Miele Cooktop KM 5753 User Manual

Operating and Installation  
Instructions  
Ceramic Cooktop with Induction  
KM 5753  
KM 5758  
en - US, CA  
To prevent accidents and  
appliance damage,  
read these instructions  
before  
installation or use.  
M.-Nr. 06 766 201  
 
Contents  
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Technical Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Installation dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Installing the cooktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Help protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
READ THE OPERATING  
INSTRUCTIONS CAREFULLY  
BEFORE USING THE  
COOKTOP  
Installation  
Be certain your appliance is  
~
properly installed and grounded by a  
qualified technician in accordance with  
national and local safety regulations.  
WARNING -  
Do not connect the appliance to the  
~
main electrical supply using an  
extension cord. Extension cords do not  
meet the safety requirements of this  
appliance.  
This appliance is intended for  
residential cooking only.  
When using your appliance follow  
basic safety precautions including  
the following:  
Before servicing, disconnect the  
~
appliance from the main power supply.  
To guarantee the electrical safety of  
~
this appliance, continuity must exist  
between the appliance and an effective  
grounding system. It is imperative that  
this basic safety requirement be met. If  
there is any doubt, have the electrical  
system of the house checked by a  
qualified electrician.  
Only for frame/facet cooktops:  
~
A small gap will be visible between  
cooktop and countertop for the first  
days after installation. The gap will  
decrease as the cooktop is used. The  
electrical safety of your appliance is  
warrantied despite the small gap.  
4
 
IMPORTANT SAFETY INSTRUCTIONS  
Use  
Do not use the appliance until it has  
been properly installed in the  
countertop.  
~
Only use the cooktop for residential  
~
cooking, and for the purposes  
described in this manual.  
Other uses are not permitted and can  
be dangerous.  
This appliance is equipped with an  
~
overheating protection feature. See  
"Overheating protection" for more  
information.  
Persons who lack physical, sensory  
~
or mental abilities, or experience with  
the appliance should not use it without  
supervision or instruction by a  
responsible person.  
Be sure to use the proper type of  
~
cookware. Follow the manufacturer's  
instructions.  
Never heat up empty pans. This  
~
could damage the appliance and  
cookware.  
Individuals with a pacemaker or  
~
similar medical device: Please note  
that an electromagnetic field develops  
when the cooktop is turned on.  
If the cooktop is installed above a  
~
pyrolytic oven it should not be used  
during the pyrolytic process. The  
overheating protection feature of the  
cooktop might be activated.  
Although unlikely that this will affect a  
pacemaker or other medical device,  
please consult the device manufacturer  
or your doctor if you have concerns.  
Keep magnetized items, e.g. credit  
~
cards, disks, etc. away from the  
cooktop while in operation. Damage  
may result.  
5
 
IMPORTANT SAFETY INSTRUCTIONS  
Injury prevention  
Be aware of loose fitting or hanging  
clothing when operating the cooktop,  
they may present a fire hazard.  
~
Children should not be left  
~
unattended in an area where the  
cooktop is in use. Never allow children  
to sit or stand on any part of the  
cooktop.  
Pot and pan handles should be  
~
turned inward and not extend over the  
countertop to reduce the risk of burns,  
ignition of flammable materials, and  
spills.  
Caution: Do not store items of interest  
to children in cabinets above the  
cooktop. Children climbing on the  
cooktop to reach these items could be  
injured.  
Never leave a cooktop unattended  
~
at high settings or when cooking with oil  
or fat. Overheated oil could ignite.  
Use the Child Safety Lock to prevent Always heat oil slowly, monitoring it as it  
children from turning on the burners or  
~
heats.  
changing the settings. See "Child  
Safety lock" for more information.  
Do not use water on grease fires.  
~
Smother or use a dry chemical or  
Keep all pots and pans out of  
children's reach. Danger of burning or  
scalding.  
foam-type extinguisher on any fire or  
flame.  
~
When frying food make sure that the  
~
food is as dry as possible before  
The appliance gets hot when in use  
and remains hot for quite a while after  
~
placing it in oil. Moisture can cause hot  
being turned off. As long as the surface oil to splatter and boil over. At high  
temperature is high enough to cause a  
burn, the Residual Heat Indicator will  
remain lit. Once sufficient time has  
passed and the cooktop surface is safe  
to touch, the Residual Heat Indicator  
will go out.  
settings, be cautious of splattering  
grease or boiling over liquids which  
may produce smoke.  
Do not flambé under an exhaust  
~
hood. Flames could be drawn up into  
the hood by the suction and the grease  
filters may ignite.  
Protect your hands with insulated  
~
gloves or potholders when using the  
appliance. Use only dry, heat resistant  
potholders. Moist or damp potholders  
used on hot surfaces can result in  
steam burns. Do not let the potholder  
touch the hot heating elements. Do not  
use towels or other bulky items near the  
appliance.  
6
 
