channels the same as the  
Channel Up and Down keys on your original  
remote. The CH  
/
keys also control the fol-  
lowing functions in other modes: DVD/LD  
mode = Skip Forward/ Skip Reverse, RCVR, AUX  
and CD mode = Preset Up/Preset Down.  
CBL/SAT  
The Digit keys (0-9) control direct channel access  
the same as the Digit keys on your original  
remote. The Digit keys (0-9) may also control the  
following functions in other modes: RCVR and  
AUX modes = Input Selections.  
RCVR  
DVD/LD  
The ENTER key operates the same as the Enter  
key on your original remote. If your original remote  
control required you to use an Enter key to change  
channels, use the ENTER key on the Cinema 5  
after entering your channel number. The ENTER  
key may also control the following functions in  
other modes: RCVR and AUX modes = TAPE  
MON.  
The PREV CH (Previous Channel) key operates  
the same as the Last Channel or Recall key on  
your original remote. The PREV CH key may also  
control the following functions in other modes:  
DVD/LD, RCVR and CD mode = Random.  
The CH / , VOL / , MUTE, PREV CH  
and Digit (0-9) keys are made of a phosphores-  
cent material that glows-in-the-dark. Expose the  
keys to bright light to activate the glow-in-the-dark  
feature. The length of time the keys remain illumi-  
nated will be determined by the length of time the  
remote is exposed to bright light.  
SET  
 
Locate the brand name of your TV in the “Setup Codes For  
TVs” section (starting on the next page), and write it in the  
space below.  
Electroband  
Emerson  
0000, 0185  
0463, 0236, 0180, 0019, 0154, 0177,  
0178, 0179, 0185, 0282, 0039, 0624  
Envision  
Fisher  
Fujitsu  
Funai  
Futuretech  
GE  
0030  
0154, 0159  
0179  
0171, 0179, 0180  
TV Brand:__________________________________________  
The brands are listed in alphabetical order with the most  
popular codes listed first. You will use one of these codes to  
program your Cinema 5 to operate your TV as follows:  
0180  
0047, 0051, 0451, 0021, 0178, 0282,  
0135, 1147, 1347  
0019, 0030, 0017  
0019, 0030, 0178, 0039  
0053, 0056  
0179, 0180  
0178  
0180  
0145, 0151, 0056  
0054  
0054  
0000  
0053  
0180  
0019, 0030  
0024  
1.  
2.  
Turn on your TV.  
Gibralter  
Goldstar  
Gradiente  
Grunpy  
Hallmark  
Harvard  
Hitachi  
Infinity  
JBL  
JCB  
JVC  
KEC  
Kenwood  
Kloss  
On the Cinema 5, press TV and release. Press  
and hold SETUP until the red light blinks twice,  
then release SETUP.  
3.  
4.  
Enter the first four-digit TV code listed for your  
brand. If performed correctly, the red light will blink  
twice when you enter the final digit.  
Aim the Cinema 5 at your TV and press POWER.  
The TV should turn off. If it does not respond,  
repeat steps 2-4, trying each code listed for your  
brand until you find the one that operates your TV.  
NOTE: If you have tried all the codes listed for  
your brand and your TV does not respond, try  
using ”SEARCHING FOR YOUR CODE”.  
KTV  
LG  
Logik  
0030, 0180, 0185, 0032  
0056  
0016  
Luxman  
LXI  
Magnasonic  
0056  
5.  
Your Cinema 5 is now programmed to operate  
your TV. Write your TV code in the boxes to the left  
for future reference.  
0047, 0054, 0154, 0156, 0178  
0179, 0030, 0092, 0093, 0019, 0003,  
0054, 0156  
Magnavox  
Majestic  
Marantz  
Matsushita  
Megatron  
MEI  
0054, 0096, 0187, 0030, 0179, 0171  
0016  
0054, 0030  
0250  
0145, 0178  
0185  
Remember, if you want to use your Cinema 5 to operate  
Memorex  
MGA  
Midland  
Minutz  
0056, 0150, 0154, 0016, 0178  
0150, 0019, 0030, 0178  
0017, 0047, 0051, 0135, 0039  
0021  
your TV, press the TV key first.  
Setup Codes For TVs  
Mitsubishi  
Motorola  
MTC  
Multitech  
NAD  
NEC  
Nikko  
NTC  
Onwa  
Optimus  
Optonica  
Orion  
Panasonic  
Penney  
0150, 0093, 0019, 0178  
0093  
0060, 0019, 0030, 0056, 0185  
0180  
0156, 0166, 0178  
0019, 0030, 0056  
0030, 0092, 0178  
0092  
0180  
0250, 0154, 0166  
0093, 0165  
0236, 0436  
0250, 0051  
0047, 0156, 0051, 0030, 0019, 0021,  
0060, 0135, 0178, 0039, 1347  
0054, 0145, 0096, 0019, 0030  
0054  
0019, 0030, 0039  
0166  
0092, 0019, 0039  
0051  
0047  
Admiral  
Aiko  
Akai  
Alaron  
Ambassador  
Ampro  
0093, 0179, 0180, 0016, 0047  
0092  
0030  
0179  
0177  
0751  
0180  
0019, 0185, 0003  
0451, 0092, 0180, 0003  
0180  
0017, 0030, 0179  
0019  
0154, 0016  
0180  
0019  
0056, 0030  
0030  
0054  
0000  
0451, 0092  
0060, 0092, 0030, 0056, 0039  
0185  
0056  
0180, 0185  
0180  
0180, 0039  
0030, 0060, 0154, 0039, 0466, 1147, 1347  
0180  
0451, 0092, 0019, 0039, 0624  
0019  
0145  
0017, 0019  
0720, 0774  
Anam  
AOC  
Audiovox  
Baysonic  
Beaumark  
Belcor  
Bell & Howell  
Bradford  
Brockwood  
Candle  
Carnivale  
Carver  
Celebrity  
Cineral  
Citizen  
Clairtone  
Concerto  
Contec  
Craig  
Crown  
Curtis Mathes  
CXC  
Daewoo  
Daytron  
Denon  
Dumont  
Dwin  
Philco  
Philips  
Pilot  
Pioneer  
Portland  
Prism  
Proscan  
Proton  
Pulsar  
0178, 0466  
0017, 0019  
Quasar  
RadioShack  
0250, 0051, 0165  
0047, 0056, 0154, 0019, 0030, 0165,  
0178, 0180, 0039  
0047, 0019, 0090, 0135, 1047, 1147,  
1247, 1347  
0056, 0154, 0019, 0030, 0165, 0178,  
0180, 0039  
0185  
RCA  
Realistic  
Rhapsody  
Runco  
Sampo  
0017, 0030, 0603  
0030, 0039  
 
Samsung  
Samsux  
Sansei  
Sanyo  
0060, 0019, 0030, 0056, 0178, 0039  
0039  
0451  
0154, 0159  
NOTE: If you have tried all the codes listed for  
your brand and your VCR does not respond, try  
using “SEARCHING FOR YOUR CODE”.  
