NETGEAR Switch GS105NA User Manual

GS105v4_IG 2Mar10.fm Page 1 Wednesday, March 2, 2011 12:32 PM  
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear  
space on all sides of the switch.  
4. Check the LEDs to verify that the equipment is connected correctly.  
100 Mbps  
Installation Guide  
Well ventilated (especially if it is in a closet).  
Depending on the speed of your network devices, you need a Category 3 (10  
Mbps), Category 5 (100 Mbps) or Category 5e (1000 Mbps) Ethernet cable with RJ-  
45 connectors for each device you want to connect to the switch. Each Ethernet  
cable must be less than 328 feet (100 meters).  
10 Mbps LED  
Power  
Both LEDs light for  
a 1000 Mbps connection.  
ProSafe 5-Port Gigabit Ethernet Switch GS105v4  
The Power LED is lit.  
Install the Switch and Connect the Other Devices  
Each RJ-45 jack has 2 LEDs. For each jack that is connected to a powered  
device, the Link LED is lit, and it flashes when activity occurs. If the  
connection is 10 Mbps or 100 Mbps, one LED lights up. If the connection is  
1000 Mbps, both LEDs light up.  
Estimated installation time: 5-10 minutes  
1. Place the switch on a flat surface or hook onto the screws.  
2. For each device, insert one end of an Ethernet cable into the port in the device  
and insert the other end into one of the Ethernet ports on the switch.  
Note: If any light does not operate as indicated, go to the Troubleshooting section.  
Troubleshooting  
The Power light is not lit.  
The switch has no power.  
Make sure that the power cord is correctly connected to the switch.  
broadband  
modem  
Package Contents  
Make sure that the power adapter is connected to a functioning power outlet. If it  
is in a power strip, make sure that the power strip is turned on. If the socket is  
controlled by a light switch, make sure that the switch is in the on position.  
The package includes:  
ProSafe 5-Port Gigabit Ethernet Switch GS105v4  
AC power adapter  
Make sure you that are using the NETGEAR power adapter supplied with your  
switch.  
firewall  
GS105v4 Installation Guide (this document)  
Warranty/Support information card  
GS105v4 5-Port  
Gigabit Ethernet Switch  
The Port number light is not lit for a connected device or stays on continuously.  
3. Connect the power adapter cord into the back of the switch and then plug the  
There is a hardware connection problem.  
adapter into a power source (such as a wall socket or power strip).  
Prepare to Install the Switch  
Make sure that the cable connectors are securely plugged in at the switch and  
the device.  
Decide where you want to place the switch. Find a flat horizontal surface such as a  
table, desk or shelf. You can use wall-mounting screws (not provided) to hang the  
switch in an open space on a wall.  
Make sure that the connected device is turned on.  
If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure  
that the card or adapter is installed correctly and is working.  
Make sure the selected location is:  
Make sure that the cable is less than 328 feet (100 meters).  
Not in direct sunlight or near a heater or heating vent.  
 

MTD Tiller 219 100 User Manual
Murphy Home Security System SAH User Manual
Nady Systems Musical Instrument SPM 6300 User Manual
Nikon Camera Lens 1913 User Manual
Niles Audio Stereo System VCS50 User Manual
Nostalgia Electrics Bread Maker BMM100 User Manual
Optoma Technology Projector H27 User Manual
Panasonic Camcorder AJ D910WAP E User Manual
Panasonic Car Video System CQ VA707N User Manual
Paradyne Appliance Trim Kit 727 User Manual