IMPORTANT SAFETY INSTRUCTIONS  
Do not heat unopened containers.  
~
Built-up pressure may cause the  
Flammable materials should not be  
~
stored on or near the appliance.  
container to burst and result in injury.  
The cooktop is fitted with a cooling  
~
Before removing pots and pans be  
~
sure to turn off the burners.  
fan. Drawers under the cooktop are not  
recommended. If a drawer is fitted  
directly underneath the cooktop, ensure  
that there is sufficient space between  
the drawer, its contents and the  
underside of the appliance in order to  
ensure sufficient ventilation for the  
cooktop. Do not store small items or  
To prevent burns and breathing  
~
difficulty, allow the cooktop to cool  
before cleaning. Some cleaners may  
produce toxic fumes if applied to a hot  
surface.  
When wiping spills on a hot cooktop paper in the drawer. They could get  
sucked into the housing by the fan and  
cause damage or impair cooling.  
~
with a wet sponge or cloth, be careful  
to avoid steam burns.  
Ensure that no aerosols, combustible  
liquids or other flammable materials are  
kept in this drawer. If cutlery inserts are  
to be placed in the drawer they must be  
made of heat-resistant material.  
Do not let flammable materials,  
i.e. cooking grease, accumulate on the  
appliance.  
~
Never cover the cooktop with a  
~
cloth. A fire may result.  
Do not place items other than pots  
~
and pans on the cooktop.  
7
 
IMPORTANT SAFETY INSTRUCTIONS  
Damage protection  
Any spills should be removed as  
quickly as possible to prevent them  
from burning on and becoming difficult  
to remove.  
~
Never place hot pots or pans on the  
~
touch controls, this may damage the  
electronics.  
Do not use a steam cleaner to clean  
~
Do not drop anything on the ceramic  
surface of the cooktop. Even  
lightweight objects may cause damage.  
~
this appliance. Steam could penetrate  
electrical components and cause a  
short circuit.  
Do not use pots or pans with  
~
pronounced edges or ridges on the  
ceramic cooktop. These could scratch  
the cooktop permanently. See  
"Cookware" for more information. Grains  
of salt and sand can cause scratches.  
Make sure that the bases of any pots  
and pans are clean, free of any fat or  
oils, and are dry.  
Do not allow solid or liquid sugar,  
~
pieces of plastic or foil to fall on the  
burners when they are hot. If these  
residues are allowed to cool on the  
ceramic surface pitting or even  
cracking may occur.  
8
 
