NuTone Fan PFLK 123 User Manual

INSTALLATION INSTRUCTIONS  
READ & SAVE THESE INSTRUCTIONS!  
Ceiling Fan Light Kits  
Models: PFLK-123 Series  
IMPORTANT: These Ceiling Fan Light Kits are for use with  
NuTone Model PFOB-52 only.  
CAUTION  
SWITCH  
HOUSING  
1. CAUTION - To reduce the risk of fire and electrical shock,  
this light kit should be used only with NuTone fan model  
PFOB-52.  
2. Read entire instructions carefully before beginning installation.  
PIPE, NIPPLE,  
NUTS, ETC.  
COVER PLATE  
3. CAUTION - To reduce the risk of electrical shock, disconnect  
the electrical supply circuit to the fan before installing the light  
kit.  
4. All wiring must be in accordance with national and local  
electrical codes. If you are unfamiliar with wiring, you should  
use a qualified electrician.  
FIGURE 1  
MAKING THE CONNECTIONS  
NOTE: See fan instructions for connecting house wiring to the  
fan. Connect house wiring to the fan before attaching light kit to  
the fan. See wiring diagrams on back of this page, titled wiring  
wall switches.  
FAN AND LIGHT ON A SINGLE WALL SWITCH  
WHITE  
WIRE  
WHITE WIRE  
115 VOLT SUPPLY  
BLACK WIRE  
WITH TRACER  
OR BLUE WIRE  
1. Refer to Figures 1. Remove the cover plate from the bottom  
of the fan switch housing.  
BLACK WIRE  
2. Assemble the cover plate to the light kit as shown. Use the  
pipe nipple and nuts provided.  
MOTOR  
CONNECTIONS  
(NON-ACCESSIBLE)  
3. Locate the two wires in the fan switch housing that have  
labels marked “Connect Light Here” or “For Light Use”.  
One wire will be white and the second will be black or blue  
with or without white tracer. Connect these wires to the wires  
coming from the light kit. Assemble the light kit to  
the fan using the screws removed in step 1 (one) above.  
Re-assemble bottom cover and pendent to the fan. Proceed  
to completing the Installation.  
CEILING  
FAN  
BLACK WIRE  
WITH TRACER  
OR BLUE WIRE  
WHITE  
WIRES  
WALL  
SWITCH  
BLACK  
WIRE  
LIGHT KIT  
FIGURE 2  
COMPLETING THE INSTALLATION  
1. Install (1) 100 watt maximum light bulb. Note: Refer to the  
guide for maximum size bulb that is printed on the  
light fixture.  
FAN AND LIGHT ON SEPARATE WALL SWITCHES  
WHITE  
WIRE  
2. Should light shade begin to buzz, be certain all  
thumbscrews are tight.  
WHITE WIRE  
115 VOLT SUPPLY  
BLACK WIRE  
WITH TRACER  
OR BLUE WIRE  
WIRING WITH WALL SWITCHES  
The Ceiling Fan and Light Kit can be connected  
through wall switches. This can be done in two ways.  
Select the type of control desired and wire the unit  
according to Figure 2 or Figure 3.  
BLACK WIRE  
MOTOR  
CONNECTIONS  
(NON-ACCESSIBLE)  
Use one wall switch to control both fan and light.  
Individual control of either fan or light is done with the  
pull chain switches.Or use two wall switches to  
individually control both fan and light – one for the fan  
and the second for the light. Pull chain switches on  
the fan do not have to be used.  
CEILING  
FAN  
BLACK WIRE  
WITH TRACER  
OR BLUE WIRE  
WHITE  
WIRES  
WALL  
WALL  
SWITCH  
FOR  
BLACK  
WIRE  
SWITCH  
FOR FAN  
LIGHT KIT  
LIGHTS  
FIGURE 3  
 

Multiquip Portable Generator DCA 10SPX4 User Manual
Napco Security Technologies Home Security System F 64TPBR User Manual
Netopia Network Card 6161210 00 01 User Manual
New Holland Lawn Mower CR9000 Series User Manual
Nikon Digital Camera 26460 User Manual
Olympus Camera Accessories FS HV1 User Manual
Panasonic Air Conditioner CW C200NU User Manual
Panasonic Telephone KX T7130 User Manual
Panasonic Webcam HDC HS80 User Manual
Paradyne Network Router 6302 User Manual