Scimitsu  
Scotch  
Scott  
0019  
0178  
5.  
Your Cinema 5 is now programmed to operate  
your VCR. Write your VCR code in the boxes to  
the left for future reference.  
0236, 0019, 0178, 0179, 0180  
Sears  
0047, 0054, 0056, 0154, 0156, 0171,  
0178, 0159, 0179  
Semivox  
Semp  
0180  
0156  
Sharp  
0093, 0165, 0039  
Remember, if you want to use your Cinema 5 to operate  
Shogun  
Signature  
Simpson  
Sony  
Soundesign  
Squareview  
SSS  
0019  
0016  
0187  
0000  
0178, 0179, 0180  
0171  
0019, 0180  
0180  
0000  
0054, 0096, 0030  
0171  
0093  
0250, 0051  
0179  
0051, 0056  
0054, 0056, 0060, 0092, 0150, 0016,  
your VCR, press the VCR key first.  
Setup Codes For VCRs  
Admiral  
Adventura  
Aiko  
0048, 0121, 0184, 0039, 0060, 0202  
0000  
0278  
Aiwa  
Akai  
0037, 0000  
0041  
Starlite  
American High 0035  
Supreme  
Sylvania  
Symphonic  
Tandy  
Technics  
Technol Ace  
Techwood  
Teknika  
Asha  
0240  
Audiovox  
Beaumark  
Bell & Howell  
Broksonic  
Calix  
0037  
0240  
0104  
0184, 0209, 0479, 0002, 0121  
0037  
Canon  
0035  
Carver  
0081  
0019, 0179, 0180, 0039  
0056  
0056, 0177, 0178  
0156, 0060, 0154  
0185  
CCE  
0072, 0278  
Telefunken  
TMK  
Toshiba  
Tosonic  
Totevision  
Vector Research 0030  
Victor  
Vidikron  
Vidtech  
Viking  
Cineral  
0278  
Citizen  
0037, 0278  
Colt  
0072  
Craig  
0072, 0240, 0037, 0047, 0271  
0039  
Curtis Mathes  
Cybernex  
Daewoo  
Denon  
0035, 0041, 0060, 0202  
0240  
0278, 0045  
0042  
0053  
0054  
0019, 0178  
0046  
0016, 0019, 0030, 0054, 0056, 0096,  
0165, 0178, 0179, 0021  
Dynatech  
Electrohome  
Electrophonic  
Emerex  
Emerson  
0000  
0037  
0037  
0032  
Wards  
White  
0209, 0184, 0479, 0278, 0000, 0002,  
Westinghouse 0451, 0463, 0236, 0180, 0624  
Yamaha  
Zenith  
0036, 0037, 0043, 0068, 0121, 0184, 0212  
0019, 0030  
0017, 0092, 0016  
Fisher  
Fuji  
Funai  
0104, 0047, 0066  
0033, 0035  
0000  
Programming the Cinema 5 to operate your VCR:  
Garrard  
GE  
Goldstar  
Go-Video  
Gradiente  
0000  
Locate the brand name of your VCR in the “Setup Codes For  
VCRs” section (starting below), and write it in the space  
below.  
0060, 0035, 0048, 0240  
0037, 0038  
0432, 0526  
0000  
VCR Brand: ________________________________________  
Harley Davidson 0000  
Harman/Kardon 0038  
The brands are listed in alphabetical order with the most pop-  
ular codes listed first.You will use one of these codes to pro-  
gram your Cinema 5 to operate your VCR as folllows:  
Harwood  
Headquarter  
HI-Q  
0072, 0068, 0072  
0046  
0047  
Hitachi  
Jensen  
JVC  
KEC  
Kenwood  
KLH  
0041, 0000, 0042  
0041  
0041, 0067  
0037, 0278  
0038, 0041, 0067  
0072  
1.  
2.  
Turn on your VCR and play a tape.  
On the Cinema 5, press VCR and release. Press  
and hold SETUP until the red light blinks twice, then  
release SETUP.  
Kodak  
Lloyd’s  
Logik  
0035, 0037  
0000, 0208  
0072  
0037  
0278, 0179, 0171, 0020, 0037, 0072, 0240  
0035, 0081, 0000, 0039, 0110, 0149  
0240  
0035, 0081  
3.  
4.  
Enter the first four-digit VCR code listed for your  
brand. If you perform this procedure correctly, the  
red light will blink twice when entering the final  
digit.  
LXI  
Magnasonic  
Magnavox  
Magnin  
Marantz  
Marta  
Matsushita  
MEI  
Memorex  
Aim the Cinema 5 at your VCR and press  
POWER.Your VCR should turn off. If your original  
VCR remote control did not have a POWER key,  
press STOP. Your VCR should stop. If your VCR  
does not respond, repeat steps 2-4, trying each  
code listed for your brand until you find the one that  
operates your VCR.  
or  
0037  
0162, 0035, 0454  
0035  
0162, 0240, 0035, 0037, 0104, 0000,  
 
0039, 0046, 0047, 0048, 1037, 1062,  
1162, 1262  
Programming the Cinema 5 to operate your TV/VCR  
Combo:  
MGA  
0043, 0240  
Locate the brand name of your TV/ VCR Combo in the  
“Setup Codes For TV/ VCR Combos” section (starting on the  
next page), and write it in the space below.  
MGN Technology 0240  
Minolta  
Mitsubishi  
Motorola  
MTC  
0042  
0043, 0048, 0067  
0035, 0048  
0240, 0000  
TV/VCR Combo Brand: ____________________________  
Multitech  
NEC  
Nikko  
Noblex  
Olympus  
Optimus  
0000, 0072  
0038, 0041, 0067, 0104  
0037  
0240  
The brands are listed in alphabetical order with the most  
popular codes listed first. You will use one of these codes to  
program your Cinema 5 to operate your TV/VCR Combo as  
follows:  
0035  
0162, 0048, 0037, 0104, 0454, 1037,  
1062, 1162, 1262  
0209, 0184, 0479, 0002  
0162, 0035, 0077, 0225, 0454, 1062,  
1.  
2.  
Turn on your TV/VCR Combo.  
Orion  
Panasonic  
Press VCR and release. Press and hold SETUP  
until the Cinema 5’s red light blinks twice, then  
release SETUP.  