IMPORTANT SAFETY INSTRUCTIONS  
Appliance safety  
Further safety notes  
In the event of any damage to the  
appliance, it must be turned off  
immediately and disconnected from the contact with the cooktop. The insulation  
Make certain that the power cords of  
small appliances do not come in  
~
~
main power supply. Contact Miele’s  
Technical Service Department.  
Do not use the appliance until it has  
been repaired. Ensure power is not  
supplied to the appliance until repair  
work is completed.  
of the cable could become damaged.  
Danger of electric shock!  
Keep pets away from the cooktop at  
~
all times and activate the Safety Lock. If  
a pet gets on the cooktop a touch  
control sensor could be activated  
Do not cook on a damaged cooktop. turning on a burner.  
~
Any breakages or cracks in the ceramic  
surface of the appliance are defects  
and must be treated as such. If the  
cooktop should break, cleaning  
SAVE THESE INSTRUCTIONS  
AND REVIEW THEM  
PERIODICALLY  
solutions and spills may penetrate the  
broken cooktop and create a risk of  
electric shock. Do not use the  
appliance until it has been repaired.  
Repairs should only be performed  
~
by qualified technicians to ensure  
safety. Repairs and other work by  
unqualified persons could be  
dangerous. Do not open the outer  
casing of the appliance under any  
circumstances.  
While the appliance is under  
~
warranty repairs should only be  
performed by an authorized service  
technician. Otherwise the warranty is  
void.  
9
 
Guide to the cooktop  
Cooktop  
aBurner with double booster  
bcd Burners with single booster  
eBurner controls and displays  
fTimer controls and display  
gChild safety lock indicator  
hChild safety lock control  
iCooktop On/Off control  
jCooktop "On" indicator  
10  
 
Guide to the cooktop  
Burner controls and displays  
aPower level touch controls  
bBurner On/Off touch controls  
cBooster indicator  
dIndicator for "Auto heat" or extended  
power level (see "Programming"),  
e.g. front left burner  
eDisplays:  
-
= Burner is ready for use  
= Burner is turned on  
0
1 to 9 = Power level  
#
= Residual heat  
= No pan on burner or pan  
ß
unsuitable (see "Induction - How it  
works")  
I
= Single booster function  
activated  
II  
= Double booster function  
activated (only front left burner)  
F
= Fault (see "Safety cut-out  
feature")  
A
= Auto-heat with extended  
power level  
P0 etc. = Program (see  
"Programming")  
S0 etc. = Status (see  
"Programming")  
11  
 
Guide to the cooktop  
Timer control and display  
aTouch control to:  
- turn the timer on/off,  
- switch between functions, and  
- select a burner for "automatic switch-off".  
bTouch control for setting the time  
cTime display  
dAutomatic switch-off indicator  
eTimer indicator  
Burner data  
min to max  
diameter *  
Rating in watts  
208 V**  
Burner  
240 V**  
7" - 11"  
normal:  
2200  
2700  
3350  
2500  
3100  
3850  
y
(18 cm - 28 cm) with booster 1:  
with booster 2:  
4" - 7 " normal:  
(10 cm - 16 cm) with booster:  
1250  
1650  
1450  
1900  
w
x
z
5 ½" - 8" normal:  
(14 cm - 20 cm) with booster:  
5 ½" - 8" normal:  
1700  
2250  
1950  
2600  
1700  
2250  
1950  
2600  
(14 cm - 20 cm) with booster:  
Total:  
6700  
7700  
* Pans with a base diameter within the given range may be used.  
** The wattage quoted may vary depending on the size and material of the pans  
used.  
12  
 
Induction  
How it works  
If a suitable pan is placed on the burner  
within 3 minutes, the ß will go out and  
you can continue cooking as normal.  
An induction coil is located under each  
burner. When a burner is switched on,  
this coil creates a magnetic field which  
impacts directly on the base of the pan  
and heats it up. The burner itself is  
heated indirectly by the heat given off  
by the pan.  
If no pan or an unsuitable pan is placed  
on the burner, the burner and the  
cooktop will switch off automatically  
after 3 minutes.  
Be careful not to place cutlery or  
other metal objects on the cooktop.  
When the appliance is switched on,  
or when there is residual heat  
present, there is the risk of metal  
objects heating up quickly.  
Induction burners only work when a  
magnetic based pan is placed on it  
(see "Cookware").  
Induction automatically recognizes the  
size of the pan, i.e. heat is only  
generated in the area covered by the  
base of the pan.  
Beware of burns.  
Depending on the material, other  
objects left on the cooktop could  
also melt or catch fire. Switch the  
burners off after use.  
The burner will not work:  
– if it is switched on without a pan in  
place, or if the pan is unsuitable  
(non-magnetic base).  
– if the diameter of the pan is too small.  
– if the pan is taken off the burner  
when it is switched on.  
If this happens, ß will flash in the  
relevant burner display alternating with  
0 or the last selected power level  
selected.  
13  
 
