Nortel Networks Telephone 03050 User Manual

Registering individual portables  
Registering the C3060  
The following section describes the procedures involved in  
registering Companion C3060 portable telephones. To register  
each portable with the Norstar system, you must do two things:  
Register the portables by entering the Registration  
password on each one.  
Verify that the portable functions correctly.  
C3060 Icons  
The following table identifies the C3060 portable telephone  
icons:  
C3060  
Icon function  
Mute button  
Hang up button  
Answer button  
Feature button  
k
i
m
Telephone directory button  
Service directory button  
l
j
To register the C3060  
1. Turn on registration for your system.  
2. Press m***. The display shows ADMINISTRATION  
and three softkeys, SYS, PINFO, DATA.  
3. Press SYS. The display shows WIRELESS SYSTEMS.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
Registering individual portables / 91  
Press the dial pad key until the letter you need appears on  
the display. For example, press key 5 three times to display  
the letter L.  
Press SPACE to add a blank space to the name.  
Press BKSP to delete the previous character.  
Press >if the next letter is on the same button.  
8. Press SAVE . The display shows the registered name. For  
example, NORTEL 1 registered .  
9. Turn off registration for your system.  
To confirm that the C3060 is registered  
1. Select the system you just registered.  
a. Press kto power off the portable, and press k  
again to power on the portable.  
If the display shows the system name that you just  
registered, proceed to step 2.  
If the display shows a different system name or No system  
selected, continue with the next step, sub-step b.  
b. Press m*** .  
c. Press SYS.  
d. Press , or . until the display shows the system  
name you just registered.  
e. Press SELCT. Then press OK or END to exit  
Administration.  
2. Make a call.  
a. Press i. You hear dial tone, and the display shows  
LINK. If you do not hear dial tone, check that you have  
selected the correct system or register the portable  
again.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
92 / Registering individual portables  
b. Dial the number of a working telephone. The telephone  
must ring to confirm the registration.  
3. Receive a call.  
a. If the portable has the same extension number as a desk  
telephone, make sure the desk telephone is idle and Call  
Forward is not active.  
b. On another working telephone, dial the telephone  
number of the registered portable. The portable must  
ring to confirm the registration.  
If you do not hear dial tone, or if the portable does not ring,  
refer to “Troubleshooting” in Meridian Companion  
Installation and Maintenance Guide. If you continue to  
experience difficulty registering the portable, contact your  
distributor.  
Deregistering the C3060  
You can deregister the C3060 in several ways:  
from the portable  
from the Administration Terminal (refer to Meridian  
Companion Administration Terminal Operations Guide)  
from Companion Manager (refer to Companion Manager  
Installation and Operations Guide)  
Deregistering the C3060 from the portable clears registration  
information stored in the portable and the system. For  
example, you may want to deregister the portable before you  
assign it to another WTN on the same system.  
Deregistering the C3060 from the Administration Terminal or  
from Companion Manager does not clear registration data  
from the portable. (You could use this method if the portable  
were lost or stolen or if you wanted to assign it to another  
system.)  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 93  
If a portable is registered on other systems, it will still be  
available on those systems. You deregister one system at a  
time.  
Note: If you are out of range of the system, this procedure  
clears registration data only from the portable.  
1. Press m***. The display shows ADMINISTRATION  
and three softkeys, SYS, PINFO, DATA.  
2. Press SYS. The display shows WIRELESS SYSTEMS.  
3. Press ERASE . The display shows Erase item? .  
4. Press OK . The display shows Deregistering... and then  
Item erased.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
94 / Registering individual portables  
Measuring RSSI for a C3060  
The Receive Signal Strength Indicator (RSSI) is a  
measurement of the signal strength the Base Station receives  
from the portable. The Base Station controls the power  
transmitting mode of the portable. When the Base Station  
receives a weak signal, it instructs the portable to transmit in  
high-power. When the Base Station receives a strong signal, it  
instructs the portable to transmit in low-power. The strongest  
RSSI value the display shows is -35 dBm. The weakest RSSI  
value the display shows is approximately -94 to -100 dBm.  
Measuring undirected RSSI  
You can measure the signal strength between a portable and a  
system-selected Base Station using undirected RSSI.  
1. Press m. The display shows MENU.  
2. Press ,or.until the display shows Feature request  
.
3. Press SELCT . The display shows A- .  
4. Press * 8 9 8. The display shows the cell  
number, the radio ID of the Base Station to which the  
portable is linked, the power mode (high or low), followed  
by the signal strength and the channel. For example, 8  
15112 H 67 29.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
 
Registering individual portables / 95  
You can also press to view the information in “standard”  
display mode. This mode displays the radio ID of the Base  
Station to which the portable is linked, followed by the  
signal strength and power mode. For example, 15112 - 67  
H . You can revert back to the initial display mode by  
pressing .  
