NHT Speaker 29 User Manual

Model 2.9  
Tower Loudspeaker  
OWNER’S MANUAL  
Now Hear This  
6400 Goodyear Road, Benicia, CA 94510  
800-NHT-9993  
 
Placement  
The Model 2.9 is a floorstanding tower speaker that requires no stands or mounting hardware other than the included SpikeKit. The  
Model 2.9 is designed for indoor use only. As the Model 2.9 is not a magnetically shielded loudspeaker, do not place it closer than 18  
inches from a television. Unshielded magnets placed in close proximity to a television screen can cause discoloration of the picture. If  
you notice picture discoloration, move the speakers away from the TV until the problem disappears.  
The most impressive performance benefit of Focused Image Geometry is spectacular imaging and an expansive soundstage. To  
achieve this in your home, we recommend that the 2.9’s are situated 8 - 14 inches from the rear wall and at least 30 inches from the  
side walls. For smoothest response, the distance from the side walls should be different than the distance from the rear wall. The  
speakers should be arranged as symmetrically as possible, with their backs parallel to the rear wall and the drivers facing the listening  
area without obstruction from furniture. Arrange the speakers so that the distance between the listener and the center of the speaker  
plane is 1.5 times the distance between the speakers (fig.1). This configuration puts the listener in the center of the stereo image.  
Experimentation is the key to finding the best arrangement in your listening environment. Be patient, have fun, and remember that small  
changes in speaker position can sometimes have a significant effect on the sound. For example, moving the speakers nearer to a room  
boundary (walls, corners) will tend to increase their bass output, but may result in “boomy” or “muddy” sound. Conversely, placing the  
speakers farther away from room boundaries will tend to decrease their bass output, but may result in greater articulation and better  
imaging.  
In addition, room furnishings play an important role in absorbing and reflecting soundwaves. Midrange and high frequencies in  
par-  
ticular will be absorbed by soft furnishings such as sofas, carpets and curtains. A large number of these soft furnishings will dull the  
sound, while a “live” room with few furnishings will brighten the sound. If you are willing to spend some time fine-tuning the performance  
of your system, you will enjoy the benefits for years to come.  
fig. 1  
SpikeKit Installation  
A SpikeKit is included with the Model 2.9 to provide optimum stability and to firmly couple the speakers to the floor for improved bass  
performance. Each 2.9 loudspeaker is shipped with its own SpikeKit. Caution: the 2.9 is unstable without the SpikeKit (or at least  
the stabilizer bars) installed.  
To begin assembly, unpack the SpikeKit and inspect all the parts. The SpikeKit includes: (2) stabilizer bars, (4) metal cones, (4) Phillips  
head machine screws, (4) metal bolts and (4) rubber feet. We recommend installing the cones only after you have found the ideal  
location for the speakers. Begin by installing the stabilizer bars. Carefully turn the speaker upside down or on its back, and attach the  
stabilizer bars with the Phillips head machine screws, using a #3 Phillips screwdriver (fig. 2). Note: When installing the bars onto the  
bottom of the speaker, use your fingers to start all the machine screws in their holes before tightening them down. This will  
prevent crossthreading.  
Before installing the cones, turn the speakers upright and position them. Once you have found the ideal location, carefully tilt the  
speakers and screw in the cones. The speakers are awkward to move after the cones are installed. Caution: The cones are very  
sharp. To avoid injury, use extreme care when handling and installing them. Adjust the spikes as needed to ensure that the 2.9  
is level and does not rock in any direction. Use the metal bolts to lock the cones in position. If you have hardwood floors or floors with  
a scratchable surface, you may choose not to use the cones because they will pierce the surface. Rubber feet are provided and can  
be used in place of the cones. Install the stabilizer bars, peel off the adhesive backings from the rubber feet, and place them over the  
holes where the cones would screw in.  
3
 