Induction  
Noises  
The appliance has a cooling fan to help  
extend the life of the electronics. When  
the cooktop is being used at high levels  
for a long period of time, this will come  
on and you will hear a whirring sound.  
The fan may continue to run after the  
appliance has been switched off.  
When using an induction burner, the  
following noises can occur in the pan,  
depending on what it is made of and  
how it is constructed.  
– Higher power settings may cause a  
buzz. This will decrease or cease  
altogether when the power setting is  
reduced.  
– If the pan base is made of layers of  
different materials (e.g. a  
sandwiched base), a cracking sound  
may be heard.  
– Whistling might occur if linked  
burners (see "Booster function") are  
being used on the highest setting at  
the same time, and the pans have  
bases made of layers of different  
materials.  
– You may hear a clicking sound from  
the electronic switches, especially on  
lower settings.  
14  
 
Induction  
Cookware  
Pan size  
Suitable pans include:  
To make optimum use of the burners,  
choose cookware that fits between the  
inner and outer marking of the burner. If  
the base diameter of the pan is smaller  
than the inner marking, the induction  
heating will not work. The burner will  
behave as if it had no pan on it.  
– stainless steel pans with a magnetic  
base  
– enameled steel pans  
– cast iron pans  
Unsuitable pans:  
– stainless steel pans without a  
magnetic base  
– aluminum and copper pans  
– glass, ceramic or earthenware pots  
and pans  
To test whether a pot or pan is suitable  
for use on an induction cooktop, hold a  
magnet to the base of the pan. If the  
magnet sticks, the pan is suitable.  
Unless the pan manufacturer states  
that you can do so, do not use pans  
with very thin bases on this cooktop.  
,Never heat up empty pans.  
This could damage the appliance  
and cookware.  
15  
 
Before using for the first time  
Clean the cooktop  
Heat the cooktop  
^ Before using for the first time, clean  
the appliance with a damp cloth and  
dry with a soft cloth.  
Metal components of the cooktop have  
a protective coating which may give off  
a slight odor the first time the appliance  
is heated.  
The smell will dissipate after a short  
time and does not indicate a faulty  
connection or appliance defect.  
16  
 
Use  
Touch controls  
Turning on the cooktop  
The control panel on your ceramic  
cooktop is equipped with electronic  
sensors. They respond to a finger  
touch.  
To operate the burners, simply touch  
the corresponding sensor area(s). Each You will see a dash - in each of the  
^ Put a pot or pan on the desired  
burner.  
^ Touch the ON/OFF "s" cooktop  
touch control.  
time a command is registered, a signal  
will be heard.  
burner displays, and the On/Off  
indicator will light. If a setting is not  
chosen within a few seconds the  
cooktop will turn itself off as a safety  
measure.  
Be sure to touch only the desired  
sensor area and keep the control  
panel clean and clear. Otherwise,  
the touch controls may not respond,  
or unintentional commands may be  
given, even causing the cooktop to  
switch off automatically (see the  
section on "Safety cut-out feature").  
NEVER place hot cookware on the  
sensor areas. The electronics can  
be damaged.  
Turning on a burner  
^ Touch the s On/Off touch control for  
the desired burner.  
The respective burner display shows 0.  
^ Select a power level between 1 and 9  
by pressing the + or - control.  
When turning on the cooktop you can  
decide whether you want to cook with  
auto heat or not. See "Auto-heat" for  
more information.  
Turn on with + to:  
cook without auto-heat.  
Turn on with – to:  
cook with auto-heat.  
17  
 