1162, 1262  
Penney  
Pentax  
Philco  
Philips  
Pilot  
Pioneer  
Proscan  
Protec  
Pulsar  
Quarter  
Quartz  
Quasar  
RadioShack  
Radix  
0035, 0037, 0038, 0042, 0240  
0042  
0035, 0209, 0479  
0035, 0081, 0110  
0037  
0067, 0162  
0060, 0202  
0072  
3.  
4.  
Enter the first four-digit TV/VCR code listed for  
your brand in the “Setup Codes For TV/VCR  
Combos” section. If you perform this procedure  
correctly, the red light will blink twice when you  
enter the final digit of your code.  
Aim the Cinema 5 at your TV/VCR Combo and  
press POWER. The unit should turn off. If it does  
not respond, Repeat steps 2-4, trying each code  
listed for your brand until you find the one that oper-  
ates your TV/VCR Combo.  
0039  
0046  
0046  
0162, 0035, 0077, 0454, 1062, 1162, 1262  
0000, 0037, 1037, 1062, 1162, 1262  
0037  
0037  
0060, 0240, 0042, 0035, 0048, 0077, 0149  
0000, 0035, 0037, 0046, 0047, 0048,  
NOTE: If you have tried all the codes listed for  
your brand and your TV/VCR Combo does not  
respond, try using “SEARCHING FOR YOUR  
CODE”.  
Randex  
RCA  
Realistic  
0066, 0104  
Runco  
Samsung  
Sanky  
Sansui  
Sanyo  
Scott  
0039  
0240, 0045  
0048, 0039  
0000, 0041, 0067, 0271, 0479  
0104, 0046, 0047, 0054, 0240  
0043, 0045, 0121, 0184, 0210  
5.  
Your Cinema 5 is now programmed to operate  
your TV/VCR Combo. Write your TV/VCR Combo  
code in the boxes to the left for future reference.  
Sears  
0000, 0035, 0037, 0042, 0046, 0047,  
0066, 0104  
Remember, to use your Cinema 5 to operate your TV/VCR  
Semp  
0045  
Combo, press the VCR key first.  
Sharp  
0048  
0072  
0240  
0072  
Setup Codes For TV/VCR Combos  
Shintom  
Shogun  
Singer  
Sony  
STS  
Sylvania  
Symphonic  
Tatung  
TEAC  
Technics  
Teknika  
Thomas  
TMK  
American High 0035*  
Brocksonic  
Colt  
0002, 0294, 0479  
0072  
0032, 0033, 0000, 0035  
0042  
0035, 0081, 0043, 0000, 0110  
0000  
0041  
0000, 0041  
0162, 0035  
0000, 0035, 0037  
0000  
0240, 0036, 0208  
0043, 0045, 0066, 0210  
0037, 0240  
Curtis Mathes  
Daewoo  
Emerson  
Funai  
0035*  
0278*  
0002, 0294, 0479  
0000  
GE  
Hitachi  
HQ  
0035*, 0060*, 0048*, 0240  
0035*, 0000  
0000  
Lloyds  
0000  
Magnavox  
Magnin  
Memorex  
MGA  
0000, 0035*, 0081*  
0240  
0037, 0162*  
0240  
Toshiba  
Totevision  
Unitech  
0240  
Mitsubishi  
Orion  
Panasonic  
Penney’s  
Quasar  
RCA  
0048*  
Vector Research 0038  
Vector 0045  
Video Concepts 0040, 0045  
0002, 0294, 0479  
0035*, 0162*  
0035*, 0240, 0162*  
0035*, 0162*  
0035*, 0060*, 0048*  
0000, 0479  
0240  
Videosonic  
Wards  
0240  
0000, 0035, 0042, 0047, 0048, 0060,  
0072, 0081, 0149, 0240  
Sansui  
Sanyo  
White  
Westinghouse 0278, 0479, 0209, 0184  
Sears  
Sony  
Symphonic  
Zenith  
0000, 0037  
0032*  
0000  
XR-1000  
Yamaha  
Zenith  
0000, 0035, 0072  
0038  
0039, 0000, 0033  
0000  
 
NOTE: If your TV/VCR works with one of the above codes  
highlighted with an asterisk (*), you may need to program a  
separate TV code to control the volume. Check the list of  
codes below and follow the instructions in the “Programming  
the Cinema 5 to Operate Your TV” section to program the  
supplied TV code.  
Setup Codes for Cable Converters  
ABC  
0003, 0008, 0014, 0007, 0001, 0011,  
0013, 0017  
0153, 0315  
0022, 0207  
0797, 0153, 0022, 0207  
0056  
Allegro  
Gantronix  
Archer  
Belcor  
TV/VCRs working on VCR code 0032 may require  
TV code 0000 for volume control.  
TV/VCRs working on VCR code 0035 may require  
TV code 0051 for volume control.  
TV/VCRs working on VCR code 0048 may require  
TV code 0093 for volume control.  
TV/VCRs working on VCR code 0060 may require  
TV code 0047 for volume control.  
TV/VCRs working on VCR code 0081 may require  
TV code 0054 for volume control.  
TV/VCRs working on VCR code 0162 may require  
TV code 0250 for volume control.  
TV/VCRs working on VCR code 0278 may require  
TV code 0451 for volume control.  
Cable Star  
Cabletenna  
Cableview  
Century  
Citizen  
Colour Voice  
Comtronics  
Contec  
0056  
0022  
0022  
0153  
0153, 0315  
0031  
0040  
0019  
Digi  
0637  
Eastern  
Emerson  
Everquest  
Focus  
0002  
0797  
0015, 0040  
0400  
Garrard  
0153  
GC Electronics 0056, 0207  
Programming the Cinema 5 to operate your Cable  
Converter or Satellite Receiver:  
Gemini  
0015  
General  
Locate the brand name of your Cable Converter or Satellite  
Receiver in the “Setup Codes for Cable Converters” or “Setup  
Codes for Satellite Receivers” section (starting on the next  
page), and write it in either space below.  
Instrument  
0476, 0003, 0014, 0011, 0276, 0810  
Goldstar  
Goodmind  
Hamlin  
0144, 0040  
0797  
0259, 0009, 0020, 0034  
Hitachi  
Hytex  
Jasco  
Jerrold  
0011  
0007  
Cable Converter Brand:____________________________________________________________________________________  
________________________________________________  
0153, 0315, 0015  
0476, 0003, 0014, 0011, 0012, 0015, 0810  
or  
Linsay  
0440  
0027, 0014  
0000  
0063, 0156  
0618  
0063, 0156  
0007, 0019  
0021  
0021, 0107, 0000  
0637  
0000  
0153, 0027, 0031  
0144, 0023, 0533  
Satellite Receiver Brand:______________________________  
________________________________________________  
Magnavox  
Memorex  
Movie Time  
Novaplex  
NSC  
The brands are listed in alphabetical order with the most pop-  
ular codes listed first.You will use one of these codes to pro-  
gram your Cinema 5 to operate your Cable Converter or  
Satellite Receiver as follows:  
Oak  
Optimus  
Panasonic  
Panther  
Paragon  
Philips  
Pioneer  
Popular  
Mechanics  
Prelude  
Pulsar  
RadioShack  
RCA  
Realistic  
Recoton  
Regal  
1.  