Connections  
Before connecting speakers to your system, it is very important that you turn off the power to your amplifier / receiver to avoid  
damage to the equipment.  
The Model 2.9 loudspeaker system is compatible with virtually all quality amplifiers. Proper wiring of the speakers is essential to good  
sound. At a minimum, 14AWG speaker cable is recommended for runs of 10 feet or less, with heavier special purpose cable used for  
longer runs. For specialty cable considerations, consult your local authorized NHT retailer. For best results, use equal length runs of  
cable for the left and right speakers. Prepare your cable by stripping 1/4” to 3/8” of insulation from the ends and twisting the exposed  
wire strands tightly. The five-way binding posts on the back of the speaker will accept raw wire, banana plugs, or spade plugs. Tighten  
the binding posts by hand, as pliers can strip or break them.  
Be sure to wire both the left and right speakers "in-phase." That is, the Positive (red) terminal on the amplifier output must be  
connected to the corresponding Positive (red) terminal on the speaker. Likewise with the Negative (black) terminals. All  
speaker cables have some sort of marking along one or both conductors to help you make the correct connections. Incorrect speaker  
phase is indicated by weak bass and the lack of a well-defined stereo image.  
To minimize noise pickup, segregate cables by function. Do not run low level signal cables parallel to power cables, speaker cables, or  
digital cables. Also, do not run speaker cables or digital cables parallel to power cords or parallel to each other. If different types of  
cables are placed near each other at some place in your system, separate them by the maximum practical distance and cross them at  
right angles where they meet. Do not twist or tie AC power cords and speaker cables.  
Connection Methods  
fig. 3  
On the back panel of the 2.9 there are two pairs of binding posts (fig. 3) with  
a metal jumper strap connecting the top and bottom pairs. There are three  
different ways to connect the 2.9’s to your system: full range with a single  
amplifier, biamplified with two amplifiers and two sets of speaker cable, or  
biwired with one amplifier and two sets of speaker cable.  
Full Range  
To run the 2.9’s full range with one amplifier / receiver, simply connect the  
speaker cables to either the top set or bottom set of binding posts  
(it doesn’t matter which one).  
Biamplification  
Biamplification is the use of two separate amplifiers, one to power the bass drivers and one to power the midrange / high frequency drivers.  
Biamplification provides increased dynamic range and power output, as it allows both amplifiers to concentrate all their headroom toward a  
specific frequency range, sparing them the task reproducing full range information.  
To biamplify the 2.9, you will need two amplifiers: a main amplifier for the upper range drivers (top pair of binding posts) and a second amplifier  
for the subwoofers (bottom pair). The main amplifier can be a stand-alone stereo amplifier, dual monoblock amplifiers, or the amplifier section of  
an integrated amplifier or audio/video receiver that features “pre-out” and “main-in” jacks. The second amplifier may be a full range amplifier  
connected parallel to the main amplifier, or for more flexibility, the NHT SA-3 subwoofer amplifier.  
Biamplifying with the SA-3 is highly recommended, as this configuration turns the passive subwoofer section of the 2.9 into a fully adjustable  
powered subwoofer with onboard bass tuning functions. The SA-3 is optimized for low frequency amplification and allows the user to fine-tune  
the 2.9’s bass response for a specific listening environment. For example, it is possible to increase or decrease the volume level of the subwoofer  
sections independently of the upper driver sections, to compensate for rooms that tend to under-emphasize or over-emphasize low frequencies.  
Additionally, the SA-3’s low-pass crossover allows the user to adjust the rolloff of low frequencies to the subwoofer sections for further fine-tuning  
of the low bass and mid-bass regions.  
Note: It is very important that you remove the jumper straps when biamplifying or you will damage your amplifiers! Connect the top  
pair of binding posts with speaker cable from the main amplifier, and the bottom pair of binding posts with speaker cable from the second  
amplifier. If you are biamplifiying with two full range stereo amplifiers that are not identical, make sure that one has an adjustable volume control  
so that you can match levels between the two. Both amplifiers will need to be wired in parallel from the preamplifier, so that they both receive an  
identical line-level input signal.  
If you are biamplifying with the SA-3 subwoofer amplifier, it may be connected in series or in parallel. For more detailed information, consult the  
SA-3 Owner’s Manual or your local authorized NHT retailer.  
Biwiring  
Some audio enthusiasts have found that biwiring can bring about improvements in sound. Biwiring is the use of two pairs of speaker cable and  
one amplifier, with each pair connected to one set of binding posts on the amplifier (some two-channel amplifiers provide two sets). To biwire  
the 2.9’s, connect the top pair of binding posts to the amplifier with one speaker cable, and the bottom pair with a second cable. The  
two sets of speaker cable are both connected to the same pair of terminals on the amplifier.  
4
 
