NETGEAR Network Card WG111T User Manual

You will also be prompted to choose the country you are located in. Select  
your location from the list.  
Windows XP  
)NSTALLATION 'UIDE  
d. Click Finish to complete the installation. You will see the  
WG111T system tray icon on the lower right portion of the  
Windows task bar.  
WG111T Wireless USB 2.0 Adapter  
1. First, install the WG111T software.  
a. Power on your PC, let the operating system boot up completely, and log in as  
needed.  
These basic setup instructions assume that you will connect to an access point, and you are  
not using WEP security. Please refer to the online help and the Reference Manual on your  
CD for instructions on configuring security, Ad-hoc mode, or advanced options.  
b. Insert the Resource CD for the WG111T into  
your CD-ROM drive. The CD main page  
3. NOW, CONFIGURE YOUR WG111T AND SAVE THE PROFILE.  
Estimated Completion Time: 5-15 minutes for a notebook PC.  
shown below will load.  
a. Click the  
icon in the Windows system tray to open the WG111T Smart  
c. Click the Install Driver & Utility link.  
Wireless Settings Utility.  
Place the USB Adapter Cradle  
d. Follow the InstallShield Wizard steps. You will  
be prompted to choose the country you are  
located in.  
The utility opens to the  
Settings tab page.  
You can attach the WG111T Wireless USB 2.0 Adapter  
directly to a USB port on your computer, or use the USB  
cable to extend the range and obtain better wireless  
reception.  
b. Change the Network  
Name SSID to match  
your network.  
e. Click Finish when done. If prompted by a Found New Hardware Wizard to  
install a “bootloader device,” do so. Restart your computer, if prompted.  
Tip: To view the  
Follow these instructions to use the USB cable, plastic  
cradle, and velcro provided in the package for better USB  
Adapter placement on a notebook or desktop computer:  
2. NEXT, INSERT THE WG111T WIRELESS USB 2.0 ADAPTER.  
available wireless networks, use the drop-down list or the Networks tab and  
choose the one you want.  
a. Locate an available USB port on your PC. Connect the USB cable to the  
WG111T and insert the other end of the cable into the USB slot on your PC.  
c. Click Apply to activate the connection.  
b. After a short delay,  
Tip: Create work and home profiles. Then, activate whichever one you need for  
your current location.  
Note: If a Windows  
XP logo testing  
warning appears, click  
Continue Anyway to  
the Found New  
Hardware Wizard  
displays. Select  
Install the software  
1. The WG111T Wireless USB 2.0 Adapter comes with  
3 pieces of velcro. Locate the one that has a prickly side and  
attach it to the plastic cradle on the middle of the outside rear.  
4. FINALLY, VERIFY WIRELESS NETWORK CONNECTIVITY.  
2. Insert the WG111T Wireless USB 2.0 Adapter in the plastic  
cradle.  
a. Verify that the status monitor information at the bottom of the utility matches  
your wireless network.  
proceed.  
automatically  
(Recommended) and  
click Next.  
3. Place one of the other pieces of velcro on the back of your  
notebook monitor near the top for better reception.  
b. Check the color of the WG111T icon in the Windows system tray: green or  
yellow indicates a working connection; red indicates no connection.  
c. Next you will be  
Note: The last piece of velcro can be placed on the side of your PC monitor nearest  
your wireless access point, if you are using the USB Adapter with a desktop PC.  
c. Check the WG111T LED: blinking means attempting to connect; solid indicates a  
good connection; off means the WG111T is not plugged in.  
prompted to enable  
the NETGEAR Smart Wireless Settings Utility configuration utility.  
4. Join the pieces of velcro to attach the USB Adapter in the plastic cradle to the  
notebook or desktop monitor.  
d. Verify connectivity to the Internet or network resources.  
Click Yes to accept this option.  
If you choose No, you must  
read the Windows XP  
documentation for an  
explanation of how to use the  
Windows XP wireless network  
Note: If you are unable to connect, see the Troubleshooting chapter of the  
Reference Manual on the NETGEAR 108 Mbps Wireless USB 2.0 Adapter  
WG111T Resource CD.  
See the installation instructions for your operating system before attaching the USB cable  
to the USB Adapter and your computer.  
configuration utility.  
 

National Instruments Portable Generator NI PXI 5422 User Manual
Nikon Camera Lens MH 52 User Manual
Nortel Networks IP Phone NN10300 025 User Manual
Olympus MP3 Player VN PC User Manual
Omega Engineering Computer Hardware OME A8111 User Manual
Oster Toaster TSSTRTS251 033 User Manual
Palsonic CRT Television 6140GY User Manual
Panasonic Car Stereo System CQ R545 User Manual
Panasonic Cell Phone EB G50 User Manual
Paradyne Network Hardware 8747 User Manual