NETGEAR Network Card GS116E 100NAS User Manual

Note: Contact your reseller or customer support in your area if there are any missing or  
damaged parts. You can refer to the Support Information Card for the telephone  
number of customer support in your area. You should keep the Support Information  
card, along with the original packing materials, and use the packing materials to  
repack the WAGL102 or WGL102 if you need to return it for repair.  
Make sure the Ethernet cable connectors (if used) are securely plugged in at the  
access point and the network device (hub, switch, or router).  
)NSTALLATION 'UIDE  
Make sure the connected device is turned on.  
ProSafe Light Wireless Access Point, WAGL102 or WGL102  
The WLAN lights are not lit.  
Disconnect the adapter from its power source and then plug it in again. Contact  
NETGEAR if the Wireless LAN lights remain off.  
2. Connect the access points directly to the WFS709TP ProSafe Smart Wireless Switch  
to configure them and to download firmware (for full instructions, see the  
documentation for the WFS709TP ProSafe Smart Wireless Switch).  
Start Here  
I cannot configure the access point from the WFS709TP ProSafe  
Smart Wireless Switch.  
3. Mount or place the access point where you intend to deploy it.  
4. Power the access point by one of these methods:  
This guide describes installation for the WAGL102 ProSafe™ 802.11a/g Dual Band Light  
Wireless Access Point or WGL102 Prosafe 802.11g Light Wireless Access Point.  
Check that the WAGL102 or WGL102 is properly installed, the LAN connections are  
OK, and that the LAN port LED is green. Check the operational status of the  
WFS709TP ProSafe Smart Wireless Switch.  
Note: The WAGL102 or WGL102 Light Wireless Access Points work only in conjunction  
with the WFS709TP ProSafe Smart Wireless Switch. In order to complete access point  
installation, the WFS709TP should be already configured and available on your network.  
For instructions on advanced configuration options for access points, please refer to the  
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual, which can  
be downloaded from http://www.netgear.com/support.  
Power adapter—connect to a power source using the supplied power adapter.  
PoE (power over Ethernet)—connect an Ethernet cable between the access  
point’s 65 FE Port and:  
Specifications  
-
-
A network port on a WFS709TP ProSafe Smart Wireless Switch, or  
A network mid-span device that supports a 802.3af compliant port.  
5. Orient the antenna (for best performance, a vertical position is recommended).  
6. Verify successful installation by observing the LED status:  
Parameter  
WAGL102 ProSafe 802.11a/g Dual Band Light Wireless Access Point  
or WGL102 Prosafe 802.11g Light Wireless Access Point  
Estimated Completion Time: 20 minutes.  
Maximum Clients  
Limited by the amount of wireless network traffic generated by each node;  
typically 15 to 20 nodes.  
Installing the Access Point  
LED  
Color(s)  
Activity  
Off  
Action  
Status LEDs  
Power/Ethernet LAN/Wireless LAN/Test  
12V DC, 1 A  
ENET (10/100 Mbps)  
Green  
No link  
Power Adapter  
1. Unpack the box and verify the contents, as follows:  
Green on  
Green flashing  
Off  
10/100Mbps link negotiated  
10/100Mbps data activity  
Wireless radio disabled  
Wireless radio AP mode enabled  
Wireless radio AM mode enabled  
Environmental  
Specifications  
Operating temperature: 0 to 50° C  
Operating humidity: 5-95%, non-condensing  
WAGL102 ProSafe 802.11a/g Dual Band Light Wireless Access Point or  
WGL102 Prosafe 802.11g Light Wireless Access Point  
WLAN LEDs  
Green  
Antenna  
WAGL102: One (1) external 5dBi 2.4 GHz detachable antenna and one (1)  
external 5 dBi 5GHz detachable antenna  
WGL102: One (1) external 5 dBi 2.4 GHz detachable antenna  
Antenna:  
Green on  
Green flashing  
-
-
WAGL102—one 2.4 GHz antenna and one 5 GHz antenna  
WGL102—one 2.4 GHz antenna  
Wireless LAN  
network  
standards  
IEEE 802.11a, IEEE 802.11b and IEEE 802.11g  
Wall mounting screws  
7. Complete your installation by defining the operational behavior for each access point  
in your network.  
Straight through Category 5 Ethernet cable  
Power adapter and cord (12 V dc, 1.2 A)  
Radio technology  
• 802.11b: 1 and 2 Mbps, Direct Sequence Spread Spectrum (DSSS)  
• 802.11b: 5.5 and 11 Mbps, Complementary Code Keying (CCK)  
• 802.11g: All rates, Orthogonal Frequency Division Multiplexing (OFDM)  
ProSafe Light Wireless Access Point, WAGL102 or WGL102 Installation Guide  
(this document)  
Troubleshooting Tips  
Radio modulation  
type  
• 802.11a - BPSK, QPSK,16-QAM, 64-QAM  
• 802.11b - CCK, BPSK, QPSK  
• 802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM  
Support Registration card  
Here are some tips for correcting simple problems you may have.  
No lights are lit on the access point.  
Media Access  
Control  
CSMA/CA with ACK  
Make sure the power is connected to the access point.  
 

Miglia Technology Satellite TV System Alchemy TV User Manual
Niles Audio Portable Speaker OS55 User Manual
Nilfisk ALTO Water Pump 7309021 User Manual
Nortel Networks Welding System P0919439 User Manual
Oki Network Card 310Eplus User Manual
Oregon Clock AWS888 User Manual
Panasonic Camcorder AJ D255MC User Manual
Panasonic Digital Camera AK HC930P User Manual
Panasonic DVD Player KX F790 User Manual
Panasonic Telephone KX G2200A User Manual