Turn on your Cable Converter or Satellite  
Receiver.  
2.  
Press CBL/SAT and release. Press and hold SETUP  
until the Cinema 5’s red light blinks twice, then  
release SETUP.  
0400  
0770  
0000  
3.  
4.  
Enter the first four-digit Cable Converter or  
Satellite Receiver code listed. If you perform this  
procedure correctly, the red light will blink twice  
when you enter the final digit of your code.  
0015, 0315, 0797, 0833  
0021  
0207  
0400  
0259, 0020  
0002  
0011  
0000  
0144, 0040  
Aim the Cinema 5 at your Cable Converter or  
Satellite Receiver and press POWER.Your Cable  
Converter or Satellite Receiver should turn off. If it  
does not respond, repeat steps 2-4, trying each  
code listed for your brand until you find the one  
that operates your Cable Converter or Satellite  
Receiver.  
Regency  
Rembrandt  
Runco  
Samsung  
Scientific Atlanta 0477, 0008, 0017  
Seam  
Signal  
0510  
0015, 0040  
0011  
0040  
0021  
0003, 0015  
0015, 0040, 0797  
0015  
0001  
0258  
NOTE: If you have tried all the codes listed for  
your brand and your Cable Converter or Sateliite  
Receiver does not respond, try using “SEARCH-  
ING FOR YOUR CODE”.  
Signature  
SL Marx  
Sprucer  
Starcom  
Stargate  
Starquest  
Sylvania  
Tandy  
5.  
Your Cinema 5 is now programmed to operate  
your Cable Converter or Satellite Receiver. Write  
your Cable Converter or Satellite Receiver code in  
the boxes to the left for future reference.  
Teleview  
Texscan  
TFC  
Timeless  
Tocom  
0040  
0001  
0310  
0418  
Remember, if you want to use your Cinema 5 to operate  
your Cable Converter or Satellite Receiver, press the  
CBL/SAT key first.  
0012, 0013  
 
Toshiba  
Tusa  
TV86  
0000  
0015  
0063  
0153, 0022, 0207  
5.  
Your Cinema 5 is now programmed to operate your  
DVD or Laser Disc Player. Write your DVD or Laser  
Disc Player code in the boxes to the left for future ref-  
erence.  
Unika  
United Artists  
United Cable  
Universal  
Videoway  
Viewstar  
Zenith  
0007  
0003  
0153, 0022, 0056, 0191, 0207  
0250  
0063, 0027, 0258  
0525, 0000, 0015, 0207, 0008  
0400  
Remember, to use Cinema 5 to operate your DVD or Laser  
Disc Player, press the DVD/LD key first.  
Setup Codes for DVD Players  
Zentek  
JVC  
0558  
Setup Codes for Satellites  
Kenwood  
Magnavox  
Mitsubishi  
Onkyo  
0534  
0503  
0521  
0503  
AlphaStar DBS 0772  
Chaparral  
Echostar DBS  
ExpressVu DBS 0775  
General  
Instrument  
Hitachi DBS  
HTS DBS  
Hughes Network  
Systems DBS 0749  
Jerrold Primestar 0627  
0216  
0775  
Panasonic  
Philips  
Pioneer  
Proscan  
RCA  
0490  
0539, 0503  
0525, 0571  
0522  
0361, 0627, 0869  
0819  
0775  
0522  
Samsung  
Sony  
0573  
0533  
Technics  
Toshiba  
Yamaha  
Zenith  
0490  
0503  
0490, 0545  
0503  
Jerrold  
JVC  
0361  
0775  
Magnavox DBS 0722, 0724  
Memorex DBS 0724  
Panasonic DBS 0701  
Philips DBS  
Primestar  
Proscan  
RCA DSS  
Sony DBS  
Star Choice DBS 0869  
Setup Codes for Laser Disc Players  
0722, 0724  
0361, 0627  
0566  
0566, 0143, 0855  
0639  
Denon  
Mitsubishi  
NAD  
0059  
0059  
0059  
Pioneer  
Sony  
0059  
0193, 0201  
Programming the Cinema 5 to operate your Receiver/Tuner:  
STS  
0210  
0790  
0724, 0722  
0856  
Locate the brand name of your Receiver/Tuner in the “Setup  
Codes For Receiver/Tuners” section (starting below), and  
write it in below.  
Toshiba DBS  
Uniden DBS  
Zenith  
Receiver/Tuner Brand:________________________________  
Programming the Cinema 5 to operate your DVD or  
Laser Disc Player:  
The brands are listed in alphabetical order with the most  
popular codes listed first. You will use one of these codes to  
program your Cinema 5 to operate your Receiver/Tuner as  
follows:  
Locate the brand name of your DVD or Laser Disc Player in  
the DVD or Laser Disc Player setup codes (starting below),  
and write it in the space below.  
1.  
2.  
Turn on your Receiver/Tuner.  
DVD/LD Player Brand:________________________________  
Press RCVR and release. Press and hold SETUP  
until the Cinema 5’s red light blinks twice, then  
release SETUP.  
The brands are listed in alphabetical order with the most pop-  
ular codes listed first.You will use one of these codes to pro-  
gram your Cinema 5 to operate your DVD or Laser Disc  
Player as follows:  
3.  
4.  
Enter the first four-digit Receiver/Tuner code listed  
for your brand in the “Setup Codes For  
Receivers/Tuners” section. If performed correctly,  
the red light will blink twice when you enter the  
final digit.  
1.  
Turn on your DVD or Laser Disc Player and insert  
a disc.  
2.  
Press DVD/LD and release. Press and hold  
SETUP until the Cinema 5’s red light blinks twice,  
then release SETUP.  
Aim the Cinema 5 at your Receiver/Tuner and press  
POWER. The unit should turn off. If it does not  
respond, repeat steps 2-4, trying each code listed  
for your brand until you find one that works.  
3.  
4.  
Enter the first four-digit DVD or Laser Disc Player  
code listed for your brand. If performed correctly,  
the red light will blink twice when entering the final  
digit.  
NOTE: If the unit still does not respond, try using  
“SEARCHING FOR YOUR CODE”.  
