NETGEAR Network Router FVS336G User Manual

2. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE  
Warning: Failure to restart your network in the correct sequence could prevent you  
)NSTALLATION 'UIDE  
from connecting to the Internet.  
FVS336G ProSafe™ VPN Firewall  
Note: To connect to the firewall, your computer needs to be configured to obtain  
an IP address automatically via DHCP. If you need instructions on how to do this,  
please refer to the online reference manual. A link to the manual is on your  
Resource CD.  
a. First, power on the broadband modems. Wait approximately 2 minutes until they  
power up.  
Start Here  
b. Now, power on the FVS336G by plugging in the power cord that came with your  
router (4) and turning on the device (5).  
b. For security reasons, the firewall  
has its own user name and  
password.  
Follow these instructions to set up your firewall. You can also consult the online FVS336G  
ProSafe VPN Firewall Reference Manual or the NETGEAR Knowledgebase at http://  
kbserver.netgear.com. A link to the online Reference Manual is on the Resource CD.  
c. After the Test LED (7) extinguishes, turn on your computer.  
d. Before configuring your FVS336G, check the status LEDs to verify the  
following:  
When prompted, enter admin for  
Prepare to Install Your FVS336G VPN  
Firewall  
the firewall User Name and pass-  
word for the firewall Password.  
geardom  
c. Click Login. You are now  
connected to the firewall. The  
Router Status screen will display.  
This guide provides instructions for setting up a simple dual WAN port rollover  
configuration. Refer to the Reference Manual for other WAN port configuration options.  
8
9
10  
7
10  
8
9
6
Power. The power LED (6) should turn solid green. If it does not turn solid  
green, see the Troubleshooting section Reference Manual.  
The Web Support tab on the main menu contains links to the online NETGEAR  
FVS336G product documentation and support Knowledgebase. Be aware that the  
default login time-out is 5 minutes of inactivity, after which automatic logout will  
occur.  
First, Connect the FVS336G  
Test. When you first turn on the router, the amber test LED (7) will be lit for  
approximately 2 minutes. If it is still on after several minutes, see the  
Troubleshooting Tips below.  
1. CONNECT THE CABLES BETWEEN THE FVS336G, THE MODEMS, AND A  
COMPUTER  
WAN. The Active LEDs on WAN Port 1 and WAN Port 2 should be lit (8). If  
not, make sure the Ethernet cables are securely attached to the modems and  
the WAN ports, and that the modems are powered on. The Link/Act LEDs  
(9) indicate activity over the port. The Speed LEDs (10) respond as follows:  
green indicates your computer is communicating at 1 Gbps; amber indicates  
communication at 100 Mbps; no light indicates communication at 10 Mbps.  
2. CONNECT TO THE INTERNET  
a. Turn off and unplug the broadband modems.  
a. Select WAN Settings > WAN1 ISP Settings. The WAN 1 ISP Settings screen  
will display.  
LAN. The LAN ports Speed and Link/Act LEDS should respond in the same  
2
4
manner as the WAN ports for the connected LAN ports.  
5
1
3
b. Insert an Ethernet cable from a modem into the WAN1 port (1) of the FVS336G.  
Next, Configure the FVS336G for Internet  
Access  
a. Click Auto Detect at the bottom of the WAN1 ISP Settings screen. The router  
will automatically attempt to detect your connection type. If you know your ISP  
connection type, you can manually configure the router settings on the WAN1  
ISP screen. If connecting manually, click Apply to save your settings.  
c. Insert an Ethernet cable from the other modem into the WAN2 port (2) of the  
FVS336G.  
d. Insert the Ethernet cable that came with your firewall into a LAN port on the  
router (3) and insert the other end into the Ethernet port of your computer.  
Before you begin, be sure you have the configuration parameters from your ISP handy.  
b. When finished, click Test to verify that the Internet connection is active.  
1. LOG IN TO THE ROUTER  
Your network cables are connected and you are ready to restart your network.  
c. Select the WAN2 ISP tab and complete the same steps you just completed in  
steps a and b.  
 

Multi Tech Systems Network Card MT5634ZBA VV90 User Manual
NEC Flat Panel Television LCD3215 User Manual
Nortel Networks Switch Optivity Switch User Manual
Nortel Networks Telephone NT8B45AAAB User Manual
Novatel Radio Antenna SMART V1 User Manual
Oreck Vacuum Cleaner XL5 105HH User Manual
Oregon Home Security System UVN800 User Manual
Palsonic CRT Television 5180G User Manual
Panasonic Computer Accessories AS09A51 User Manual
Panasonic Computer Drive CF VFS372 User Manual