Operating and Installation
Instructions
Ventilation System
DA 270-4
en - US, CA
To prevent accidents
and appliance damage,
read these instructions
before
installation or use.
M.-Nr. 07 260 851
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
READ AND SAVE THESE
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
INSTRUCTIONS
Keep these instructions in a safe
place and pass them on to any future
user.
OBSERVE THE FOLLOWING:
a) Use this appliance only in the
~
manner intended by the manufacturer.
Read these instructions carefully
before installing or using the
Ventilation System.
If you have questions, contact Miele.
b) Before servicing or cleaning the
~
appliance, switch power off at the
service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally. If
the service disconnecting means
cannot be locked, securely fasten a
prominent warning device, such as a
tag, to the service panel.
This appliance is intended for
~
residential use only. Use the appliance
only for its intended purpose.
This appliance complies with current
~
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
c) Be certain your appliance is
~
properly installed and grounded by a
,CAUTION
qualified technician.
For General Ventilating Use
Only. Do Not Use To Exhaust
Hazardous Or Explosive
Materials And Vapors.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician.
This appliance is designed to vent
~
cooking smoke and odors only.
This appliance is suitable for
~
installation above gas or electric
cooking surfaces.
This appliance is not designed for
~
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions installation in these
applications may be possible. Please
contact your Miele dealer or the Miele
Technical Service Department with
specific requirements.
3
IMPORTANT SAFETY INSTRUCTIONS
d) Before connecting the appliance
Use
~
to the power supply make sure that the
voltage and frequency listed on the
data plate correspond with the
household electrical supply.
,WARNING
TO REDUCE THE RISK OF A
COOKTOP GREASE FIRE:
This data must correspond to prevent
appliance damage. If in doubt consult a
qualified electrician.
a) Never leave surface units
~
unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
e) Installation work and repairs
~
should only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous.
b) Always turn the hood on when
~
cooking at a high heat.
c) Clean the ventilation hood
~
f) Only open the housing as
frequently. Grease should not be
allowed to accumulate on the fan or
filter.
~
described in the enclosed "Installation
diagram" and in the "Cleaning and care"
section of this manual. Under no
circumstances should any other parts
of the housing be opened. Tampering
with electrical connections or
d) Use the proper pan size. Always
~
use cookware appropriate for the size
of the cooking area.
components and mechanical parts is
highly dangerous to the user and can
cause operation faults.
e) Do not flambé or grill with an
~
open flame beneath the hood.
Flames could be drawn up into the
hood by the suction and the grease
filters may catch fire.
g) Before discarding an old
~
appliance, disconnect it from the power
supply and remove the power cord to
prevent hazards.
4
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
Do not allow children to play with or
~
operate the appliance or its controls.
Supervise its use by the elderly or
infirm.
TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE
EVENT OF A COOKTOP
GREASE FIRE, OBSERVE THE
FOLLOWING*:
Always turn on the hood when using
~
the cooktop to prevent damage from
condensation.
a) SMOTHER FLAMES with a close
~
fitting lid, cookie sheet, or metal tray
then turn off the burner.
Never operate gas burners without
~
cookware. Turn the burner off when not
in use. Adjust the burner so that the
flames do not extend beneath the
cookware. Do not overheat the
cookware, e.g. when using a wok. The
hood can be damaged due to
excessive heat from the burners and
the cookware.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
b) NEVER PICK UP A FLAMING
~
PAN - You may be burned.
c) DO NOT USE WATER, including
Do not use the hood without the
~
grease filters in place.
~
wet dishcloths or towels - a violent
steam explosion will result.
Do not use a steam cleaner to clean
~
d) Use a fire extinguisher ONLY if:
the hood. Steam could penetrate
electrical components and cause a
short circuit.
~
1) You have a class ABC
extinguisher, and you know how to
operate it.
2) The fire is small and contained in
the area where it started.
3) The fire department is being
called.
4)You can fight the fire with your
back to an exit.
*
Based on "Kitchen Firesafety Tips"
published by NAFTA
5
IMPORTANT SAFETY INSTRUCTIONS
Installation
g) Do not install this hood over
~
cooktops that burn solid fuel.