Hand-off occurs normally between the cells.  
Note: In this example, the cell is 8, the card is 15, the port is  
11, the radio is 2, and the channel is 29. The signal  
strength measured by the Base Station is -67 dBm, and  
the H indicates the portable is transmitting in high-  
power mode (an L indicates low-power mode).  
5. To end the connection, press k.  
Measuring directed RSSI  
You may want to measure the RSSI between a portable and a  
specific Base Station radio. For example, you may suspect that  
one of the two radios in a Base Station is not working properly.  
You can also use directed RSSI to prevent hand-off while you  
find a cell edge. To measure the RSSI of a specific radio, you  
must be in range of two Base Stations—the one you want to  
measure and another Base Station.  
Note: You cannot measure the directed RSSI of both radios in  
the Base Station at the same time.  
Before you measure directed RSSI, use Meridian Companion  
Programming and Provisioning Record to find and note the  
following:  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
96 / Registering individual portables  
The five-digit ID of the Base Station radio you want to  
measure, by mapping the Base Station location to the TCM  
port. The first four digits indicate the TCM port to which  
the Base Station is connected. The last digit indicates the  
number of the radio on the Base Station. For example, the  
number 03142 on the Base Station is connected to TCM  
port 0314, and 2 is the radio number. The five-digit  
number might be printed on a label attached to the Base  
Station mounting bracket.  
The radio IDs of all other Base Stations in the same  
location.  
1. Follow steps 1 to 5 of “Measuring undirected RSSI’’ on  
page 94.  
If the display shows the ID of a Base Station neighboring  
the one you want to measure, proceed to step 2.  
If the display shows the ID of the Base Station you want to  
measure, move out of the cell boundary range so that hand-  
off occurs and then continue with step 2.  
2. Press m. The display shows MENU.  
3. Press ,or .until the display shows Feature  
request.  
4. Press SELCT . The display shows A- .  
5. Press * 8 9 9.  
6. Enter the five-digit ID code for the Base Station radio you  
want to measure. The display shows the cell number, the  
radio ID of the Base Station to which the portable is linked,  
the power mode (high or low), followed by the signal  
strength and the channel. For example,  
8 15112 H 67 29.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 97  
You can also press to view the information in “standard”  
display mode. This mode displays the radio ID of the Base  
Station to which the portable is linked, followed by the  
signal strength and power mode. For example, 15112 - 67  
H . You can revert back to the initial display mode by  
pressing .  
Hand-off does not occur as you move between the cell  
boundaries. The link drops when you move out of range.  
Note: In this example, the cell is 8, the card is 15, the port is  
11, the radio is 2, and the channel is 29. The signal  
strength measured by the Base Station is -67 dBm, and  
the H indicates the portable is transmitting in high-  
power mode (an L indicates low-power mode).  
7. To end the connection, press m.  
Registering the C3050  
The following section describes the procedures involved in  
registering Companion C3050 portable telephones. To register  
each portable with the Norstar system, you must do two things:  
Register the portables by entering the Registration  
password on each one.  
Verify that the portable functions correctly.  
C3050 Icons  
Some C3050 portable telephone icons for Canada and the  
United States are different but have the same functions. The  
following table identifies these icons:  
C3050 Canada  
Icon function  
Mute button  
Hang up button  
C3050 US  
µ
´
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
98 / Registering individual portables  
C3050 Canada  
Icon function  
Answer button  
C3050 US  
Ò
Feature button  
Ï
Î
Telephone directory button  
To register the C3050  
1. Turn on registration for your system.  
2. Open the portable flap. The portable displays the current  
system name or No system selected for two seconds.  
3. Press Í. The portable displays WIRELESS SYSTEMS.  
Your portable can be registered to a maximum of nine  
different systems.  
4. Press the ADD key to establish a radio link. The portable  
displays Adding SYSTEM:# for two seconds, then it  
displays Pswd:.  
If a radio link is not established, the portable displays  
No connection. Close the flap, and repeat the procedure  
from step 1.  
5. Enter the Registration password. The default is  
¶™£¢§(RADIO). The portable displays  
DN:.  
If the registration password is not correct, the portable  
displays InvldPswd. Close the flap and repeat the  
procedure from step 1.  
6. Enter the DN (between 637 and 666). The portable  
displays Enter name.  
If the DN is incorrect, the portable displays Invld DN. If  
the registration fails, the portable displays Reg failed.  
