National Instruments Network Card FP 3000 User Manual

OPERATING INSTRUCTIONS  
FP-3000  
FieldPoint Fieldbus Network Module  
This document provides a quick guide to install and configure the  
FP-3000 network module. For more detailed information on using  
the network module, refer to the FP-3000 user manual.  
Features  
FOUNDATION Fieldbus H1 interface to control network  
Runs on 11 to 30 VDC power  
Built-in high efficiency power supply powers I/O modules  
–40 to +60 °C operation  
Kit Contents and Optional Equipment  
Your kit contains the following items:  
FP-3000 network module  
Accessories: protective connector cover, two DIN rail stops,  
Device Description diskette  
You can order the following optional equipment from National  
Instruments:  
Panel mount accessory, part number 777609-01  
Terminal bases and I/O modules, complete list of terminal  
bases and I/O modules in the National Instruments online  
Cables  
24 VDC power supply  
FieldPoint is a trademark of National Instruments Corporation. Product and company names  
mentioned herein are trademarks or trade names of their respective companies.  
322170B-01  
© Copyright 1999 National Instruments Corp. All rights reserved.  
June 1999  
 
b. Slide the FP-3000 to the desired position along the  
DIN rail.  
c. Lock the rail clip.  
Installing onto a panel mount accessory, which you can  
order separately from National Instruments:  
a. Snap the panel mount accessory onto the module  
as shown in Figure 3.  
Press  
Figure 3. Mounting the FP-3000 onto a Panel Mount Accessory  
b. Lock the rail clip.  
c. Mount the FP-3000 and panel mount accessory onto  
the desired surface. You can drill pilot holes using the  
directions in the FieldPoint Network Module Panel  
Mount Accessory installation guide.  
3. Add terminal bases with their local bus connectors firmly  
mated to the FP-3000 local bus connector.  
4. Place the protective cover over the local bus connector of the  
last terminal base in the bank. Figure 4 shows an installed  
FP-3000 network module on a DIN rail.  
© National Instruments Corp.  
3
FP-3000  
 
 
Local Bus Connectors  
Firmly Mated  
Protective  
Cover  
Rail Clip  
Locked  
DIN  
Rail  
Figure 4. Network Module and Terminal Base Mounted on a DIN Rail  
Network Connection  
Connect the FP-3000 to a Fieldbus network using the 9-position  
DSub connector on the FP-3000. The pinout of the DSub connector  
is shown in Figure 5.  
1
2
3
4
5
6
7
8
9
NC = No Connection  
Figure 5. Dsub Connector Pinout  
FP-3000  
4
 
   
Powering the FP-3000  
Caution Connect the FP-3000 to the terminal base before  
applying power to the FP-3000 to avoid damaging the  
FP-3000 or a terminal base.  
An 11-30 VDC power supply is required by each FP-3000 on your  
network. The FP-3000 filters and regulates this supplied power and  
provides power for all the I/O modules in the bank. Therefore, you  
do not need to provide power separately to each FieldPoint I/O  
module in the bank. If your field I/O devices need to be powered  
separately, you can use the terminals provided on each terminal  
base for such power supply connections.  
The power connector is a 6-pin screw terminal connector whose  
pinout is shown in Figure 6.  
v
v
v
11-30 VDC  
V
+
Backup Power  
Supply  
(optional)  
c
To adjacent device  
(optional connection)  
c
c
C
11-30 VDC  
Primary Power  
Supply  
+
Figure 6. FP-3000 Power Connector Pinout  
Connect the primary power supply to the center V and C pair. You  
can connect an optional backup power supply to the left V and  
C pair. The right V and C pair provides a convenient means of  
connecting power to the V and C terminals of a terminal base.  
Figure 6 shows this optional connection.  
Specifications  
FP-3000.............................................FOUNDATION Fieldbus H1  
Integrity.............................................Checksum  
Power supply range...........................11 to 30 VDC  
Maximum terminal bases/bank.........9  
© National Instruments Corp.  
5
FP-3000  
 
 
Maximum banks/fieldbus  
Segment (without repeaters).............32  
Power consumption...........................6 W + 1.15 * (I/O module  
consumption)  
Operating temperature ......................40 to +60 °C  
Storage temperature..........................55 to +100 °C  
Relative humidity..............................5% to 90% non-condensing  
CE Mark Compliance  
This product meets applicable EU directive(s) as follows:  
EMC directive  
Immunity....................................EN 50082-1:1994  
Emissions ...................................EN 55011:1991 Group I  
Class A at 10 meters  
Mechanical Dimensions  
Figure 7 shows the mechanical dimensions of the FP-3000.  
Dimensions are given in inches [millimeters].  
4.22 [107.19]  
4.31  
[109.5]  
3.60 [91.44]  
Figure 7. Mechanical Dimensions  
FP-3000  
6
 
 
 

MTD Chainsaw 1425NAV User Manual
Murphy Switch Electric Gage and Swichgage User Manual
National Instruments Personal Computer PXI 1411 User Manual
Network Computing Devices Network Card IN2000 User Manual
Nikon Photo Scanner FH 869G User Manual
Omega Crib Toy DP3001 User Manual
Oster Mixer 2382 User Manual
P3 International Vacuum Cleaner P4920 User Manual
Panasonic Air Conditioner CS C12DKU User Manual
Panasonic Webcam DMC SZ9 User Manual