,WARNING
h) Provided a larger distance is not
~
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and the
bottom of the hood given in the
"Appliance dimensions" section of this
manual.
a) Installation work and electrical
~
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
If local building codes require a greater
safety distance, follow their
requirement.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
b) Sufficient air is needed for
~
combustion and exhausting of gases
through the flue (chimney of fuel
burning equipment to prevent back
drafting. Follow the heating equipment
manufacturer’s guideline and safety
standards such as those published by
the National Fire Protection Association
(NFPA) and the American Society for
Heating, Refrigeration and Air
i) Never connect an exhaust hood to
~
an active chimney, dryer vent, vent flue,
or room ventilating ductwork.
j) Seek professional advice before
~
connecting an exhaust hood vent to an
existing, inactive chimney or vent flue.
Conditioning Engineers (ASHRAE), and
the local code authorities.
k) Any fittings, sealant, or materials
~
used to install the ductwork must be
made of approved non-flammable
materials.
c) When cutting or drilling into the
~
wall or ceiling, do not damage electrical
wiring and other hidden utilities.
d) Ducted hoods must always be
~
vented to the outdoors.
,WARNING
TO REDUCE THE RISK OF
FIRE USE ONLY METAL
DUCTWORK.
e) Do not use this hood with any
~
solid-state speed control device.
f) Do not use an extension cord to
~
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance,
(e.g. danger of overheating).
6
Functional description
The ventilation hood works by air
extraction. The air is drawn in and
cleaned by the grease filter and
directed outside.
The hood comes equipped with a
non-return flap. This flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occur. When the hood is
turned on, the air pressure of the
exhaust fan automatically opens the
flap blowing the inside air and cooking
odors outside.
7
Guide to the Ventilation System
8
Guide to the Ventilation System
a Cover frame
l Grease filter button
The indicator next to the grease filter
button lights when the grease filter
needs to be cleaned.
b Chimney
c Control panel
d Indirect lighting
e Overhead lighting
f Grease filter
This button is also used:
– to reset the grease filter timer after
cleaning the grease filter (see
"Cleaning and Care").
– to show how long the grease filter
has been in use (see "Operation /
Grease filter timer").
g Indirect light button
– to change the number of hours
counted by the grease filter timer
(see "Operation / Reprogramming the
grease filter timer").
h Light button
This button turns the light on and off
and also dims the light.
The lighting can be used independently
of the fan.
i On/Off button
j Fan power level buttons
Four fan speed selection.
k Delayed Shut Down
This button activates the Delayed Shut
Down feature. The fan can be set to
turn off automatically after either 5 or
15 minutes.
9
Operation
Turning on the fan
Automatically switching back the
intensive power level
The intensive level "4" can be
programmed to automatically switch
back to level "3" after 10 minutes.
^ Press the On/Off button.
^ Turn the fan and the lights off.
The hood turns on to level 2 and the
indicator lights.
Selecting the power level
^ Press and hold the "Delay Shut down"
button for 10 secs. The first indicator
lights.
^ Press the following buttons one after
^ Use the "–/+" controls to select the
another,
desired power level.
+ = increases the fan speed
– = decreases the fan speed
Levels "1" to "3" (green indicators) are
usually sufficient for normal cooking.
– the right light button
Intensive setting
Level "4" (yellow indicator) should be
used for a short period when frying or
cooking food with a strong aroma.
– the "–" button, and
– the right light button again.
10
Operation
Fan performance
The maximum air flow capacity is
625 cfm. Factors such as narrow duct
diameter and bends will affect this
value.
If the power level indicators "1" and "4"
flash, the automatic switch back is not
activated.
Level 1 operates at 40% capacity
Level 2 operates at 60% capacity
Level 3 operates at 80% capacity
Level 4 operates at 100% capacity
^ To activate the automatic switch back
press the "+" button.
The power level indicators "1" and "4"
light continuously.
^ To deactivate press the "–" button.
^ To save the setting press the "Delay
Shut Down" button.
If the procedure is not stored within
4 minutes of programming, the hood
will automatically default to the "old"
data.
11
Operation
Delayed Shut Down
Turning off the fan
If odors or smoke remain in the kitchen
after cooking has been completed, the
Delayed Shut Down feature can be
selected to allow the hood to continue
running for either 5 or 15 minutes. After
that period of time the fan turns off
automatically.
^ Press the On/Off button to turn the
fan off.
The indicator goes out.
Automatic Safety Shut Off
The fan will turn off automatically
10 hours after the last button was
activated. The lighting however will
remain on.
