OTC Wireless Car Video System ASR 102 G User Manual

cable to a hub or switch. Check that the  
orange LED labeled “LINK” is solid or  
blinking regularly. If the LED stays off, use  
the (white) straight-thru cable instead.  
browser (e.g. Internet Explorer) to confirm  
a wireless connection to the Internet. If  
the ASR-102-G is connected to a local  
network, use a network application, e.g.  
Network Neighborhood, to confirm wireless  
connection.  
When properly connected and powered on,  
the four LED’s on top of the radio should  
exhibit the following patterns:  
D. The most likely cause for failed  
connections is that the station and Access  
Point radios have mismatched SSID, WEP  
encryption, and/or security settings.  
Configure these settings appropriately.  
LED Indicator  
Radio ON  
ON  
TX  
On (red)  
Blink (red)  
Included with the ASR-102-G  
ASR-102-G AP Radio  
RX  
Link  
On (green)  
On/ Blink (orange)  
5V DC Adapter and Power cord  
USB Power Cord  
IMPORTANT: Save your configuration to  
template right after making any changes,  
especially for password changes.  
White Straight-through UTP Cat5 Cable  
Blue Crossover UTP Cat5 Cable  
Technical Manual on CD  
Sticky Velcro Mounting Pad Pair  
Radio Clip  
2. Check Radio Configuration and  
Wireless Connection ..  
A. The ASR-102-G is pre-configured with  
default parameters to allow you to instantly  
establish a wireless link with an ACR-201  
Radio unit or any 802.11b/g station radios.  
For technical assistance, please call OTC  
Wireless at 1-800-770-6698 (Inside USA) or  
011-510-490-8288 (Outside USA) or visit  
1. Connecting the ASR-102-G  
A. Connect the 5V DC adapter or USB  
Power Cord to the DC input on the bottom  
of the ASR-102-G unit. Connect the USB  
Power Cord to any USB port or DC adapter  
to proper wall outlet to power the ASR-  
102-G unit.  
B. To modify any of the radio operating  
parameters, connect your ASR-102-G radio  
to a PC. Open a Web browser on your PC  
to http://169.254.98.201 to access the  
web-based utility. When the log-in window  
appears, enter “admin” as the user name  
and “public” as the password. Configure  
your radio as appropriate.  
B. For wireless Internet connections,  
connect the ASR-102-G with the (white)  
straight-through Cat5 cable to a DSL  
modem, cable modem, or router. Check  
that the orange LED labeled “LINK” is solid  
or blinking regularly. If the LED stays off,  
use the (blue) crossover Cat5 cable  
instead.  
Note: The computer must be in the same  
subnet as the radio. For example, set your  
PC with the IP address of 169.254.98.100.  
C. To check for a wireless connection,  
connect the ASR-102-G to a router and  
connect an ACR-201-G or any other  
802.11b/g station radio to a PC. Use a web  
C. For local wireless networking, connect  
the ASR-102-G with the (blue) crossover  
ASR-102-G Quick Start Guide v 1.0  
 

Miele Vacuum Cleaner S157 User Manual
Miller Electric Welder LMSW Series User Manual
Multi Tech Systems Modem MTSMC EV3 User Manual
NEC Telephone R1000 User Manual
NETGEAR Network Router EDA 500 User Manual
Nintendo Video Games 61313A User Manual
Nokia Cell Phone PM 3205 User Manual
Onkyo Stereo Receiver TX SR403 User Manual
Oster Toaster 6240 User Manual
Panasonic Electric Shaver ESLV61 User Manual