Aim the Cinema 5 at your DVD or LaserDisc  
Player and press POWER.Your DVD or Laser Disc  
Player should turn off. If it does not respond,  
repeat steps 2-4, trying each code listed for your  
brand until you find the one that works.  
5.  
Your Cinema 5 is now programmed to operate  
your Receiver/Tuner. Write your Receiver/Tuner  
code in the boxes to the left for future reference.  
NOTE: If you have tried all the codes listed for your  
brand and your DVD or Laser Disc Player does not  
respond, try using ‘SEARCHING FOR YOUR  
CODE”.  
 
Remember, to use your Cinema 5 to operate your  
Receiver/Tuner, press the RCVR key first.  
4.  
5.  
Slowly alternate between pressing POWER* and  
TV until your TV turns OFF. Make sure that the  
Cinema 5 is aimed at your TV during the search.  
You may have to press this sequence of buttons  
(POWER* then TV) up to 100 times to search the  
entire library of codes.  
Setup Codes For Receivers/Tuners  
ADC  
Akai  
Aiwa  
0531  
0076  
0121, 0158, 0189, 0405  
Bang & Olufsen 0898  
When your TV turns OFF, press and release  
SETUP to lock in the code for your TV.Your  
Cinema 5 is now programmed to operate your TV.  
Capetronic  
Carver  
0531  
0008, 0042, 0189, 0360  
Casio  
0195  
Clarinette  
Curtis Mathes  
Denon  
Fisher  
Garrard  
0195  
0039, 0080  
0004  
0042, 0360  
0463  
*If you are searching for your VCR, CD, LD or DVD Player  
code, you may want to play a tape or disk and use the STOP  
key instead of the POWER key to search for your code.  
When your VCR stops, press SETUP to lock in your code.  
NOTE: To search for the codes of your other components,  
repeat Steps 1 through 5, only substitute the appropriate  
device key (ie., VCR, DVD/LD, RCVR, CD or CBL/SAT) for  
the component you are searching for.  
Harman/Kardon 0110, 0891, 0189  
JBL  
0110  
JVC  
0074  
Kenwood  
Linn  
0027, 0313, 0314, 0186, 0042  
0189  
Lloyd’s  
LXI  
Magnavox  
Marantz  
MCS  
Modulaire  
NAD  
Nakamichi  
Onkyo  
Optimus  
0195  
0181  
RETRIEVING THE CODES PROGRAMMED INTO THE  
Cinema 5  
0189, 0195, 0531, 0391  
0039, 0189  
0039  
0195  
0320  
0097  
0135, 0380  
0042, 0080, 0181, 0186, 0531, 0670,  
0738, 0801  
0039, 0309, 0518  
0195  
0189  
0014*, 0080*, 0150, 0531, 0630, 1023  
0039  
0054, 0360, 0531, 0530  
0181, 0195  
0189  
0322  
0186  
0491, 0502  
If you have set up the Cinema 5 using the “SEARCHING  
FOR YOUR CODE” procedure, you may want to figure out  
which four-digit code is operating your equipment. Use this  
procedure after you have set up your components to find out  
which four-digit code is operating your equipment. For exam-  
ple, to find out which code is operating your TV after setting  
up your TV using the “SEARCHING FOR YOUR CODE”  
procedure:  
Panasonic  
Penney  
Philips  
Pioneer  
Quasar  
RCA  
Realistic  
Sansui  
Scott  
1.  
Press TV and release. Press and hold SETUP until  
the Cinema 5’s red light blinks twice, then release  
SETUP.  
2.  
3.  
Press 9 - 9 - 0.  
For the first digit of your four-digit code, press 1  
and count the number of times the red light (LED)  
blinks on the Cinema 5. If the light does not blink  
when you press the number 1, the digit is zero.  
Sharp  
Sherwood  
Sony  
0158**, 0474  
Soundesign  
TEAC  
Technics  
Victor  
Wards  
Yamaha  
Yorx  
0670  
0463  
0039, 0309, 0518  
0074  
0014, 0042, 0054, 0080, 0158, 0189  
0176, 0186  
0195  
4.  
5.  
6.  
For the second digit, press 2 and count the num-  
ber of times the red light (LED) blinks on the  
Cinema 5. If the light does not blink when you  
press the number 2, the digit is zero.  
For the third digit, press 3 and count the number  
of times the red light (LED) blinks on the Cinema  
5. If the light does not blink when you press the  
number 3, the digit is zero.  
Zenith  
0857  
*May use Amplifier code 0013 for power and volume. See  
page 21 for amplifier setup and codes.  
For the fourth and final digit, press 4 and count the  
number of times the red light (LED) blinks on the  
Cinema 5. If the light does not blink when you  
press the number 4, the digit is zero. Now you  
have your four-digit code.  
**May use Misc. Audio code 0159 to operate surround and  
tuner presets. See page 24 for misc. audio setup and codes.  
SEARCHING FOR YOUR CODE  
NOTE: To find out the code for your other components,  
repeat Steps 1 through 6, only substitute the appropriate  
device key (VCR, DVD/LD, RCVR, CD or CBL/SAT) for the  
component code you wish to learn.  
If your TV, VCR or Cable Converter does not respond to the  
Cinema 5 after trying all of the codes listed for your brand, or if  
your brand is not listed at all, try searching for your code. For  
example, after trying all of the codes for your TV, you still can-  
not get the Cinema 5 to operate your TV, then:  
LEARNING FUNCTIONS ONTO THE 1L, 2L, 3L AND 4L  
KEYS  
1.  
2.  
Turn on your TV.  
Press TV and release. Press and hold SETUP until  
the Cinema 5’s red light blinks twice, then release  
SETUP.  
The 1L, 2L, 3L and 4L keys can be used to customize those  
functions that are unique to your home entertainment needs.  
For example, the Cinema 5 does not offerTracking Up or  
Down for a VCR. With the learning feature on the Cinema 5,  
you can add these functions and many others learned from  
your original remote control.  
3.  
Press 9 - 9 - 1.  
 
NOTE: Please have your original remote controls handy before  
performing learning on the Cinema 5.  
SETTING UP OTHER COMPONENTS  
In addition to the components labeled on the device keys  
(TV, VCR, DVD/LD, CBL/SAT, etc.), the Cinema 5 can also  
operate the following components: Cassette Decks, Infrared  
Home Automation, MiniDisc, Video Accessories and Miscel-  
laneous Audio Components (Graphic Equalizers and Digital  
Music Service Boxes).  
1.  
2.  
3.  
Press and hold SETUP until the Cinema 5’s red  
light blinks twice, then release SETUP.  