^ Press the Delayed Shut Down button
while the fan is still running.
Press once = 5 minute delay
(left indicator lights)
Press twice = 15 minute delay
(right indicator lights)
^ Press the On/Off button to turn the
To cancel the feature press the
Delayed Shut Down button again. The
fan will not turn off automatically.
fan back on again.
12
Operation
Turning the lighting on/off
Indirect lighting
The overhead lighting can be turned on
and off independently of the fan.
^ Press the left light button to turn the
indirect lighting on or off.
^ Press the right light button briefly to
The indirect lighting can be turned on
and off independently of the fan.
turn on the lighting.
The light button indicator illuminates.
^ Press the right light button briefly
again to turn off the lighting.
The light button indicator will go out.
Dimming the lighting
The brightness of the lighting can be
adjusted.
^ While the lighting is turned on, press
and hold the light button.
The lighting will dim until the button is
released.
^ If the button is pressed again, the
lighting will brighten until the button is
released.
If the button is pressed continuously,
the light will cycle between bright and
dark.
^ Press the light button again to turn off
the lighting.
13
Operation
Grease filter timer
Checking the grease filter timer
A timer monitors the hours of fan
operation. The indicator for the grease
filter will light after 30 hours of operation
or the preselected time. The grease
filter must then be cleaned. See
To check the percentage of time
already used:
"Cleaning and care / Grease Filter".
^ Press the On/Off button to turn the
After the grease filter has been cleaned
and put back in place, the grease filter
timer must be reset.
fan on.
^ Press the grease filter button.
^ To do this, press the grease filter
button for about 3 seconds while the
fan is running.
The indicator lights.
The indicator will go out.
The number of flashing "–/+" indicators
show the percentage of programmed
hours that have been used.
1 indicator = 25 %
2 indicators = 50 %
3 indicators = 75 %
4 indicators = 100 %
This information will remain stored in
memory in the event of a power failure.
14
Operation
Reprogramming the grease filter
timer
The grease filter timer is preset to
30 hours. This time can be lengthened
or shortened to 20, 30, 40 or 50 hours.
The lit "–/+" indicator shows the
programmed time:
– A time of 20 hours should be
programmed in kitchens with
frequent pan or deep frying.
1st indicator from the left = 20 hours
2nd indicator from the left = 30 hours
3rd indicator from the left = 40 hours
4th indicator from the left = 50 hours
– A time of 20 hours should also be
programmed if the kitchen is only
used occasionally to prevent grease
which has accumulated over a long
period of time from hardening on the
filter, making cleaning more difficult.
^ Use the "–/+" button to select the
desired time.
^ Store the selection by pressing the
grease filter button.
^ Press the On/Off button to turn off the
If the procedure is not stored within
4 minutes of programming the hood
will automatically default to the "old"
data.
fan.
^ Press the Delayed Shut Down and
grease filter button at the same time.
The indicator for the grease filter timer
and one of the "–/+" indicators will flash.
15
Cleaning and care
,WARNING
Avoid:
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
– cleaning agents containing soda,
acids or chlorides,
– abrasive cleaning agents
e.g. powder or cream cleansers,
– abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents.
Before cleaning or servicing the
hood, disconnect it from the power
supply, see "Important Safety
Instructions".
These will damage the surface.
Cleaning the casing
The following instructions for cleaning
"Stainless steel" surfaces and "Stainless
steel colored controls" should be
followed in addition to the general
"Cleaning the casing" instructions.
Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
will damage the surface.
Stainless steel
^ The exterior surfaces and controls
can be cleaned with a mild solution
of warm water and liquid dish soap
applied with a soft sponge.
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
^ Wipe dry using a soft cloth.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Only use a slightly damp sponge
when cleaning the controls. Water
could penetrate into the electronics
and cause damage.
Stainless steel colored controls
These controls may become dis-
colored or damaged if not cleaned
regularly.
^ Glass surfaces can be cleaned using
glass cleaner.
Do not use a stainless steel cleaner
on these controls.
16
Cleaning and care
Grease filter
Removing the grease filter
The reusable metal grease filter
removes solid particles from the vented
kitchen air (grease, dust, etc).
The grease filter should be cleaned
every 3 - 4 weeks, when the grease
filter indicator lights, or when they are
visibly dirty, whichever comes first.