If you try to register the C3050 to the same system twice,  
the portable displays the registered name, for example  
Registered as NORTEL 1.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 99  
7. Enter the system name (up to 16 characters), for example  
NORTEL 1. (If you are registering to only one system, use  
the portable telephone user’s name.)  
Press the key that has the letter. For example, to enter A,  
press , to enter B, press ™™.  
Press SPACE to add a blank space to the name.  
Press BKSP to remove a mistake.  
Press ¯or ˘to move the cursor backward or forward.  
8. Press SAVE. The portable displays the registered name, for  
example NORTEL 1 registered.  
9. Turn off registration for your system.  
To confirm that the C3050 is registered  
1. Close, then open the portable flap.  
If the portable displays the system name that you just  
registered, proceed to step 5.  
If the portable displays a different system name, or No  
system selected, proceed to step 2.  
2. Press Í. The portable displays WIRELESS SYSTEMS.  
3. Press the scroll keys (or ) until the system name  
is displayed.  
4. Press SELCT (or OK if the correct system is already  
selected).  
5. Press Òor . You hear a dial tone, and the portable  
displays [.  
If you do not hear a dial tone, check that you have selected  
the correct system and try to register the portable again.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
100 / Registering individual portables  
6. Close the portable’s flap, and set the Ringer Control  
Switch to g.  
If the portable is twinned with a desk telephone, make sure  
the desk telephone is idle and Call Forward is not active.  
7. On another working telephone, dial the telephone number  
of the registered portable. If the portable rings, it is  
functioning properly.  
If you do not hear a dial tone, or if the portable does not ring,  
refer to the Troubleshooting section in this guide. If you still  
cannot register the portable, contact your system supplier.  
Deregistering the C3050  
You can deregister the C3050 in two ways:  
from the portable  
from the administration set  
You can deregister the portable to clear information stored in  
the portable and the system. To do this, you must be within the  
coverage area. For example, you may want to deregister the  
portable before you assign it to another DN.  
You can also deregister a portable using the Norstar  
administration set. You could use this method if the portable  
was lost or stolen, or if you wanted to assign it to another  
system. This procedure does not clear registration data from  
the portable.  
If the portable is registered on other systems, it is still available  
on those systems. You deregister from one system at a time.  
To deregister the C3050  
1. Open the portable’s flap.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 101  
2. Press Í. The portable displays WIRELESS SYSTEMS and  
ADD.  
Note: Do not select ADD.  
3. Press the scroll keys (or ) to display the system  
name that you want to deregister.  
4. Press ERASE. The portable displays Erase item?.  
5. Press OK. The portable displays Deregistering... and  
then Item erased.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
102 / Registering individual portables  
Measuring RSSI for a C3050  
The Receive Signal Strength Indicator (RSSI) is a  
measurement of the signal strength the Base Station receives  
from the portable. The Base Station controls the power  
transmitting mode of the portable. When the Base Station  
receives a weak signal, it instructs the portable to transmit in  
high-power. When the Base Station receives a strong signal, it  
instructs the portable to transmit in low-power. The strongest  
RSSI value the portable displays is -45 dBm (in the US) and  
-44 dBm (in Canada). The weakest RSSI value the portable  
displays is approximately -94 to -100 dBm.  
To measure undirected RSSI  
You can measure the signal strength between a portable and a  
system-selected Base Station radio using undirected RSSI.  
1. Open the portable flap.  
2. Press Òor .  
3. Press °•ª•. The portable displays the radio  
ID of the Base Station that the portable is linked to,  
followed by the signal strength and the power mode, for  
example 03142 - 54 H. Hand-off occurs normally  
between the cell boundaries.  
In this example, the module is 03, the port is 14, and the  
radio is 2. The signal strength measured by the Base  
Station is -54 dBm, and the H indicates that the portable is  
transmitting in high-power mode (an L indicates low-  
power mode).  
4. To end the connection, press ´or or close the flap.  
Measuring directed RSSI  
You may want to measure the RSSI between a portable and a  
specific Base Station radio. For example, you may suspect that  
one of the two radios in a Base Station is not working properly.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
 
Registering individual portables / 103  
You can also use directed RSSI to prevent hand-off while you  
find a cell edge. To measure the RSSI of a specific radio, you  
must be in range of two Base Stations—the one you want to  
measure and another Base Station.  
You cannot measure the directed RSSI of both radios in the  
Base Station at the same time.  
