NEC Car Video System OL V552 User Manual

NEC Display Solutions of America, Inc.  
OL-V552 Installation Guide  
10 Point Touch Overlay for the V552  
Rev 1.0  
1.0  
Contents  
Guide Purpose  
Page 1  
Notes and Warnings  
Equipment  
Page 1  
Page 2  
Page 2  
Page 3  
Dimensional Drawings  
Integration Procedures  
2.0  
2.1  
3.0  
Purpose  
This procedure describes the steps to install the OL-V552 IR Touch Overlay onto the V552 display  
Notes and Warnings  
3.1  
3.2  
The overlay contains tempered glass. Use caution when handling.  
The overlay has an integrated USB cable located in the bottom right corner. Ensure the cable is not  
pinched, crushed, or damaged during installation.  
3.3  
3.4  
Installation requires two persons at all times to ensure the touch screen frame does not bend or torque.  
Once the touch screen is installed, do not lift the monitor by grasping or holding the touch screen  
overlay.  
3.5  
Contact NEC Display Solutions support if you have any questions or require additional installation  
guidance support.  
500 Park Boulevard, Suite 1100  
Itasca, IL 60143  
Phone: (800) 632-4662  
OL-V552  
1
 
NEC Display Solutions of America, Inc.  
OL-V552 Installation Guide  
10 Point Touch Overlay for the V552  
Rev 1.0  
6.0  
Integration Procedure  
6.1  
Place the display face up on a padded surface for overlay integration  
6.1.1 Note that if the unit is already mounted, removing the unit and placing it face up is optional;  
integration of the touch screen can also be done while the display is mounted  
6.2  
6.3  
Remove bottom right corner screw from the factory bezel as shown.  
Remove additional three (2) bottom screws; one located on the  
bottom far left corner and center of the factory bezel.  
6.4  
Remove three (3) screws located in the top of the factory bezel similar  
to the bottom screw removal in steps 6.2 and 6.3  
6.4.1 Note that only these six (6) screws should be removed. The  
other screws are used to keep the bezel secured to the body  
of the display  
6.5  
6.6  
Remove the IR touch screen overlay from packing and verify contents  
of kit parts.  
Clean inside surface of the glass.  
6.6.1 Use a glass cleaner or mild cleaning solution to clean glass.  
6.6.2 Spray solution onto clean soft cloth then wipe the surface. Spraying cleaning solution directly onto the  
monitor may damage the unit.  
6.6.3 Use circular motion to avoid smudges and streaks.  
6.6.4 DO NOT USE any chemical solvents such as an Acidic, or Alkali solution.  
With help from a partner, lift the touch frame on the side edges and place over the monitor.  
6.7  
6.8  
6.9  
Ensure the six (6) mounting holes on the touch screen overlay align with the screw holes of the monitor.  
Install the touch screen overlay using four (3) M3 x 30 flathead Phillips machine screws for the top side  
6.10 Install the touch screen overlay using four (3) M3 x 35 flathead Phillips machine screws for the top side  
6.11 Connect the touch screen USB cable to the PC / media player providing video to the display.  
6.12 Installation is complete.  
OL-V552  
3
 

Miele Cooktop KM 417 User Manual
Milwaukee Drill 4004 20A User Manual
Moulinex Microwave Oven AFW2 User Manual
NAD Stereo Receiver AV711 User Manual
Nokia Cell Phone 2160i User Manual
Omega Vehicle Security Stereo System OMWT DIPOLE 900 25 User Manual
Omnitron Systems Technology Network Card T3 E3 User Manual
Omron Healthcare Blood Pressure Monitor HEM 780 User Manual
Onkyo Stereo Receiver TX NR636 User Manual
Oregon Scientific Clock BA812E User Manual