Use  
Settings  
Power level*  
Use for  
standard extended  
factory settings settings**  
(9 power levels) (17 power levels)  
Melting butter  
Dissolving gelatine  
1 - 2  
3
1 - 2.  
3 - 3.  
Thickening sauces containing egg yolk and/or butter  
Warming small quantities of food/liquid  
Cooking rice  
Thaw frozen vegetables (blocks)  
Warming liquid and half-set foods  
Thickening sauces, e.g. Hollandaise  
Making oatmeal  
Preparing omelettes, lightly fried eggs  
Steaming fruit  
4
5
4 - 4.  
Defrosting deep frozen food  
Steaming vegetables, fish  
Cooking broths, soups  
5
Bringing large quantities of food to a boil  
Cooking dumplings  
6
7
5. - 6  
Gentle frying (without overheating the fat) meat, fish,  
vegetables, fried eggs  
6. - 7.  
Frying pancakes, etc.  
8
9
8 - 8.  
9
Boiling large quantities of water  
*
These settings are intended as guidelines only. With deep pans, larger quantities of food or when  
cooking without a lid, a higher setting is required. For smaller quantities, select a lower setting.  
** If you wish to fine-tune a setting, you can extend the power level range (see "Programming - P2").  
The intermediate setting will be represented by an indicator next to the number.  
18  
 
Use  
Auto-heat  
When Auto-heat has been activated,  
the burner switches on automatically at  
the highest setting and then switches to  
the continued power level which was  
selected. The "heat-up" time depends  
on which continued power level has  
been chosen (see table).  
Continued power  
level*  
Heat-up time  
(approx.)  
min : sec  
1
1.  
2
0 : 15  
0 : 15  
0 : 15  
0 : 15  
0 : 25  
0 : 25  
0 : 50  
0 : 50  
2 : 00  
5 : 50  
5 : 50  
2 : 50  
2 : 50  
2 : 50  
2 : 50  
2 : 50  
-
Taking a pan off the zone while  
Auto-heat is in operation interrupts the  
function. It will resume if a pan is  
placed back on the zone within  
3 minutes.  
2.  
3
3.  
4
4.  
5
5.  
6
6.  
7
7.  
8
8.  
9
*
The continued cooking settings with a dot  
after the number are only available if the  
power level range has been extended (see  
"Programming - P2").  
19  
 
Use  
Activating Auto-heat  
At any point during the Auto-heat time  
you can use + or - to lower or increase  
the continued power level. The  
^ Press the - sensor until the desired  
continued power level appears,  
e.g. 6.  
Auto-heat time will adjust accordingly.  
In the extended range of settings (see  
"Programming - P2"), A flashes  
alternately with the continued power  
level until the heat-up time has  
completed.  
During the heat-up time a dot will light  
to the right of the continued power  
level, and go out when it is completed.  
20  
 
Use  
Booster function  
The extra boost of energy is only  
available by taking a proportion of  
Each burner is equipped with a booster  
function to temporarily increase the  
power level. The front left burner is  
equipped with a double booster.  
When the booster function is on, the  
burners increase to power level 9 for  
10 minutes. This boost is intended  
quickly bring large quantities of water  
to the boil, e.g. when cooking pasta.  
A maximum of two booster functions  
can be used at one time.  
energy away from another burner. For  
this reason, the burners are networked  
in pairs as shown.  
When the booster is activated:  
– if Auto-heat is activated or either  
burner of the same network, it will  
switch off.  
If the booster is activated, when  
– no power setting is selected, the  
burner will revert to power level 9 at  
the end of the booster time or when  
the booster is switched off.  
– the power level on the other linked  
burner may decrease.  
– if the rear left burner is turned on, it  
will switch off if booster 2 for the front  
left burner is activated.  
– a power setting is selected, the  
burner will revert to this pre-selected  
power setting at the end of the  
booster time or when the booster is  
switched off.  
Taking a pan off the burner while the  
booster is in operation interrupts the  
booster function. It will resume if a pan  
is placed back on the burner within 3  
minutes.  
The booster can be switched off by  
touching the + and - sensor at the same  
time, or by touching the - sensor.  
21  
 