Before you begin to measure directed RSSI  
Use the Companion Provisioning Record to find the  
following:  
the five-digit ID of the Base Station radio you want to  
measure, by mapping the Base Station location to the time  
compression multiplex (TCM) port. The first four digits  
indicate the TCM port to which the Base Station is  
connected. The last digit indicates the number of the radio  
on the Base Station. For example, the number 03142 on  
the Base Station is connected to TCM port 0314, and 2 is  
the radio number. The five-digit number may be printed on  
a label affixed to the lower right corner of the Base Station  
mounting bracket.  
the radio IDs of all other Base Stations in the same  
location.  
To measure directed RSSI using your portable  
1. Repeat steps 1 to 3 of “To measure undirected RSSI’’ on  
page 102.  
2. When the portable displays the Base Station ID you want  
to measure, move out of the cell boundary range so that  
hand-off occurs, and press ´ or .  
3. Press Òor .  
4. Press °•ªª.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
104 / Registering individual portables  
5. Enter the five-digit ID code for the Base Station radio you  
want to measure. The portable displays this ID followed by  
the signal strength and the power mode, for example  
03142 - 54 H. Hand-off does not occur as you move  
between the cell boundaries. The link drops when you  
move out of range.  
In this example, the module is 03, the port is 14, and the  
radio is 2. The signal strength measured by the Base  
Station is -54 dBm, and the H indicates the portable is  
transmitting in high-power mode (an L indicates low-  
power mode).  
6. To end the connection, press ´, or close the flap.  
Registering the C3020 (Canada only)  
The following section describes the procedures involved in  
registering Companion C3020 portable telephones. To register  
each portable with the Norstar system, you must do two things:  
Register the portables by entering the Registration  
password on each one.  
Verify that the portable functions properly.  
To register the C3020  
1. On the Administration set, turn on registration in a general  
programming session.  
2. On the portable, press s, then press m.  
2. Press o.  
3. Check the portable’s display.  
If the portable has space for another system, the display  
shows Office n: Free.  
If the display does not show Office n: Free., follow the  
procedures in “Deregistering the C3020 (Canada only)’’  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 105  
on page 106 to overwrite the system number then return to  
step 2 of this procedure.  
4. Press s, then press m. The display shows  
Registering....  
5. Next, enter the Registration password when the display  
shows Pswd:. The default is 7 2 3 4  
6 (RADIO).  
If the display does not clear after entering the password,  
then you may be using the wrong password.  
6. Wait for the display to clear. When it shows DN:, enter the  
internal number (637-666) you want to assign to the  
portable. When the display clears, it shows  
Reg'n complete.  
7. On the administration set, turn off registration in general  
programming, Companion, subheading Registration.  
To confirm that the C3020 is registered  
1. To check that the portable has a dial tone, press L.  
If you do not hear a dial tone, check that you have selected  
the correct system number and press Lagain. If you no  
not hear dial tone try to register the portable again.  
2. Make sure that the flap is closed and the Ringer Control  
Switch is in the bottom position. Make sure the portable  
telephone is idle and call forward is not active.  
3. On a working telephone, dial the telephone number of the  
registered portable.  
If the portable rings, it is functioning properly.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
106 / Registering individual portables  
If the portable does not ring, try to register the portable  
again.  
If you do not hear a dial tone, or if the portable does not  
ring, refer to the Troubleshooting section in this guide.  
Deregistering the C3020 (Canada only)  
You can deregister the C3020 in two steps:  
from the portable  
from the administration set (For more information about  
using the Norstar administration set, see the Modular ICS  
System Coordinator Guide.)  
For example, you may want to deregister the portable before  
you assign it another number on the same system.  
You can also deregister a portable using the administration set.  
You could use this method if the portable was lost or stolen or  
if you wanted to assign it to another system. This procedure  
does not clear registration data from the portable.  
If the portable is registered on other systems, it is still available  
on those systems. You deregister one system at a time.  
To deregister the C3020  
1. Press s, then press m.  
2. Press o. The display shows Office n:.  
3. Press either s then #, or s then * until  
you display the system you want to deregister.  
4. Press s, then press 0. The display shows  
Deregister?.  
5. Press s, then press 0 again. The display shows  
Deregistering... and then Deregistered.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
 
Registering individual portables / 107  
6. To continue using the portable, press r.  
Measuring RSSI for a C3020 (Canada only)  
The Receive Signal Strength Indicator (RSSI) is a  
measurement of the signal strength the Base Station receives  
from the portable. The Base Station controls the power  
transmitting mode of the portable. When the Base Station  
receives a weak signal, it instructs the portable to transmit in  
high-power. When the Base Station receives a strong signal, it  
instructs the portable to transmit in low-power. The strongest  
RSSI value the portable displays is -44 dBm. The weakest  
RSSI value the portable displays is approximately -85 to -95  
dBm.  