Press 9 - 7 - 5. The Cinema 5’s red light will blink  
twice.  
Press and release the Device key in which you want  
to learn a feature (e.g., TV).  
The Setup Codes for these components can be accessed  
under the following device keys:  
NOTE: Steps 4 through 6 need to be completed within 10  
seconds. Please read the next three steps before proceed-  
ing.  
Cassette Decks:  
IR Home Automation:  
MiniDisc:  
Use the VCR Key  
Use the CD Key  
Use the CD Key  
4.  
Press and release the L key in which the new fea-  
ture is to be learned. The Cinema 5’s red light will  
flash rapidly.  
Video Accessories:  
Use the CBL/SAT Key  
(Note : WebTV found under Video Accessories)  
Miscellaneous Audio: Use the AUX or RCVR Key  
For example, to set up a Cassette Player on the VCR key:  
5.  
Align your original remote control with the arrow  
mark to the left of the LED on your Cinema 5  
remote control (see diagram below)  
1.  
2.  
Turn on your Cassette Player and insert a tape.  
Press VCR and release. Press and hold SETUP  
until the Cinema 5’s red light blinks twice, then  
release SETUP.  
3.  
4.  
5.  
Enter the first four-digit Cassette Player code listed  
for your brand in the “Setup Codes For Audio  
Cassettes” section. If you perform this procedure  
correctly, the red light will blink twice when you  
enter the final digit of your code.  
NOTE: This diagram assumes that your original remote’s  
LED is in the center. It may also be off center (to the right or  
left side) If your Cinerma 7 will not take the command from  
your original, try moving the originals alignment left or right  
and see if the Cinema 5 accepts the signal from either posi-  
tion.  
Aim the Cinema 5 at your Cassette Player and  
press PL (Play).Your unit should play the tape. If it  
does not respond, repeat steps 2-4, trying each  
code listed for your brand until you find the one  
that works.  
6.  
On your original remote, press and hold the key  
(feature) you want to learn until the red light on the  
Cinema 5 blinks twice. (If the red light does not  
blink twice, stop and repeat steps 1 through 6.)  
Your Cinema 5 is now programmed to operate  
your Cassette Player.  
NOTE: You can now repeat steps 3 through 6 to learn func-  
tions on the other L keys.  
Remember, if you want to use your Cinema 5 to operate  
your Cassette Player, press the VCR key first.  
7.  
Press and hold in the SETUP key until the Cinema  
5’s red light flashes twice to lock in your new fea-  
ture. (If the red light does not blink twice, stop and  
repeat steps 1 through 6).  
Setup Codes For Audio Cassettes  
Aiwa  
0029, 0197  
Bang & Olufsen 0219  
8.  
To test the new feature, press and release the  
Device key in which the feature was learned fol-  
lowed by the L key on which the feature was  
learned.  
Carver  
Denon  
0029  
0076  
Harman/Kardon 0182  
JVC  
0244  
Magnavox  
Marantz  
Optimus  
Philips  
Pioneer  
Sansui  
Sony  
Victor  
Wards  
Yamaha  
0029  
0029  
0027, 0220  
0029  
0027, 0220  
0029  
0170, 0243, 0291  
0273  
0027  
Deleting Functions from the L Keys:  
1.  
Press and hold in the SETUP key until the Cinema  
5’s red light flashes twice and then release the  
SETUP key.  
2.  
3.  
Enter in 9 - 7 - 6.  
Press and release the Device key (e.g., TV) where  
0097  
the learned feature to be deleted is stored.  
Setup Codes For IR Home Automation  
4.  
Press the L key to be deleted twice. The Cinema  
5’s red light will blink twice after the second press  
of the L key.  
GE  
0240  
Lutron  
One For All  
RadioShack  
0318, 0597  
0167  
0240  
Security System 0167  
Universal X10  
X10  
0167  
0167  
RCVR to VCR  
SETUP* - 992 - VCR - RCVR - RCVR -  
Setup Codes For MiniDisc  
SETUP* - VCR code  
Denon  
JVC  
Onkyo  
Sharp  
Sony  
0873  
0826, 0681  
0868  
0861  
0490  
RCVR to DVD/LD  
RCVR to CBL/SAT  
CBL/SAT to TV  
SETUP* - 992 - DVD/LD - RCVR - RCVR -  
SETUP*- DVD/LD Player code  
SETUP* - 992 - CBL/SAT - RCVR -  
RCVR - SETUP* - Cable/DBS code  
SETUP* - 992 - TV - CBL/SAT -  
CBL/SAT - SETUP* - TV code  
Setup Codes For Video Accessories  
Archer 0160  
GC Electronics 0160  
Jebsee 0160  
Magnavox Web-TV 0818  
Philips Web TV 0818  
RadioShack  
TeleCaption  
Sony Web-TV  
CBL/SAT to VCR  
CBL/SAT to DVD/LD  
CBL/SAT to RCVR  
SETUP* - 992 - VCR - CBL/SAT -  
CBL/SAT - SETUP* - VCR code  
SETUP* - 992 - DVD/LD - CBL/SAT -  
CBL/SAT - SETUP* - DVD or LD code  
0160  
0171  
0850  
SETUP* - 992 - RCVR - CBL/SAT -  
CBL/SAT - SETUP* - Audio code  
*NOTE: Here (*) you must hold SETUP until the Cinema 5’s  
red light blinks twice.  
Setup Codes For Miscellaneous Audio  
Aiwa  
0010, 0159, 0404  
0052  
Fisher  
Harman/Kardon 0477  
PROGRAMMING THE MACRO KEYS  
Jerrold  
JVC  
Nikko  
RCA  
0459, 0520  
0073  
0376  
0056  
The Cinema 5 has two Macro keys (MACRO and MACRO2)  
that allow the user to play back a series of keystrokes, at any  
time, with the press of one key. For example, to set up a  
sequence that will turn on your components and change the  
components to the proper inputs:  
Scientific Atlanta 0460  
Sony  
Starcom  
0010, 0159  
0459  
1.  
Press and hold SETUP until the Cinema 5’s red  
light blinks twice, then release SETUP.  
RE-ASSIGNING DEVICE KEYS  
2.  
3.  
Press 9 - 9 - 5. The Cinema 5’s red light will blink  
twice.  
Press and release one of the MACRO keys. This  
will be the key that will play back the series of key-  
strokes assigned to that key.  
You can use the Cinema 5 to operate a second TV or a sec-  
ond VCR or any combination of seven home entertainment  
components. For example, you may want your Cinema 5 to  
control 1 TV, 1 Cable Converter, 1 Receiver, 1 CD Player, 1  
DVD Player and 2 VCRs. To accomplish this, you must re-  
assign one of the device keys to operate the desired compo-  
nent, in this case, a second VCR. The chart below shows  
you how to re-assign a particular device key and then set up  
your new component.  