^ To remove the grease filter pull the
locking clip forward. Lower the filter
45° unhook it at the rear and take it
out. Support the grease filter so that it
does not fall onto the cooktop.
,A dirty filter is a fire hazard.
17
Cleaning and care
Cleaning the grease filter
^ By hand: use a scrub brush with a
solution of warm water and mild
detergent.
Do not use the pure detergent,
aggressive all purpose cleaners,
oven sprays, abrasive cleaning
agents or limescale removers. They
could destroy the filter.
^ If the filter is incorrectly installed,
insert a small screwdriver into the slit
along its edge to disengage it from
the casing.
^ In a dishwasher: place the filter
vertically in the lower basket, making
sure that the spray arm is not
blocked.
Use a hot temperature program,
e.g. "Heavy Soil" or "Pots and pans".
Use the recommended amount of
dishwasher detergent. Overuse could
destroy the filter.
^ After returning the grease filter, press
the grease filter button for 3 seconds
to reset the timer.
Depending on the detergent,
cleaning the grease filter in a
dishwasher may cause permanent
discoloration of the filter surface.
Performance of the filter will not be
affected by this discoloration.
The indicator light will go out.
^ If the grease filter is cleaned before
the grease filter timer has reached its
maximum, the grease filter button
should be pressed for 6 seconds to
reset the counter to zero.
^ After cleaning, the filter can be
placed on a towel to air dry.
^ While the filter is removed, clean any
dirt or grease from the interior casing
to prevent the risk of fire.
^ When putting the grease filter back
make sure that the locking clip is
facing the cooking surface.
18
Cleaning and care
Changing the light bulbs
,WARNING
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Before changing the light bulbs,
disconnect the hood from the power
supply, see "Important Safety
Instructions".
When in use halogen bulbs become
extremely hot, and can burn your
hands. Do not attempt to change the
bulbs until they have had sufficient
time to cool.
^ To change the halogen bulb, first
gently press the light cover. The
cover will open and can now be
flipped down.
Do not touch the bulb surface.
Fingerprints or body oils deposited
on the bulb will decrease its life.
Please follow the manufacturer’s
instructions.
^ Pull the halogen bulb from its socket,
then insert a new bulb.
^ Flip the light cover back up, making
sure it clicks into place.
19
After Sales Service
Repairs
MieleCare
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department.
(USA only)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
^ When contacting the Technical
Service Department, please quote
the model and serial number of your
appliance.
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
These are shown on the data plate
which is visible when the grease filters
are removed.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
20
Installation Instructions
Read these instructions and the
"Important Safety Instructions"
before installing this hood.
22
Caring for the environment
Disposal of packing material
Disposal of an old appliance
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old appliance,
disconnect it from the electrical
,DANGER
Ensure that any plastic wrappings,
bags, etc., are disposed of safely
and kept out of the reach of babies
and young children. Danger of
suffocation!
supply and cut off the power cord to
prevent it from becoming a hazard.
23
Appliance dimensions
Exhaust connection 6" (150 mm) diameter
1) Opening for ductwork and power cord
24
Appliance dimensions
Distance between cooktop and
hood (S)
Be sure to follow the minimum safety
distances given by the gas cooktop
manufacturer to easily flammable
materials e.g. upper cabinets.
Do not install this exhaust hood over
cooktops burning solid fuel.
If local building codes require a
greater safety distance, follow their
requirement.
Provided a larger distance is not
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and
the bottom of the hood:
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
Miele cooktops:
- 24" (610 mm) above electric
surfaces,
- 26" (660 mm) above electric
grill/boiler/fryers,
See "Important Safety Instructions"
for further information.
- 24" (610 mm) above gas surfaces
ß 25,000 BTU's (7.5 kW) and no
burner greater than 10,250 BTU's
(3 kW) ,
- 30" (762 mm) above gas surfaces
> 25,000 BTU's (7.5 kW),
- 30" (762 mm) above burner heads
> 10,250 BTU's (3 kW). For
example, a Wok used separately
or in combination with a cooktop.
Non-Miele cooktops:
- 24" (610 mm) above all electric
surfaces,
- 30" (762 mm) above all gas
surfaces,
- 26" (660 mm) above electric
grill/boiler/fryers.
If several gas surfaces are installed
under the hood, the total output must
be considered when determining the
minimum safety distance.