Operation  
The Model 2.9 was designed to handle a wide range of listening levels, but every speaker has limits. It is important to use common  
sense and listen for signs of possible distress from the speakers. Underpowered amplifiers are most often the cause of speaker  
damage. For example, a 60-watt amplifier runs out of power when called upon to produce more than 60 watts, and the resulting  
distortion can damage the speaker. If you tend to listen at high volume levels, more powerful amplifiers are preferable because they are  
less likely to run out of power.  
Noticeable distortion or harsh breakup is an indication that either your amplifier or your speakers are running beyond their capacity, and  
the volume should be decreased. If you can feel any heat emanating from the woofer or tweeter, reduce the level immediately. Speaker  
damage most often occurs from sustained high volume levels, not from transient sounds or brief musical peaks. Excessive boosting of  
bass, treble or equalizer controls can worsen the problem, and is not recommended.  
Maintenance  
Your speakers require minimal maintenance under normal use. The cabinet may be cleaned using a damp cloth or a mild, non-abra-  
sive cleaner. To clean the grille, first remove it from the speaker, then brush lightly with a soft brush or use a vacuum on its lowest  
setting. Do not expose the speakers to direct sunlight, high temperatures, or moisture. Do not attempt to clean the actual drivers.  
Limited Warranty  
Valid Only in the U.S.A.  
Warranty Period  
For the period of 5 years for parts and 5 years for labor from date of original purchase (the warranty period) from an authorized NHT  
dealer, Now Hear This (NHT) warrants that if our product fails to function properly under normal use due to a manufacturing defect  
when installed and operated according to the owner’s manual instructions enclosed with the unit, it will be repaired or replaced with  
a unit of comparable value at the option of NHT without charge to you for parts or actual repair work. Parts supplied under this  
warranty may be new or rebuilt at the option of NHT.  
What’s Not Covered  
This warranty does not cover any product which is used in any trade or business, or in an industrial or commercial application.  
This warranty does not cover the cabinet or any appearance item, or any damage caused to the product resulting from: alterations,  
modifications not authorized in writing by NHT, accident, misuse or abuse, damage due to lightning or power surges, or being  
subjected to power in excess of the speaker’s published power rating.  
This warranty does not cover the cost of parts which would otherwise be provided without charge under this warranty, obtained from  
any source other than an authorized NHT service location. This warranty does not cover defects or damage caused by the use of  
unauthorized parts or labor or from improper maintenance.  
Altered, defaced or removed serial numbers void this warranty.  
Your Rights  
The liability of NHT will be limited to the purchase price of the product, and NHT will not be liable for incidental or consequential  
damages. NHT limits its obligations under any implied warranties under state laws to a period not exceeding the warranty period.  
Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation  
of incidental or consequential damages. The above limitations or exclusions may not apply to you. This warranty gives you specific  
legal rights, and you may have other rights which vary from state to state.  
To Obtain Service  
NHT has appointed a number of authorized service companies throughout the USA should your product ever require service. To  
receive warranty service, you will need to present your sales receipt showing place and date of original owner’s transaction.  
To find the name and address of the nearest authorized NHT service location, call or write: Customer Service Department, Now  
Hear This, 6400 Goodyear Road, Benicia, CA 94510. 800-NHT-9993.  
Please do not return product to this address. It is not a service location.  
Keep this warranty with your sales receipt.  
Record date and place of purchase for future reference.  
5
 

Mr Coffee Espresso Maker ECMP2 User Manual
NCR Wireless Office Headset 5953 User Manual
Netopia Network Router R2121 User Manual
Novatel Stereo System SMART ANTENNA User Manual
Oki Printer 8z User Manual
Olympus Camcorder D200 L User Manual
Omega Switch C4EIT EIT User Manual
Onkyo Stereo System TX SR800 User Manual
Outback Power Systems Power Supply Sealed FX User Manual
Parkside Paint Sprayer PFSP 100 User Manual