4.  
Begin entering the sequence of keystrokes, up to  
15, that you wish to be played back when you  
press the MACRO key. For example:  
RCVR – POWER – TV – POWER – TV/VCR (To  
change the input on the TV to VIDEO 1) –  
CBL/SAT – POWER.  
TV to VCRSETUP* - 992 - VCR - TV - TV - SETUP*  
- VCR code  
TV to DVD/LD  
TV to RCVR  
SETUP* - 992 - DVD/LD - TV - TV -  
SETUP* - DVD or LD Player code  
5.  
Once your sequence is entered, press and hold  
SETUP until the Cinema 5’s red light blinks twice.  
SETUP* - 992 - RCVR - TV - TV -  
SETUP* - Audio code  
Now, using the example as above, whenever the pro-  
grammed MACRO key is pressed, the Receiver would power  
ON, the TV will power ON and change the input to VIDEO 1  
and then the Satellite would power ON.  
TV to CBL/SAT  
SETUP* - 992 - CBL/SAT - TV - TV -  
SETUP* - Cable/DBS code  
VCR to TVSETUP* - 992 - TV - VCR - VCR -  
SETUP* - TV code  
Repeat steps 1 - 5 to then setup a second sequence on the  
MACRO2 key.  
VCR to DVD/LD  
VCR to RCVR  
VCR to CBL/SAT  
DVD/LD to TV  
SETUP* - 992 - DVD/LD - VCR - VCR -  
SETUP* - DVD/LD Player code  
VOLUME LOCK  
SETUP* - 992 - RCVR - VCR - VCR -  
SETUP* - Audio code  
Volume Lock allows the user to designate which component  
will control the volume in the TV, DVD/LD and CBL/SAT  
modes. To set the Volume Lock to the TV mode:  
SETUP* - 992 - CBL/SAT - VCR - VCR -  
SETUP* - Cable/DBS code  
SETUP* - 992 - TV - DVD/LD - DVD/LD -  
SETUP* - TV code  
1.  
2.  
3.  
Press and hold SETUP until the Cinema 7’s red  
light blinks twice, then release SETUP.  
DVD/LD to VCR  
SETUP* - 992 - VCR - DVD/LD - DVD/LD  
Press 9 - 9 - 3. The Cinema 5’s red light will blink  
twice.  
- SETUP* - VCR code  
DVD/LD to RCVR  
DVD/LD to CBL/SAT  
RCVR to TV  
SETUP* - 992 - RCVR - DVD/LD -  
DVD/LD - SETUP* - Audio code  
Press and release TV. The Cinema 5’s red light  
will blink twice.  
SETUP* - 992 - CBL/SAT - DVD/LD -  
DVD/LD - SETUP* - Cable/DBS code  
Now, whenever you press VOL , VOL  
VCR, DVD/LD and CBL/SAT modes your TV will control the  
or MUTE in the  
SETUP* - 992 - TV - RCVR - RCVR -  
SETUP* - TV code  
 
volume. If you would like to change the Volume Lock setting to  
the VCR, DVD/LD or CBL/SAT modes repeat steps 1-3, only  
substitute the appropriate device key. Setting the Volume Lock  
to the TV, VCR, DVD/LD or CBL/SAT mode will not effect the  
volume control in the RCVR mode.  
3.  
To de-activate the built-in sleep timer,press  
POWER.  
NOTE: Plugging your TV into the outlet on the back of the  
Cable Converter may allow you to turn both your Cable  
Converter and TV ON and OFF  
You can also change the Volume Lock setting so that an  
Audio component controls the volume in all device modes.  
TROUBLE SHOOTING  
To change the Volume Lock setting on the Cinema 5 to the  
RCVR mode:  
Problem  
Solution  
1.  
2.  
3.  
Press and hold SETUP until the Cinema 5’s red  
light blinks twice, then release SETUP.  
Red light does not  
blink when you  
press a key?  
Replace the batteries with four (4) new AAA  
alkaline batteries.  
Press 9 - 9 - 3. The Cinema 5’s red light will blink  
twice.  
The Cinema 5  
Try all of the codes listed for your brand of  
home entertainment component in the “Setup  
Codes” section. Many setup codes may allow  
for partial functionality, however, only one  
setup code will operate your home entertain-  
ment component correctly. Make sure that all  
of the components you are setting up can  
be operated with an infrared remote con-  
trol.  
does not operate  
your home enter-  
tainment compo-  
nents or is not  
performing com-  
mands properly?  
Press and release RCVR . The Cinema 5’s red  
light will blink twice.  
Now, whenever you press VOL , VOL or MUTE your  
Audio component will control the volume in all device modes.  
You can also change the Volume Lock setting so that each  
component controls its own volume. However, some compo-  
nents do not have volume control. Using this setting may  
eliminate volume control in some device modes. To change  
the Volume Lock setting on the Cinema 5 so each mode  
controls its own volume:  
Problems pro-  
gramming a  
TV/VCR combo?  
Try the VCR set-up codes for your brand.  
However, some combo units may require both  
a TV code for volume control and a VCR code  
for the remaining functions.  
VCR not record-  
ing?  
As a safety feature on the Cinema 5, you  
must press the REC key twice.  
1.  
2.  
3.  
Press and hold SETUP until the Cinema 5’s red  
light blinks twice, then release SETUP.  
Press 9 - 9 - 3. The Cinema 5’s red light will blink  
twice.  
CH  
/
and  
Due to RCA design (1983-1987), only the  
original remote control will operate these  
functions.  
PREV CH not  
working for your  
RCA TV?  
Press and release VOL . The Cinema 5’s red  
light will blink twice.  
Problems chang-  
ing channels?  
If your original remote control required an  
Enter keystroke when changing channels,  
press the ENTER key on the Cinema 5 after  
you enter the channel number.  
Now, whenever you press press VOL , VOL or MUTE on  
the Cinema 5 each component will control its own volume,  
provided each component has volume control.  
The red light  
Make sure you are aiming your Cinema 5 at  
your home entertainment component and that  
you are within 15 feet before using your  
remote.  
blinks when you  
press a key but  
you receive no  
response from  
your home enter-  
tainment com-  
ponent?  
USING THE SLEEP KEY  
The SLEEP key allows you to access the sleep timer of your  
TV, Cable Converter/DBS Satellite or Audio component. You  
can access your TV, Cable Converter, DBS Satellite or Audio  
component’s Sleep Timer by pressing the SLEEP key. Most  
Sleep Timers advance in increments of 10 or 15 minutes,  
however, for specific instructions on setting your components  
Sleep Timer, please consult your original owner’s manual.  