25
Structural support
The ceiling mounting plate will
support the weight of the hood. This
ceiling plate must be attached to
rigid structural framing that is
supported in its entirety by the
ceiling joists, or to the ceiling joists
directly. Do not attach the plate
directly to the ceiling with anchors,
toggle bolts, etc.
,CAUTION
When cutting or drilling into the wall
or ceiling, do not damage electrical
wiring and other hidden utilities.
26
Installation
Installation instructions
Installation accessories
^ See the enclosed installation
instruction diagram.
^ Please read the "Important Safety
Instructions" and Installation
instructions before installing this
hood.
4 Screws 8 x 60 mm with 4 Washers
for securing the ceiling plate.
(S8 wall anchors included in the
packaging are not for use in USA)
Protective film
The casing is covered with a protective
film to prevent scratching during
transport.
^ Peel off the film before installing the
casing parts.
2 Screws M 4 x 8 mm
for adjusting the chimney.
,CAUTION
To avoid risk of hand or other injury,
avoid contact with sharp edges
during the assembly and installation
process.
4 leveling plates
for correcting an uneven ceiling.
1 exhaust connector
1 hose clip for securing the ducting.
27
Air extraction
Exhaust ducting and connections
,WARNING
– The ducting should be as short and
straight as possible, and the number
of sharp bends should be minimized.
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
To reduce the risk of fire and to
properly exhaust air, the exhaust
gases extracted by the hood
should be vented outside of the
building only.
– For most efficient air extraction, the
diameter of the ductwork should not
be less than 6" (150 mm). Use of flat
ducts also reduces the air extraction
efficiency.
– Noise levels of the hood will increase
if flat ducts or round ducts of less
than 6" (150 mm) in diameter are
used.
Do not vent exhaust air into
– Use smooth or flexible pipes made
from approved non-flammable
materials for exhaust ducting.
spaces within walls or ceilings or
in attics, crawl spaces, or garages
To reduce the risk of fire, only use
metal ductwork.
– Where the ductwork is horizontal, it
must slope away from the hood at
least 1/8" per foot (1 cm per meter) to
prevent condensation dripping into
the appliance.
Please read and follow the
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk of
personal injury. Follow all local building
codes when installing the hood.
– If the exhaust is ducted through an
outside wall, a Miele Telescopic Wall
Vent can be used.
28
Air extraction
Condensate trap
optional accessory
In some cases, a condensate trap may
be required to collect and evaporate
any condensation which may develop.
This optional accessory is available for
ducts 5" (125 mm) and 6" (150 mm) in
diameter.
– If the exhaust is ducted into an
inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Never connect an exhaust hood to
an active chimney, dryer vent, flue,
or room venting ductwork. Seek
professional advice before
connecting an exhaust hood vent to
an existing, inactive chimney or vent
flue.
^ When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust outlet.
Important
If the ductwork runs through rooms,
ceilings, garages, etc. where
temperature variations exist, it may
need to be insulated to reduce
condensation.
29
Electrical connection
,WARNING
Important
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
To increase security before the
machine is installed, it is
recommended to install a protective
switch (30 mA).
All electrical work should be
performed by a qualified electrician
in strict accordance with national
regulations (for USA: ANSI-NFPA 70)
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Important
The hood must be hard wired
accordingly:
Black/Red wire:. . . . connect to L1 (live)
White wire: . . . . . connect to N (neutral)
Green wire: . . connect to GND (ground)
Ensure that power to the appliance
is off while installation or repair work
is performed.
^ Verify that the voltage, load and
circuit rating information found on the
data plate (located behind the
grease filter), match the household
electrical supply before installing the
hood.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s
Technical Service Department. See
back cover for contact information.
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
30
Technical data
Maximum load. . . . . . . . . . . . . . . 450 W
Fan. . . . . . . . . . . . . . . . . . . . . . . 350 W
Lighting . . . . . . . . . . . . . . . . . 4 x 20 W
Indirect lighting . . . . . . . . . . . 2 x 10 W
Voltage . . . . . . . . . . . . . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Circuit rating. . . . . . . . . . . . . . . . . . 15 A
Weight . . . . . . . . . . . . . 82.7 lb (37.5 kg)
31
Alteration rights reserved / 1009
M.-Nr. 07 260 851 / 00
For the most updated manual see the Miele web site.
|