Nokia Carrying Case LPS 4 User Manual

Inductive Loopset LPS-4  
User Guide  
9354812  
Issue 3  
 
The availability of particular products may vary by region. Please check with the Nokia dealer nearest to  
you.  
Unauthorized changes or modifications to this device may void the user's authority to operate the  
equipment.  
Export Controls  
This device may contain commodities, technology or software subject to export laws and regulations from  
the US and other countries. Diversion contrary to law is prohibited.  
9354812 / Issue 3  
 
1. General  
The Mobile Inductive Loopset LPS-4 for people with hearing aids is developed to  
facilitate the use of a compatible mobile phone together with T-coil equipped  
hearing aids.  
When using the inductive loopset, you can speak directly to the microphone inside  
it. You do not need to hold a mobile phone near your ear, but you can carry it using  
a carrying case, belt clip, or other accessory. The loopset does not require any  
separate batteries.  
The operation of the device is based on induction technology used in public  
places: a loop system sends out sounds wirelessly to be picked up by the telecoil of  
the hearing aid that is switched to the T mode.  
The device described in this guide is compatible with phones with a Pop-Port™  
interface connector (for example, the Nokia 6681 and Nokia 6682 mobile phones).  
The inductive loopset can also be connected to the speech processor of a  
compatible cochlear implant by using the audio output connector.  
Read this user guide carefully before using the loopset. Also read the user guide  
for your phone, which provides important safety and maintenance information.  
Keep the loopset out of reach of small children.  
For more information about loopsets and other accessibility solutions, visit our  
© 2006 Nokia. All rights reserved.  
4
 
2. Using the loopset  
Make and receive calls  
1. Place the loop around your neck, and connect the  
plug to its counterpart.  
2. Connect the Pop-Port plug to the bottom of the  
phone. The phone displays the following  
symbol:  
3. Switch your hearing aid to the T or MT mode.  
© 2006 Nokia. All rights reserved.  
5
 
4. To answer or end a call, press the answer button on the  
device or use the keys on your phone. Calls can be made in  
the normal way (see the user guide of your phone).  
Notes  
• The lead does not need to be connected to the Pop-Port connector of the  
phone all the time. You can choose to connect it only when you wish to make  
or receive calls.  
• When you receive a call, both the phone and the loopset sound an alert if the  
lead is connected to the phone and if the hearing aid is in the T or MT mode.  
• To adjust the volume of the loopset, use the volume keys of the phone. For  
normal use, keep the volume low, where you can clearly hear your own voice.  
In a noisy environment or if the received speech is weak, increase the volume  
so that the background noise becomes weaker and the caller’s voice becomes  
stronger.  
© 2006 Nokia. All rights reserved.  
6
 
Connect the loopset to external devices  
The loopset can be connected to a compatible speech processor  
of a cochlear implant or to the audio input of a hearing aid.  
Contact your hearing aid specialist for the compatibility with  
your cochlear implant or hearing aid, the correct connection  
cable, and instructions on the use of the connection cable.  
Connect the plug of the external device to the audio output  
connector with the symbol  
device.  
on the right side of the loopset  
© 2006 Nokia. All rights reserved.  
7
 
3. Technical data  
External audio output:  
• Connector: 3.5-mm socket  
• Can be connected to the audio input of a compatible hearing aid or to a  
compatible speech processor of a cochlear implant  
• Impedance: >1 k@ 1 kHz (nominal 2.2 k@1 kHz)  
• Typical output signal level: 0.5–10 mV rms  
• Symbol:  
The loopset can be connected to a compatible speech processor with a suitable  
cable that has a 3.5-mm stereo or mono plug. The sound that you hear through  
the loopset is monophonic.  
External audio input:  
• This feature is not available.  
• Symbol:  
© 2006 Nokia. All rights reserved.  
8
 
Care and maintenance  
Your device is a product of superior design and craftsmanship and should be treated with  
care. The suggestions below will help you protect your warranty coverage.  
Keep the device out of the reach of small children.  
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can  
contain minerals that will corrode electronic circuits. If your device does get wet, allow  
the device to dry completely.  
Do not use or store the device in dusty, dirty areas. Its electronic components can be  
damaged.  
Do not store the device in hot areas. High temperatures can shorten the life of electronic  
devices and warp or melt certain plastics.  
Do not store the device in cold areas. When the device returns to its normal temperature,  
moisture can form inside the device and damage electronic circuit boards.  
Do not attempt to open the device.  
Do not drop, knock, or shake the device. Rough handling can break internal circuit boards  
and fine mechanics.  
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.  
Do not paint the device. Paint can clog the moving parts and prevent proper operation.  
If the device is not working properly, take it to the nearest authorized service facility for  
service.  
© 2006 Nokia. All rights reserved.  
9
 

Miele Coffeemaker CVA 2650 User Manual
Miele Cooktop DA 200 2 User Manual
Multiquip Appliance Trim Kit MVH 402GHB User Manual
National Instruments Network Card NI 9871 User Manual
Nextar Digital Photo Frame N3 504 User Manual
Nortel Networks Network Router 11CM User Manual
Omega Vehicle Security Electric Heater DRF POT User Manual
Omron Fitness Electronics HJ 321 User Manual
Oregon Clock RM818PA User Manual
ParaBody Home Gym 916101 User Manual