Cinema 5 not  
learning a com-  
mand from your  
original remote  
control?  
Make sure your remote controls are nose-to-  
nose and are no more than 2 inches apart  
(see diagram in step 5 on page 24).  
Even if your original Cable Converter remote control did not  
have a sleep timer, your Cinema 5 has its own built-in sleep  
timer. If your Cable Converter does not have a sleep timer,  
press the SLEEP key to activate the Cinema 5’s built-in  
sleep timer. For example:  
Tried “Search  
Method” and still  
did not find the  
code?  
Try the “Search Method” again after clearing  
out the device key as follows: Press and hold  
SETUP until red light blinks twice, then  
release. Next enter 9 -9 - 2. Then press and  
release the device key to be cleared twice.  
1.  
Press and release the CBL/SAT key then press  
the SLEEP key once to set the Cinema 5’s built-in  
sleep timer for 15 minutes. The red light will blink  
once.  
2.  
Each additional press of the SLEEP key will add  
15 more minutes to the Sleep Timer, up to a maxi-  
mum of 60 minutes. The LED will blink twice when  
the sleep timer is set for 30 minutes, 3 times for  
45 minutes, or 4 times for 60 minutes.  
Sony’s Picture In  
Picture (PIP)  
won’t turn off?  
Press TV once. Press and hold SETUP until  
red light blinks twice, then release. Enter 9 - 9 -  
4 and press SETUP once. Then enter 6 -2 -1  
and press PIP On/Off. The red light should  
blink twice. PIP should operate properly now.  
Sharp’s Picture In  
Picture (PIP)  
won’t work prop-  
erly?  
Sharp’s PIP feature requires separate PIP  
functions for “on” and “off”.  
NOTE: The sleep timer starts 10 seconds after  
the last press of the SLEEP key. Once you have activated  
the Cinema 5’s built-in sleep timer, you must keep the  
remote control aimed directly at the component.  
 
®
ONE FOR ALL PRODUCTS  
For PIP “on”, press TV once. Press and hold  
SETUP until red light blinks twice, then  
release. Enter 9- 9-4 and press SETUP once.  
Enter 3- 4-8 and press PIP On/Off. The red  
light should blink twice. PIP “on” should oper-  
ate properly now.  
Limited Warranty  
One For All (“OFA”) warrants, to the original purchaser only, that  
this product will be free from defects in materials and workman-  
ship, under normal use, for ninety (90) days from the date of  
original purchase.  
For PIP “off”, press TV once. Press and hold  
SETUP until red light blinks twice, then  
release. Enter 9- 9-4 and press SETUP once.  
Enter 6-0-6 and press SETUP PIP On/Off.  
The red light should blink twice. PIP “off”  
should operate by pressing SETUP then the  
PIP key.  
This warranty does not cover damage or failures caused by  
products or services not supplied by OFA, or which result from  
accident, misuse, abuse, neglect, mishandling, misapplica-  
tion, faulty installation, set-up adjustment, improper mainte-  
nance, alteration, maladjustment of consumer controls, modi-  
fications, commercial use, or that is attributable to acts of God.  
There are no express warranties except as listed above. OFA  
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES RESULTING FROM THE USE OF  
THIS PRODUCT OR ARISING OUT OF ANY BREACH OF  
WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,  
INCLUDING THE WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMIT-  
ED TO THE WARRANTY PERIOD SET FORTH ABOVE.  
Some states do not allow the exclusion or limitation of inciden-  
tal or consequential damages, or limitations on how long an  
implied warranty lasts, so the above exclusions or limitations  
may not apply to you. This warranty gives you specific legal  
rights and you may also have other rights which vary from  
state to state.  
Surround on Sony  
receiver will not  
turn on?  
Press RCVR once. Press and hold SETUP  
until red light blinks twice, then release. Enter  
9- 9-4 and press SETUP once. Enter 3- 9-8  
and press SURROUND. Red light should blink  
twice. Surround should operate now.  
Sony receiver will  
turn off but not  
back on?  
Try using the number pad on the Cinema 5 to  
turn the receiver back on. For example, try  
pressing 0 to turn on in the CD mode, or 4 to  
turn on in the Video 1 mode. Other numeric  
keys will also turn the receiver on. If this does-  
n’t work, try the following:  
Press RCVR once. Press and hold SETUP  
until red light blinks twice, then release. Enter  
9- 9 -4 and press SETUP once. Then enter 5  
- 9 -1 and press POWER. The red light should  
blink twice. Power should operate properly  
now.  
To obtain warranty service for a defective product during the  
warranty period, please return the product, preferably in the  
original carton, along with your purchase receipt, to the store of  
original purchase. A note detailing the complaint would be help-  
ful. The store, at its option, will replace or repair this product if  
found to be defective.  
Audio component  
not fully-opera-  
tional?  
Audio functionality may be split between  
codes. For example, Pioneer’s Tuner code  
0014 works tuner presets, but only Amplifier  
code 0013 works power and volume. This also  
true for Sony’s Receiver code 0158 and Misc.  
Audio code 0159.  
One For All  
(330)-405-8655  
If some functionality is missing, try other  
codes to see if functionality resides there.  
Mini-system, book-  
shelf, or boombox  
not working?  
These systems may operate using a CD or  
Misc. Audio code. If the original remote con-  
trol did not have a power key, press PL (or  
STOP) to turn on (or off) the system.  
As you add new components to your home entertainment  
system, One For All has a remote control that will fit your  
needs. Look for these exciting products at a retailer near  
you.  
®
One For All and Cinema 5 are trademarks of Universal  
Electronics Inc.  
Consumer Help Line : 1-330-593-3335  
E-Mail Address : [email protected]  
ONE FOR ALL® is the registered trademark of Universal  
Electronics Inc. Computime International Ltd. is the  
Licensee of the ONE FOR ALL® brand for USA and  
Canada.  
One For All is designed for compatibility in North America  
excluding Mexico.  
URC-5800-Cinema 5  
12/00  
 

NETGEAR Switch GS510TP 100NAS User Manual
Netopia Network Router CLI 874 User Manual
Network Technologies Switch SM nXm C5AV LCD User Manual
Nokia Satellite TV System 1500S User Manual
NordicTrack Home Gym NTB09920 User Manual
NordicTrack Treadmill NTL10940 User Manual
Omron Healthcare Blood Pressure Monitor HEM 7211 E User Manual
Optoma Technology Projector EH500 User Manual
Panasonic Network Card 2SC4808G User Manual
Paradox Hellas SA Door DGP2 640 User Manual