NETGEAR Network Card SC101T User Manual

Install a Disk and Connect the SC101T  
Install the SC101T Software  
)NSTALLATION 'UIDE  
Warning: Be sure the SC101T power cord is  
unplugged before adding or removing the disks.  
Failure to observe this precaution could render your  
disks useless.  
Note: This software must be installed on each PC that will access the  
Storage Central Node.  
Storage Central SC101T  
The instructions below explain how to set up a single  
disk. Repeat these steps to install a second disk.  
Installation Overview  
1. Insert the NETGEAR CD into your PC. If this screen does not  
appear, run Autorun.exe on the CD. Click Install Software.  
Estimated Completion Time: 30 minutes.  
1. Remove the front cover.  
After you prepare for installation, these instructions will guide you through these three  
steps:  
1. Install a hard disk, and connect the Storage Central SC101T to your network.  
2. Install the Storage Central SC101T software.  
2. Insert a hard disk.  
Position the disk with the bottom  
facing in.  
3. Allocate SC101T disk space for each PC that will use the SC101T.  
When you finish the installation, your network will resemble this illustration.  
Slide the disk into either slot.  
Replace the front cover  
3. Connect the SC101T to your network.  
2. Click Check for Updates and proceed according to the prompts. The software checks  
to see if the SC101T is on your network. You can install the software even if the unit  
is not yet on your network. If Windows logo certification warnings appear, click  
Continue to proceed.  
Connect the provided Ethernet cable to your network  
and to the back of the SC101T. Be sure your network  
is running. DHCP must be available in the network.  
DHCP is usually enabled on home networks by  
default.  
3. Follow the New Hardware Found prompts to  
complete the installation of several software driver  
components. You will see the Storage Central  
Manager utility icon on your desktop.  
Preparing for Installation  
4. Turn on the SC101T  
You must have an SATA hard disk, an Ethernet network with an available port, DHCP  
must be running in the network, and you need to have either Windows XP (SP2) or  
Windows 2000 (SP4) PCs to access the SC101T.  
Plug in the power adapter to a power source  
and connect the other end to the SC101T. Turn  
the unit on. View the front panel to verify that  
the green power light is on and that the green  
network light is on.  
4. Run the Storage Central Manager, which can  
check for updates. Click Next to proceed, and.  
follow the prompts to check for and install  
additional product updates.  
Unpack the unit, Ethernet cable, power adapter, and the NETGEAR CD. The CD  
contains driver software, a setup wizard, and links to online resources. Familiarize  
yourself with the Storage Central SC101T unit. The back panel of the SC101T has  
information about the ports and the status lights located on the front panel.  
After the additional product updates process  
completes, you will see the Storage Central  
Manager configuration mode selection screen.  
When you set up the unit, stand it on its feet, and be sure it has ample ventilation.  
Avoid putting the unit in a location where it could be knocked over easily. Do not  
place items on top of it.  
 

Miele Refrigerator KWT 4974 SG ed User Manual
Multiquip Portable Generator GA 36RZ2 User Manual
Mustang Survival Life Jacket MD3188 User Manual
Nikon Projector NP2000 User Manual
Nikon Projector VT46 User Manual
Onkyo Stereo Receiver TXNR727 User Manual
Onkyo Stereo System M 282 User Manual
Pacific Digital Automobile PTV3606 User Manual
Palm Cell Phone Accessories 185 10441 00 User Manual
Panasonic Car Stereo System CQ DPX95EUC User Manual