Operation Manual
AN 8x30M22
Daytime Binoculars
NSN # 6650-20-007-7029
105 Sparks Ave., Toronto, ON M2H 2S5, Canada
6.7 Calculating target's size using angle readings.......14
7. STORAGE AND MAINTENANCE......................15
8. WARRANTY.........................................................16
9. CUSTOMER SUPPORT........................................18
10. QUALITY CERTIFICATE....................................19
1. BRIEF DESCRIPTION
The AN daytime binoculars AN 8x30M22,
The binoculars are designed and manufactured to military
specifications and provide excellent brightness, image
clarity and true image color. The built-in range finding
reticle, M22 standard, enables measurements of horizontal
and vertical angles, as well as calculation of height, width
of the target and distance to the target.
These binoculars are waterproof, shockproof and nitrogen
filled. They are also rubber armoured and have a tripod
socket.
The binoculars feature foldable rubber eye cups and long
eye relief to provide for comfort viewing with glasses or
mask. Though many binoculars feature fold down eye
cups, only the ones featuring a long eye relief offer a truly
full view while wearing glasses.
These binoculars meet the standards and requirements of
GJB1240, GJB150 and MIL-STD810.
The user can be confident whether the instrument is used
in the military, security, traffic control, marine, aviation,
or any other application requiring reliable and powerful
optical equipment.
1
2. SPECIFICATIONS
2.1 Shared specifications
Prisms
BAK4
FMC
Coating
Brightness index
50.4
Interpupillary adjustment distance
M22 Reticle
56-74 mm
Yes
Operating temperature range
–40°C … +70°C
All binoculars are waterproof and shockproof (will
withstand a drop test from 1.8m).
2
2.2 AN 8x30M22 detailed specifications
AN 8x30M22
Magnification
8x
Objective
lens diameter
30 mm
Focus
3 m – inf.
8°
Field of view
Apparent field of view
60°
FOV
@1000 m
132 m
396 ft
FOV
@1000 yd
Exit pupil
Eye relief
Weight
3.8 mm
17 mm
0.545kg
Dimensions, LxHxW, mm
110x156x55
3
3. DESIGN AND APPEARANCE
3.1 Optical design
Optical design of the binoculars is presented on Fig. 1.
1 – objective lens
3 – reticle lens
2 – erective prisms
4 – eyepiece
Fig. 1
The light from the object or target you are looking at
enters the binoculars through the objective lens system (1,
4
Fig. 1). Due to the objective lens, the image at this point
is turned upside down. However, as the image passes
through the prism system, (known as the erective prisms)
(2, Fig. 1) it becomes right side up (erect) and changed
from right to left, to left to right. After the prisms the
image rays pass through the reticle lens (3, Fig. 1) and
then through the eyepiece (4, Fig. 1).
3.2 Reticle
Reticle lens (3, Fig. 1) contains vertical and horizontal
lines that constitute an M22 reticle. Though reticle scales
may form a cross or upside down T (Fig. 2, B) they share
the same scale division value: each small division on both
vertical and horizontal lines is 5 mils and each big
division is 10 mils (360º equals 6400 mils).
Reticle may have an addition scale composed of two lines
(B, Fig.2).
Fig. 2
5
4. BODY ASSEMBLY
3
4
5
2
1
Fig. 3
1 – Objective lens
3 – Binocular body
5 – Eyepieces
2 – Objective protective cap
4 – Individual focus
adjustment rings
6
5. DELIVERY SET
Q-ty Notes
Binoculars
1
Carrying strap
Lens cleaning cloth
1
1
Soft case with carrying
strap
1
Eyepiece cover
Tripod adapter
Manual
1
1
1
7
6. OPERATION INSTRUCTIONS
6.1 Interpupillary distance adjustment
Prior to use you may like to adjust the binoculars to the
distance between your eyes (interpupillary distance).
Holding the binoculars in both hands rotate its halves
until you see one round image.
Note: The image may not be clear at this step. You will
focus it in the next step.
6.2 Focusing the binoculars
The binoculars have independent focus.
Independent focus
To focus the binoculars raise the instrument to your eyes
and close your right eye. With your left eye open focus
the image by rotating eyepiece adjustment ring of the left
eyepiece. Repeat the procedure for the other eye.
Note: You may like to remember your dioptre settings to
set them every time you use the binoculars.
8
6.3 Measuring horizontal angle using the reticle
An M22 reticle built into these binoculars enables
measuring height, distance and size of a target, as well as
angle between two close targets. Though reticle
appearance may differ from one model to another as
described in 3.2, the description below is valid for all
models.
When the angle between two targets is smaller than the
angle measuring range (100 mils), aim the scale line at
one end of the reticle at the target then read the value of
the scale at which another target was located on the
reticle. As shown in Fig. 4, the horizontal angle of the
target (tank) is 20 mils.
Fig. 4.