Use  
Single booster (all burners)  
^ Turn on the relevant burner.  
^ Select a power level.  
Double booster (front left burner  
only)  
^ Turn on the relevant burner.  
^ Select a power level.  
^ Take your finger off the sensor.  
^ Take your finger off the sensor.  
^ Touch the + and - sensor briefly at  
the same time.  
^ Touch the + and - sensor briefly at  
the same time.  
The indicator for the booster will light  
and I will appear in the burner display.  
The indicator for the booster will light  
and I will appear in the burner display.  
If power level 9 was selected, the  
booster can be activated by  
touching the + sensor only.  
^ Touch the + and - sensor briefly at  
the same time again.  
II will appear in the burner display.  
22  
 
Use  
Turning off a burner  
Residual heat indicator  
^ Touch the s On/Off touch control for The bars of the residual heat indicator  
the desired burner.  
go out one after another as the burners  
cool. The last horizontal line only goes  
out when the burner is safe to touch.  
The display will show - for a few  
seconds. If the burner is still hot the  
residual heat indicator will show.  
Turning off the cooktop  
^ Touch the s On/Off control for the  
cooktop.  
The residual heat indicator also  
reacts to hot dishes and plates  
being placed on a burner that is not  
switched on.  
All burners are turned off. If any burners  
are still hot the residual heat indicator  
will show in the respective display.  
Do not touch any burner or place  
any heat sensitive items on a burner  
where the residual heat indicator is  
lit. Danger of burns, and fire hazard.  
,Please note that the residual  
heat indicators do not light when  
there is a fault message, even if the  
burners are hot.  
23  
 
Timer  
The cooktop is fitted with a timer which  
can be used to time kitchen activities  
and/or to switch off the burners  
automatically.  
Setting the timer  
The timer can be used with the cooktop  
turned on or off. It works like a manual  
kitchen timer.  
You can set a time from 1 minute (01) to  
9 ½ hours (9.^). If the time is more than  
99 minutes (99), the setting will be  
shown in half-hour increments, which  
appear after the decimal point.  
^ Touch the m, - or + sensor.  
Two dashes appear in the display, and  
the timer indicator will flash.  
^ While the indicator is flashing, touch  
the - or + sensor until the desired  
time appears in the display,  
e.g. 15 minutes.  
Use the - and + touch controls to raise  
and lower the time. There are pre-set  
stops at 2 hours and at 99 minutes. To  
override a stop, briefly remove your  
finger from the touch control, then  
touch it again to continue.  
The time then counts down in minutes.  
The time remaining can be seen in the  
display and changed at any time by  
touching - or +.  
To re-set the display to 00,  
simultaneously touch - and +.  
When the set time has elapsed, 00 will  
appear in the timer display for a few  
seconds. At the same time an audible  
signal will sound for a few seconds. To  
turn the signal off before this, touch the  
m sensor.  
24  
 
Timer  
Automatic switch-off  
^ Touch the - or + sensor until the  
desired time appears in the display,  
e.g. 15 minutes.  
To use this feature, a power setting  
must be selected for the desired  
burner. All burners can be programmed The time then counts down in minutes.  
at the same time.  
The time remaining can be seen in the  
display and changed at any time by  
touching - or +.  
If the programmed time is greater  
than the maximum operating hours  
permitted, the cooktop will  
eventually switch-off automatically.  
See "Safety cut-out feature" for more  
information".  
If you want to set another burner to  
switch-off automatically, repeat the  
same steps.  
If more than one switch-off time is  
programmed, the shortest time  
^ Turn the desired burner on, e.g. rear  
right, and select a power level.  
remaining will show in the display, the  
indicator for that particular burner will  
flash. All the other indicators will remain  
lit. If you want to check the remaining  
time for another zone, touch the m  
sensor until the indicator for the desired  
burner flashes.  
^ Touch the m sensor.  
Two dashes appear in the display, and  
the timer indicator will flash.  
^ Touch the m sensor again.  
The indicator for the timer in the display  
goes out, and the automatic switch-off  
indicator flashes.  
^ If several burners are being used,  
touch the m sensor repeatedly until  
the indicator flashes next to the  
burner you wish to use this function  
for, e.g. back right.  
The indicator for the burners being  
used will light up clockwise, starting  
with the front left.  
25  
 
