Omega Thermometer HH501DK User Manual

OMEGA  
HH501DK  
Digital Thermometer  
 
INTRODUCTION  
This instrument is a portable 3½ digit, compact-sized digital thermometer  
designed to use external K-type thermocouple as temperature sensor. Tem-  
perature indication follows Reference Temperature/Voltage Tables (N.I.S.T.  
Monograph 175 Revised to ITS-90) for K-type thermocouples.  
SAFETY INFORMATION  
Itisrecommendedthatyoureadthesafetyandoperationinstructionsbefore  
using the thermometer.  
WARNING  
To avoid electrical shock, do not use this instrument when voltages  
at the measurement surface exceed 24V AC or DC.  
WARNING  
To avoid damage or burns, do not make temperature  
measurement in microwave ovens.  
CAUTION  
Repeated sharp flexing can break the thermocouple leads. To prolong  
lead life, avoid sharp bends in the leads, especially near the connector.  
The  
symbol on the instrument indicates that the operator must refer to an  
explanation in this manual.  
1
 
SPECIFICATIONS  
ELECTRICAL  
Temperature Scale: Celsius or Fahrenheit user-selectable  
Measurement Range: -50°C to 1300°C, (-58°F to 2000°F)  
Resolution: 1°C or 1°F, 0.1°C or 0.1°F  
Accuracy: Accuracy is specified for operating temperatures over the range of  
18°C to 28°C (64°F to 82°F), for 1 year, not including thermocouple error.  
±(0.3% rdg + 1°C) -50°C to 1000°C  
±(0.5% rdg + 1°C) 1000°C to 1300°C  
±(0.3% rdg + 2°F) -58°F to 2000°F  
Temperature Coefficient: 0.1 times the applicable accuracy specification  
per °C from 0°C to 18°C and 28°C to 50°C (32°F to 64°F and 82°F to 122°F).  
Input Protection: 24V dc or 24V ac rms maximum input voltage on any  
combination of input pins.  
Reading Rate: 2.5 times per second.  
Input Connector: Accepts standard miniature thermocouple connectors (flat  
blades spaced 7.9mm, center to center).  
2
 
ENVIRONMENTAL  
Ambient Operating Ranges: 0°C to 50°C (32°F to 122°F) <80% R.H.  
Storage Temperature: -20°C to 60°C (-4°F to 140°F) <70% R.H.  
GENERAL  
Display: 3½ digit liquid crystal display (LCD) with maximum reading of 1999.  
Battery: Standard 9V battery.  
Battery Life: 200 hours typical with carbon zinc battery.  
Dimensions: 192mm(H) x 91mm(W) x 52.5mm(D).  
Weight: 365g.  
3
 
OPERATING INSTRUCTIONS  
Selecting the Temperature Scale  
ReadingsaredisplayedineitherdegreesCelsius(°C)ordegreesFahrenheit(°F).  
To change the temperature scale, press the "°C" or "°F"key.  
Selecting the Display Resolution  
The thermometer allows two choices of resolution:  
High resolution: 0.1°C or 0.1°F  
Low resolution: 1.0°C or 1.0°F  
To select the alternate display resolution, press the corresponding "0.1°/1°"  
key.  
HOLD Mode  
Press " HOLD" button to toggle in and out of Hold mode, In the Hold mode, the  
" H " annunciator is displayed. (The Hold mode may be exited when changing  
function.)  
Display Back-Light  
Pressing the " " key to toggle turn on or turn off the Back-Light.  
4
 
MAX Mode  
Pressing the Max key to enter the MAX mode. The thermometer then records  
andupdatesthemaximumabsolutevaluesandtheMAXannunciatorappears  
on the display. Pressing the MAX key again to exit the MAX recording mode.  
In the MAX mode, press HOLD key to stop the recording, press HOLD again  
to resume recording.  
T1,T2,T3,T4, T1-T2,T1-T3,T1-T4 Temperature Measurement  
1. The function switch indicates which input is selected for display; T1  
thermocouple, T2 thermocouple,T3 thermocoupleor, T4 thermocouple or  
the difference between the two thermocouples (T1-T2, T1-T3, T1-T4).  
2. Connect a type k thermocouple to the jack on the instrument. Place the  
probe or thermocouple tip on or in the material to be measured and take the  
temperature reading directly from the display.  
5
 
MAINTENANCE  
WARNING  
To avoid possible electrical shock, disconnect the thermocouple  
connectors from the thermometer before removing the cover.  
Battery Replacement  
Power is supplied by a 9 volt "transistor" battery. (NEDA 1604, IEC 6F22). The  
"
"appearsontheLCDdisplaywhenreplacementisneeded. Toreplacethe  
battery, remove the two screws from the back of the meter and lift off the  
battery cover. Remove the battery from battery contacts.  
6
 
HH501DK CALIBRATION PROCEDURE  
Note: The following calibration procedure should perform only by qualified technicians  
who have access to the items as following.  
Equipment: The class of calibrator had better 10 times greater than the measured meter.  
Temperature Calibration  
Insert the K type thermocouple to the female connector, and the other side of this  
probe to Temperature Calibrator and connect output to the voltage meter. We  
must allow the K type to stabilize for at least 1 minute and make sure “+” and “-“  
polarity is right position.  
1. Set the range to the T1/0.1°C, and then apply 0°C to T1 input (T2 input open)  
adjust R3 and R4 (fine adj.) until LCD reading reads 0.0±0.1°C.  
2. Set the range to the T2/0.1°C, and then Apply 0°C to T2 input (T1 input open)  
adjust R1 and R2 (fine adj.) until LCD reading reads 0.0±0.1°C.  
3. Set the range to the T1/0.1°F, and then apply 0°F to T1 input (T2 input open)  
adjust R6 until LCD reading reads 0.0±0.1°F.  
4. Set the range to the T1/0.1°F, and then apply 165°F to T1 input (T2 input  
open) adjust R7 until LCD reading reads 165.0±0.1°F.  
5. Set the range to the T1/1°F, and then apply 1832°F to T1 input (T2 input  
open) adjust R5 until LCD reading reads 1832±1°F.  
6. Set the range to the T1/1°C, and then apply 1000°C to T1 input (T2 input  
open) adjust R8 until LCD reading reads 1000±0°C.  
 
