Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT.
expert technical support and timely notices of product and software upgrades.
Fast Ethernet Switch
10/ 100 Mbps FS105 v2/ FS108 v2
NETGEAR, INC.
Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support
See Support Information card for other countries.
E-mail: [email protected] (24 x 7 online support)
© 2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and
Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the
United States and/or other countries. Microsoft and Windows are registered trademarks of
Microsoft Corporation in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is
subject to change without notice. All rights reserved
Installation Guide
July 2004
2 0 1 - 1 0 2 4 9 - 0 1
Unpack the Box and Verify the
Contents
Prepare to Install the Switch
1
2
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf. The switch comes with wall-mounting screws. You’re welcome to use the screws if
you want to hang the switch in an open space on a wall.
Fast Ethernet Switch FS105 v2/FS108 v2
Make sure the selected location is:
•
•
Not in direct sunlight or near a heater or heating vent.
FA
ST
ET
HE
RN
ET
SW
ITC
H
F
S1
08
Auto
1
0/100
M
bps
On
Blin
=L
k=
ink
Ac
100M
10M
t
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
PW
R
1
2
3
4
5
6
7
8
•
Well ventilated (especially if it is in a closet).
Wall-mount
hardware
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).
Installation guide,
warranty/registration card
and support
Power adapter
information card
When you open the box, verify that you received everything. The package includes:
•
•
•
•
•
5/8-Port Fast Ethernet Switch FS105 v2/FS108 v2
AC power adapter
Wall-mounting screws
FS105 v2/FS108 v2 Installation Guide (this document)
Warranty and support information card
If you don’t have everything listed above, see the support information card for contact
information. If you’re missing the Technical Support information card itself, get contact
Install the Switch and Connect the Other
Devices
Troubleshooting
The Power light is not lit
The switch has no power.
3
•
•
Make sure the power cord is properly connected to the switch.
Make sure the power adapter is properly connected to a functioning power outlet. If it’s in
a power strip, make sure the power strip is turned on. If the socket is controlled by a light
switch, make sure the switch is in the on position.
•
Make sure you are using the NETGEAR power adapter supplied with your switch.
The Link/Activity is not lit for a connected device or stays
on continuously
There’s a hardware connection problem.
•
•
•
Make sure the cable connectors are securely plugged in at the switch and the device.
Make sure the connected device is turned on.
If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
•
Make sure the cable is less than 328 feet (100 meters).
Technical Specifications
Standards Compatibility:
Data Rate:
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet
1. Place the switch on a flat surface or hook onto the screws.
IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux®
2. For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
Network Interface:
DC Power:
RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
7.5W max and 7.5V @ 1A DC input
Note: If you have more than 5 or 8 devices to connect to this switch, you must
connect them to a hub or other switch and then connect that hub or switch to this
switch.
Physical Dimensions:
FS105 v2 - W: 94.8 mm (3.73") D: 101 mm (3.98") H: 27 mm (1.06")
FS108 v2 - W: 158 mm (6.22") D: 101 mm (3.98") H: 27 mm (1.06")
FS105 v2 - 0.275 kg (0.6 lbs); FS108 v2 - 0.49 kg (1.08 lbs)
0 to 40˚ C (32 to 104˚ F)
Weight:
Operating Temperature:
Operating Humidity:
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
10% t0 90% relative humidity, non-condensing
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B,
C-Tick
The Power light should light up.
Safety Agency Approvals for
the Power Adapter:
CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick
The corresponding port number for each connected and powered device should light
when link (connection), and flash when activity occurs.
Performance Specifications
Frame Filter Rate:
Frame Forward Rate:
Network Latency:
(using 64-byte packets)
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
100 Mbps to 100 Mbps: 20 µs max
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.
Address Database Size:
Addressing:
1024 MAC addresses
48-bit MAC address
Queue Buffer:
FS105 v2 - 64 kilobytes; FS108 v2 - 96 kilobytes
|