9
When the angle between two targets is larger than the
angle measuring range (100 mils), it can be measured in
several steps.
The horizontal angle of cruiser shown in Fig. 5, is 130
mils (60+70=130).
Fig. 5.
Vertical angle measurement is similar to horizontal angle
measuring.
When height of the target is smaller than the reticle scale,
its height can be obtained in one measurement.
The height of the beacon, shown in Fig. 6, is 65 mils.
10
For targets taller than the reticle scale, perform
measurement in steps in the same way as it is described
for the horizontal angle measurement.
Fig. 6.
11
6.5 Using the reticle to calculate distance
To determine the distance to the target use the formula:
D = H/K,
where
D – distance to target in km,
H – estimated height of the target in m,
K – vertical angle of the target in mil.
First, estimate the height (or width) of the target, then
measure target’s horizontal (vertical) angle and calculate
the distance.
For example:
Assuming an image of an adult human figure has a
vertical angle of 10 mils and its height is 1.70m we can
calculate the distance to it:
L=H/K=1.7/10=0.170 (km) = 170 (m)
6.6 Measuring distance directly using the reticle
If reticle of your binoculars has an additional scale shown
at Fig.7 distance to a target may be measured directly.
12
Fig. 7
Place the lower edge of the target at the horizontal line on
the reticle. The reading of the scale at the point where
target’s 2 m level touches the scale is the distance in
meters.
Assuming that vehicle on the Fig. 7 is 2 m high; the
distance to it is 550m.
13
6.7 Calculating target's size using angle readings
To calculate height and width user will need to estimate
the distance to the target and measure its horizontal and
vertical angles. Then using the formula for distance
measurement one can calculate target’s height:
H=DxK,
where K is vertical angle in mils,
D is distance in meters and
H is height in meters.
For example: if distance to the target is 0.6 km and its
horizontal angle is 30 mils and its vertical angle is 60
mils, using the formula you can calculate:
The height: H=0.6 x 30= 18 m
The width: W=0.6 x 60=36 m
14
7. STORAGE AND MAINTENANCE
The binoculars are precision optical instruments that
should be carefully handled and properly maintained to
keep them in a good working order.
Clean the lenses after each use with special optical cloth.
Never wipe the lenses with fingers; grease may damage
the optics coating. Never use anything to wipe the lenses
except special optical cleaning cloth.
The eyepieces provide a wide dioptre adjustment; do not
turn them beyond the factory set stop. Forcing eyepieces
beyond this point will cause damage and make the
binoculars inoperable.
Avoid any extreme vibration or shock of the binoculars.
This may damage the internal optics.
Store the binoculars in a dry well ventilated place.
If you find the binoculars not working properly, do not
attempt repairing it yourself as this may void any
warranty. Always deliver the binoculars to a professional
optics repair. If one is not readily available, then send it
back to the factory.
15
8. WARRANTY
NEWCON warrants this product against defects in
material and workmanship for one year from the date of
the original purchase. Longer warranty is available,
subject to the terms of the specific sales contract. Should
your Newcon product prove to be defective during this
period, please deliver the product securely packaged in its
original container or an equivalent, along with the proof
of the original purchase date, to your Newcon Dealer.
Newcon will repair (or at its option replace with the same
or comparable model), the product or part thereof, which,
on inspection by Newcon, is found to be defective in
materials or workmanship.
What This Warranty Does Not Cover:
NEWCON is not responsible for warranty service should
the product fail as a result of improper maintenance,
misuse, abuse, improper installation, neglect, damage
caused by disasters such as fire, flooding, lightning,
improper power supply, or service other than by a
NEWCON Authorized Service.
Postage, insurance, and shipping costs incurred while
presenting your NEWCON product for warranty service
16
are your responsibility.
If shipping from North America please include a cheque
or money order payable to NEWCON OPTIK for the
amount of $15.00 to cover handling and return shipping.
17
9. CUSTOMER SUPPORT
Should you experience any difficulties with your
NEWCON OPTIK product, consult the enclosed manual.
If the problem remains unresolved, contact our customer
support department at (416) 663-6963 or toll free at 1-
877-368-6666. Our operating hours are 9am-5pm,
Monday - Friday, Eastern Standard Time.
At no time should equipment be sent back to Newcon
without following the instructions of our technical support
department.
NEWCON OPTIK accepts no responsibility for
unauthorized returns.
To locate NEWCON Authorized Dealer call:
Tel: (416) 663-6963 Fax: (416) 663-9065
Email: [email protected]
Defective products should be shipped to:
From all countries:
105 Sparks Ave., Toronto, ON M2H 2S5, CANADA
18
10. QUALITY CERTIFICATE
The binoculars serial number_______________________
complies with all technical specifications and has passed
the inspection.
Date of production:
_________________________________
Quality Inspector:
__________________________________
Quality Assurance Seal
19
NEWCON OPTIK
Printed in Canada
|