1
WARRANTY / DISCLAIMER  
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months  
from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product  
warranty to cover handling and shipping time.This ensures that OMEGA's customers receive maximum coverage on each product.If  
the unit should malfunction, it must be returned to the factory for evaluation. OMEGA's Customer Service Department will issue an  
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to  
be defective it will be repaired or replaced at no charge. OMEGA's WARRANTY does not apply to defects resulting from any action  
of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair,  
or unauthorized modification.This WARRANTY isVOID if the unit shows evidence of having been tampered with or shows evidence  
of being damaged as a result of excessive corrosion; or current, heat moisture or vibration; improper specification; misapplication;  
misuse or other operating conditions outside of OMEGA's control. Components which wear are not warranted, including but not  
limited to contact points, fuses, and triacs.  
OMEGA is pleased to offer suggestions on the use of its various products.However,OMEGA neither assumes responsibility  
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance  
with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it  
will be as specified and free of defects. OMEGA MAKES NO OTHERWARRANTIES OR REPRESENTATIONS OF ANY KIND  
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY  
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.  
LIMITATION OF LIABILITY:The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with  
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall  
not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for  
consequential, incidental or special damages.  
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a "Basic Component" under 10  
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any  
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,  
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and additionally, purchaser will  
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in  
such a manner.  
RETURN REQUESTS / INQUIRIES  
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY  
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S  
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then  
be marked on the outside of the return package and on any correspondence.  
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.  
FOR WARRANTY RETURNS, please have the following  
information available BEFORE contacting OMEGA:  
1. P.O. number under which the product was PURCHASED.  
FOR NON-WARRANTY REPAIRS, consult OMEGA for  
current repair charges. Have the following information  
available BEFORE contacting OMEGA:  
2. Model and serial number of the product under warranty, and 1. P.O. number to cover the COST of the repair.  
3. Repair instructions and/or specific problems relative to the  
product.  
2. Model and serial number of product , and  
3. Repair instructions and/or specific problems relative to the  
product.  
OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest  
in technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 1999 OMEGA ENGINEERING,  
INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or  
machine-readable from, in whole or in part, without prior written consent of OMEGA ENGINEERING, INC.  
 
Whe re Do I Find Eve rything I Ne e d for  
Proc e ss Me a sure m e nt a nd Control?  
OMEGA...Of Course !  
TEMPERATURE  
DATA ACQUISITION  
þ Data Acquisition &  
Engineering Software  
þ Communications-Based  
Acquisition Systems  
þ Plug-in Cards for Apple, IBM  
& Compatibles  
þ Thermocouple, RTD & Thermistor  
Probes, Connectors, Panels & Assemblies  
þ Wire: Thermocouple, RTD & Thermistor  
þ Calibrators & Ice Point References  
þ Recorders, Controllers & Process Monitors  
þ Infrared Pyrometers  
þ Datalogging Systems  
þ Recorders, Printers & Plotters  
PRESSURE/ STRAIN AND FORCE  
þ Transducers & Strain Gauges  
þ Load Cells & Pressure Gauges  
þ Displacement Transducers  
HEATERS  
þ Heating Cable  
þ Instrumentation & Accessories  
þ Cartridge & Strip Heaters  
þ Immersion & Band Heaters  
þ Flexible Heaters  
FLOW/ LEVEL  
þ Rotameters, Gas Mass Flowmeters  
& Flow Computers  
þ Laboratory Heaters  
ENVIRONMENTAL  
þ Air Velocity Indicators  
þ Turbine/Paddlewheel Systems  
þ Totalizers & Batch Controllers  
MONITORING AND CONTROL  
þ Metering & Control Instrumentation  
þ Refractometers  
p H/ CONDUCTIVITY  
þ Pumps & Tubing  
þ pH Electrodes, Testers & Accessories  
þ Benchtop/Laboratory Meters  
þ Controllers, Calibrators, Simulators  
& Pumps  
þ Air, Soil & Water Monitors  
þ Industrial Water & Wastewater  
Treatment  
þ pH, Conductivity & Dissolved Oxygen  
Instruments  
þ Industrial pH & Conductivity Equipment  
M-2985/0799  
 

MTD Trimmer BT1045 1 User Manual
Multi Tech Systems Network Router MT9234ZBA User Manual
Nokia Bluetooth Headset BH 904 User Manual
Nokia Network Router CC100 User Manual
NuTone Ventilation Hood 770F User Manual
Oregon Edger Edger User Manual
Orion Car Audio Car Amplifier 300 PSW User Manual
Panamax Power Supply MAX 5510 User Manual
Panasonic CD Player CT 27G12 User Manual
Panasonic VCR AJ D455P User Manual