Timer  
Combi mode  
After the last entry, the shortest  
remaining time will appear in the  
display. If you want to check on another  
remaining time, touch the m sensor  
until the relevant indicator flashes.  
The timer and automatic switch-off  
functions can be used at the same  
time.  
If you have programmed in one or more  
switch-off times, and would like to use  
the timer as well:  
Touch the m sensor repeatedly until  
the timer indicator flashes.  
Starting with the shortest remaining  
time which is shown in the display, all  
burners that are in use and the timer  
can be selected clockwise.  
If you are using the timer, and would  
like to program one or more switch-off  
times as well:  
Touch the m sensor repeatedly until  
the indicator flashes for the desired  
burner.  
26  
 
Safety features  
Child Safety Lock  
Manual activation  
^ Press and hold the $ Child Safety  
Lock control until the respective  
indicator lights.  
Keep children away from the  
cooktop for their own safety.  
The cooktop has a Child Safety Lock to  
prevent children from turning on the  
burners or changing settings.  
The indicator will go out after a short  
time.  
You can alter the setting from one  
finger to three finger operation (see  
"Programming - P6") to make it harder  
for children to operate the appliance.  
The Child Safety Lock can be activated  
while the cooktop is on or off.  
Activating the Child Safety Lock  
during cooktop use  
– The settings for the burners and  
timer cannot be altered.  
Automatic activation  
The Safety lock will come on 5 minutes  
after the cooktop is switched off.  
– The burners and cooktop can still be  
turned off but once turned off cannot  
be turned on again.  
To use this feature the setting has be  
changed (see "Programming - P7").  
Activating the Child Safety Lock  
when the cooktop is turned off  
– The cooktop cannot be turned on.  
Deactivation  
^ Press and hold the $ Child Safety  
Lock control until the indicator goes  
out.  
The indicator will come on to show that  
the Child Safety Lock has been  
activated, if you touch the $ Child  
Safety Lock control or try to select a  
setting.  
In the case of a power failure the  
Child Safety Lock will be  
deactivated.  
27  
 
Safety features  
Stop and Go  
To deactivate Stop and Go:  
Your appliance has a Stop and Go  
feature which, when activated, reduces  
the power of all burners that have been  
switched on.  
^ Press and hold the $ control until the  
indicator goes out.  
The burners will now run at the level  
previously set.  
If you then deactivate the feature, the  
burners will automatically return to the  
previous level.  
If the feature is not deactivated, the  
cooktop will turn off after 1 hour.  
If you wish to use this feature, you will  
need to alter the factory setting (see  
"Programming - P1").  
To activate Stop and Go:  
^ Press and hold the sensor $ until you  
hear two consecutive beeps.  
Be careful not to continue touching  
the $ sensor for too long, as this will  
activate the safety lock.  
The Child Safety Lock indicator will  
flash. The power for the activated  
burner(s) will reduce to level 1, and 1  
will appear in the respective display.  
When activating "Stop and Go":  
– the countdown of the programmed  
time for the automatic switch-off  
function will be interrupted. When  
deactivating "Stop and Go", the  
countdown will continue,  
– the timer will continue without  
interruption.  
28  
 