Receive Signal Strength Indicator overrides  
normal display.  
You cannot receive calls while measuring  
Receive Signal Strength Indicator.  
Measuring undirected RSSI  
You may want to measure the Receive Signal Strength  
Indicator between a portable and a Base Station radio.  
1. Press L. Wait for dial tone.  
2. Press *. Enter the feature code: 8 9 8.  
The display shows the radio ID of the Base Station to  
which the portable is linked, followed by the signal  
strength, for example 03121 - 67. In this example, the  
module is “03,” the port is “12,” and the radio is “1.” The  
signal strength is “-67dBm.”  
3. Read your measurement. Hand-off occurs normally.  
4. To end the connection, press ror close the flap.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
108 / Registering individual portables  
Measuring directed RSSI  
You may want to measure the Receive Signal Strength  
Indicator between a portable and a specific Base Station radio.  
For example, you may suspect that a radio in a Base Station is  
not working properly. You can also use directed Receive  
Signal Strength Indicator to prevent hand-off while you find a  
cell edge. To measure the Receive Signal Strength Indicator of  
a desired radio, you must be in range of two Base Stations—  
the one you want to measure, and another Base Station.  
Receive Signal Strength Indicator applies to  
one radio in a Base Station.  
You cannot measure the directed Receive Signal  
Strength Indicator of the other radio in the Base  
Station to which you are connected.  
Before you begin measuring directed RSSI  
Use the Companion Provisioning Record to find and note the  
following:  
the five-digit radio ID of the Base Station you want to  
measure, by mapping the Base Station location to the TCM  
port. The first four digits indicate the TCM port to which  
the Base Station is connected. The last digit indicates the  
number of the radio on the Base Station. For example, the  
number “03122” identifies radio “2” on the Base Station  
connected to TCM port “0312”.  
the radio IDs of all other Base Stations in the same  
location.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 
Registering individual portables / 109  
Measuring directed RSSI using your portable  
1. Perform an undirected Receive Signal Strength Indicator  
by following steps 1 to 3 in “To measure undirected RSSI’’  
on page 102. To direct the Receive Signal Strength  
Indicator to the other radio of the Base Station, move out  
of range until hand-off occurs before moving on to step 2.  
2. Press L. Wait for dial tone.  
3. Press * 8 9 9.  
4. Enter the five-digit ID code for the Base Station radio you  
want to measure. The display shows this ID followed by  
the signal strength, for example 03121 - 67. If you have  
not established a connection with the desired Base Station  
radio, you hear a tone when you hold the portable to your  
ear.  
5. Read your measurement. The system drops the link when  
you move out of range of your Base Station (no hand-off).  
6. To end the connection, press r, or close the flap.  
After registering the portables  
When you have completed programming the system, use the  
following checklist to ensure you completed the required  
tasks.  
å
å
å
å
å
å
Register the portables.  
Verify Portable Credits.  
Ensure that you registered all the required portables.  
Verify that all portables are available for use.  
Test each portable to verify it is operating properly.  
Disable Master Registration when you have finished  
registering the portables.  
P0881594 Issue 02  
MICS-XC Norstar-Companion Installer Guide  
 
110 / Registering individual portables  
For the steps involved in operating a Norstar Companion  
portable, see the Companion Portable Telephone User Guide  
that is supplied with the portable.  
When you distribute the portables, tell the users that the  
portables are registered and give them the corresponding  
extension numbers.  
Tip - You can register a portable to more than one  
system. You cannot register a portable to more than one  
extension number per system. You cannot register more  
than one portable to one extension number.  
If a portable telephone is used in more than one Norstar  
or Companion system, its owner must know which  
registration slot number was used to register the portable  
telephone with each system. (It is preferable that each  
user register the system they use most in slot 1.)  
If a portable telephone is lost or broken, you can  
deregister it from the system before replacing it with  
another portable telephone.  
MICS-XC Norstar-Companion Installer Guide  
P0881594 Issue 02  
 

National Instruments Network Router cFP RTD 122 User Manual
NeumannBerlin Microphone EA 30B User Manual
Nextar Projector XPJ User Manual
Nilfisk ALTO Vacuum Cleaner 114RS SWEEPER User Manual
Nokia Car Speaker MD 5W User Manual
Olympus Camera Lens 261009 User Manual
Oregon Scientific Clock RRM612PA User Manual
P3 International Indoor Furnishings P7400 User Manual
Panasonic Patio Furniture EP3203 User Manual
Panasonic Ventilation Hood FBA11J10M User Manual