Murphy Remote Starter AS730 User Manual

M011001  
R
Issue 4, revised 06/99  
The Generator Controls Division of  
Catalogue section 75  
(MS5261)  
AUTOSTART 730 (AS730 series)  
PROGRAMMABLE GENERATOR CONTROLLER  
The Autostart 730 provides for the fully automatic or manual  
control of a standby generator. The unit has similar control  
and instrumentation features to the Autostart 710, but with  
the addition of 3 phase generator voltage and current  
measurement, display and fault tripping.  
Key features  
·
Automatic, Manual and Program modes, selected by  
front facia push button keys  
·
·
32 character, back-lit liquid crystal display (LCD)  
Fully programmable generator control options, timers,  
inputs, outputs and fault protections  
Product Specification  
·
·
·
Monitoring, display and programmable fault trips for  
generator speed/frequency, 3 phase voltage and 3  
phase current with IDMT response.  
Power supply:  
Operating voltage: steady state range  
crank brown-out  
Current consumption  
Inputs:  
DC inputs:-  
5 – 40 V DC continuous  
to 0 V for >=100mS  
typically 200 mA  
Comprehensive automatic fault protection system:–  
up to 5 programmable fault inputs, overspeed, charge  
fail, emergency stop, and high and low battery volts  
6 programmable outputs, each with over 40 different  
function (or ‘action’) types.  
positive input defined as:  
negative input defined as:  
Input 1 (oil pressure) and  
Input 2 (engine temperature)  
80% to 100% of battery +ve  
–1V to +2V w.r.t. battery –ve  
switch (open or closed) or analogue  
(Murphy, Datcon, VDO 5 or 7 bar),  
wired to –ve DC  
Operation  
Control of the Autostart is via 4 front facia keys:-  
ON/MODE Turns on the Autostart and allows selection  
of Auto or Manual modes.  
Inputs 3 - 5  
switch (open or closed),  
wired to +ve or –ve DC  
PAGE  
Used to scroll through measured generator  
parameters, such as 3 phase voltage  
and current, engine oil pressure and  
Generator AC inputs:-  
operating voltage range  
gen. frequency measurement range  
gen. frequency display accuracy  
gen. frequency display resolution  
Magnetic pickup:  
90 – 300 V AC rms L–N  
0 – 99 Hz.  
<= 2% of full scale  
1 Hz.  
temperature, hours run and battery voltage.  
SELECT  
OFF  
Used in the programming of Autostart  
Turns the Autostart off, disabling the  
generator and resetting any fault condition.  
operating voltage range  
7 – 80 V AC rms  
0 – 10 kHz.  
<= 2% of full scale  
10 RPM  
frequency measurement range  
generator RPM display accuracy  
generator RPM display resolution  
AC current sensing inputs:  
operating range  
These keys are also labelled with  
symbols,  
used in the programming of each Autostart (see overleaf).  
Two front facia LEDs indicate the selected operating mode:  
green for Auto, amber for Manual.  
designed for use with 5 Amp CT's  
primary ratings 10 to 5000 Amps  
Control Outputs  
Outputs:  
(all ratings for resistive load)  
Dedicated relay outputs are used for engine fuel and starter  
motor control. The AS730 has 6 programmable outputs,  
each of which may be set up for use as one of over 40  
function types, e.g. preheat (4 types), engine running,  
individual faults (e.g. overspeed, overcurrent, start fail,  
oil pressure, etc.), energised to stop fuel, etc.  
Start and fuel relays  
SPNO contacts (switched +ve)  
rated 16 A max. @ 24 V DC  
– ve DC (open collector transistor)  
250 mA max. @ 33 V DC  
– ve DC (switched relay)  
5 A max. @ 24 V DC  
Programmable outputs 1 – 3  
Programmable output 4  
Fault Protection and Alarm System  
Programmable output 5  
(default setting: Common Alarm)  
Programmable output 6  
+ ve DC (switched relay)  
5 A max. @ 24 V DC  
volt free SPNO relay  
The Autostart 730 has a comprehensive fault detection,  
warning and automatic response system:-  
(default setting: Gen. Contactor)  
5 A max. @ 240 V AC  
·
Dedicated inputs for low oil pressure and high engine  
temperature sensors, either switch or analogue type.  
The use of analogue sensors allows for pre-warning as  
well as shutdown alarms, and real-time display of oil  
pressure and engine temperature.  
Physical:  
Overall dimensions (W x H x D)  
Panel cut-out size (W x H)  
Weight  
144 x 96 x 162 mm  
DIN standard 140 x 92 mm  
approx. 720 g  
–10 to +55 oC  
·
·
Three programmable inputs for use with remote fault  
switches. The inputs can be set to give a warning only,  
generator load release or shutdown response.  
Operating ambient temperature  
In order to consistently bring you the highest quality,  
full featured products, we reserve the right to change our  
specifications and designs at any time.  
User set trip levels and response for generator speed/  
frequency, 3 phase voltage and 3 phase current.  
 

Miele Dishwasher G 2143 User Manual
Miele Ventilation Hood DA 2210 User Manual
Mr Heater Fan MH24T User Manual
MTX Audio Speaker TXC41 User Manual
NordicTrack Treadmill NTL190070 User Manual
Omega Vehicle Security Air Conditioner DRN ACC User Manual
Optimus Car Speaker HTS 102 User Manual
Panasonic Computer Monitor BT LH80W User Manual
Panasonic Welder LX 200PX User Manual
ParaBody Fitness Equipment 837101 User Manual