Miele Cooktop KM 6310 User Manual

Operating and Installation instructions  
Ceramic Cooktop with induction  
KM 6310  
KM 6344  
en - CA  
To prevent accidents and  
appliance damage,  
read these instructions  
before  
installation or use.  
M.-Nr. 09 166 590  
 
Safety instructions for installation  
Clearance above the cooktop  
If there is more than one appliance  
installed below the exhaust hood,  
each with a different safety  
clearance, the largest clearance  
must be used.  
For an exhaust hood above the  
cooktop, always use the clearance  
specified by the hood manufacturer.  
If there are no specifications from the  
hood manufacturer or if flammable  
materials (e.g. a utensil rail) are  
installed above the cooktop, the  
clearance must be at least 760 mm.  
61  
 
62  
 
Safety instructions for installation  
Minimum clearance underneath the  
Protective base  
cooktop  
Installation of a protective base under  
the cooktop is allowed but not required.  
To ensure proper ventilation of the  
cooktop, a minimum clearance is  
required between the appliance and an  
oven, protective base, or drawer.  
A gap of 10 mm at the back is required  
for the power supply cable.  
For better cooling of the cooktop, we  
recommend a gap of 20 mm at the  
front.  
The minimum clearance from the  
bottom of the cooktop to  
– the top of the oven must be 15 mm.  
– the top of the protective base must  
be 15 mm.  
– bottom of the drawer must be 75  
mm.  
63  
 
Safety instructions for installation  
Safety clearance to a wall covering  
A safety clearance must be maintained between the countertop cut-out and any  
wall covering to protect it from heat damage.  
If the covering is made of a combustible material (e.g. wood), a safety clearance  
e of 50 mm must be maintained between the cut-out and the covering.  
If the covering is made of a non-combustible material (e.g. metal, natural stone,  
ceramic tiles), a minimum safety clearance e of 50 mm less the thickness of the  
covering must be maintained between the cut-out and the covering.  
Example: 15 mm wall covering  
50 mm - 15 mm = 35 mm minimum clearance  
Flush-fitted cooktops  
Cooktops with frame or bevelled edges  
aMasonry  
bWall covering  
Dimension X = thickness of wall covering  
cCountertop  
dCut-out in the countertop  
dMinimum safety clearance  
for combustible materials is 50 mm  
for non-combustible materials is 50 mm less dimension X  
64  
 
Safety instructions for installation  
Cooktops with frame or  
bevelled edges  
Tiled countertop  
Seal between cooktop and  
countertop  
The grouting a and the hatched area  
below the cooktop frame must be  
smooth and flat, so that the frame will  
be level and the sealing strip under the  
edge of the upper part of the cooktop  
can provide an adequate seal against  
the countertop.  
The sealing strip under the edge of the  
upper part of the cooktop provides an  
adequate seal against the countertop.  
The cooktop must not be sealed with  
joint sealant (e.g. silicone).  
Cooktop and countertop could get  
damaged if the cooktop needs to be  
removed.  
65  
 
Installation dimensions  
KM 6310  
aFront  
bCooktop height  
cConnection for Miele|home  
dElectrical box  
The connection cable (1440 mm long) comes with the cooktop.  
66  
 
Installation dimensions  
KM 6344  
aFront  
bCooktop height  
cConnection for Miele|home  
dElectrical box  
The connection cable (1440 mm long) comes with the cooktop.  
67  
 
Installation  
Preparing the countertop  
Inserting the cooktop  
^ For the countertop cut-out use the  
dimensions given in the illustration.  
Observe the safety clearances (see  
Safety instructions for installation).  
^ Feed the power supply cable down  
through the countertop cut-out.  
^ Center the cooktop in the cut-out.  
Make sure that the seal under the  
cooktop sits flush with the countertop  
on all sides. This is important to  
ensure an effective seal.  
^ Seal the cut surfaces with a suitable  
heat-resistant sealant to avoid  
swelling caused by moisture.  
NEVER apply an additional sealant  
such as silicone!  
Ensure that the sealant does not get  
on the top surface of the countertop.  
If the seal at the corners does not lie  
flush on the worktop, the corner radii  
ß R4 should be re-worked with a  
jigsaw.  
This cooktop has a seal underneath  
to keep it securely in position. Spring  
clips are not required.  
^ Connect the cooktop to the electrical  
The gap between the frame and the  
countertop will get smaller over time.  
power supply.  
^ Check that the cooktop is working  
^ Follow the instructions in the wiring  
properly.  
diagram (see Electrical connection).  
68  
 
Electrical connection  
Connection  
,CAUTION: Before installation or  
servicing, disconnect the power  
supply by either removing the fuses,  
shutting off the power main or  
manually "tripping" the circuit  
breakers.  
The cooktop is ready for connection to  
a grounded power supply.  
208/240 V, 60 Hz, 40 A fuse rating.  
Connect as following:  
Black wire: connect to L1 (hot)  
Red wire: connect to L2 (hot)  
Green wire: connect to GND (ground)  
Installation work and repairs should  
only be performed by a qualified  
technician in accordance with all  
applicable codes and standards.  
Repairs and service by unqualified  
persons could be dangerous and  
the manufacturer will not be held  
responsible.  
Before connecting the appliance to  
the power supply, make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This  
data must correspond to prevent  
appliance damage. Consult an  
electrician if in doubt.  
A dedicated line and junction box  
should be used to connect the cooktop  
to a 40 A circuit.  
For further information, see the wiring  
diagram provided with the appliance.  
, WARNING:  
THIS APPLIANCE MUST BE  
GROUNDED!  
Only operate the cooktop after it has  
been installed into the countertop.  
Connecting the electrical supply  
cable  
Installer:  
Please leave these instructions with  
the consumer.  
The electric power supply cable  
must be connected to the cooktop  
by a qualified electrician.  
Power supply  
^ Make sure your electrical supply  
matches the data plate.  
69  
 
Technical Service, Data plate  
In the event of a fault which you cannot easily fix yourself, please contact the  
Miele Technical Service Department at the address on the back of this booklet.  
When contacting Technical Service please quote the serial number and model of  
the appliance. This information is visible on the silver data plate supplied with the  
appliance.  
Adhere the included data plate and make sure the model designation matches up  
details on the cover page of this manual.  
70  
 
71  
 
Alteration rights reserved / 3313  
M.-Nr. 09 166 590 / 03  
For the most updated manual, visit the Miele web site.  
 

Miller Electric Welder XMT 4 Rack User Manual
Multiquip Portable Generator DCA125USI User Manual
Nortel Networks Switch 5399 User Manual
Olfa Gas Grill 720 0430 User Manual
Omron Building Set hja 306 User Manual
Oster Toaster Oster User Manual
Panasonic Portable Multimedia Player FZ 35S User Manual
Panasonic Security Camera GP KS822CU User Manual
ParaBody Home Gym 893102 User Manual
Paragon Radar Detector PY60 User Manual