Safety features  
Safety cut-out feature  
Covered touch controls  
The cooktop will turn off automatically if  
any of the touch controls are covered  
for more than 10 seconds, e.g. by  
finger contact, food boiling over or by  
an object such as an oven mitt or towel.  
A tone will also sound every 30 secs.  
for a maximum of 10 min and an F will  
flash in the display of the sensor which  
is covered.  
The cooktop is on too long  
The cooktop has a safety cut-out  
feature in case it is not turned off after  
use.  
If one of the burners is heated for an  
unusually long period of time (see  
table), and the power level settings are  
not adjusted, the cooktop will turn itself  
off automatically and the residual heat  
indicator will light.  
Power level*  
Maximum  
operating hours  
^ Clean the touch controls or remove  
the object covering it.  
1 / 1.  
2/ 2.  
3 /3.  
4 / 4.  
5 / 5.  
6 / 6.  
7 / 7.  
8 / 8.  
9
10  
5
This will turn off the signal tone and the  
displayed F will go out.  
^ Turn the cooktop on again with the s  
touch control. The burners can now  
be used.  
5
4
3
2
2
2
1
*
The power settings with a dot after the number  
are only available if the power setting range has  
been extended (see "Programming - P2.").  
^ To use the burners again, turn the  
cooktop back on in the usual way.  
29  
 
Safety features  
Overheating protection  
Overheating can be caused by:  
– heating an empty pan.  
The induction coils and the cooling  
element of the electronic are fitted with  
a overheating protection feature. This  
prevents the induction coils and cooling  
element from overheating.  
– fats or oils being heated on the  
highest power setting.  
– there being insufficient ventilation to  
the under side of the appliance.  
This mechanism works on the affected  
burner or on the entire cooktop in the  
following ways:  
If the overheating protection  
mechanism triggers again, contact  
Miele Technical Service.  
– If the booster function is being used,  
this will be switched off.  
– The power level will be reduced.  
– If an induction coil is affected, the  
cooktop will switch off. The fault  
code FE99 will be displayed.  
The burner can be used again as soon  
as it has cooled to a safe temperature.  
– If the cooling element is affected, the  
power supply to the burners will be  
reduced, and the set power level will  
continue to be displayed.  
As soon as the cooling element has  
cooled sufficiently, the burners will  
automatically continue to operate at the  
original power setting.  
30  
 
Cleaning and Care  
Do not use a steam cleaner to clean  
this appliance. Steam could  
penetrate electrical components and  
cause a short circuit. Pressurized  
steam could cause permanent  
damage to the surface and to  
components.  
Clean any spills immediately before  
they become difficult to remove.  
Clean the appliance regularly,  
preferably after each use. Allow the  
appliance to cool before cleaning.  
^ Wipe off any soiling using a damp  
cloth. Stubborn soiling is best  
removed with a shielded scraper  
blade.  
Do not use any sharp pointed  
objects which could damage the  
seal between the ceramic surface,  
the surrounding frame and the  
countertop.  
^ Apply a ceramic cleaner using a soft  
cloth or paper towel. To remove any  
limescale deposits or metallic residue  
apply a ceramic cleaner using a soft  
cloth and a shielded scraper blade if  
necessary.  
Never use abrasive or caustic (oven)  
cleaners, dishwasher detergent,  
scouring pads, steel wool or hard  
brushes. They will damage the  
surface.  
^ After cleaning wipe the ceramic  
surface with a damp cloth and dry.  
The ceramic surface can be cleaned  
using a cleaner for ceramic  
surfaces. Follow the manufacturer’s  
instructions.  
A cleaner with a special additive to  
prevent water marks and smears on the  
ceramic surface may be used.  
Any melted solids like sugar, plastic or  
aluminum foil should be removed as  
soon as possible, while the burner is  
still warm. If they are allowed to harden  
the cooktop may become pitted.  
Make sure that no cleaner residue  
remains on the ceramic surface by  
carefully wiping the cooktop with a  
damp cloth. They may damage the  
cooktop or produce toxic fumes  
when heated.  
^ Turn the burner off.  
^ Using a shielded scraper blade,  
scrape the melted item immediately  
off the burner while it is still hot.  
Use caution: Danger of burns!  
Be sure that pot and pan bases are  
clean and dry.  
After cleaning, dry the ceramic  
surface with a soft cloth to prevent a  
build up of limescale deposits.  
^ Allow the cooktop to cool and clean  
as previously described.  
31  
 
Programming  
The cooktop's default settings can be  
adjusted (see table).  
Saving the settings  
^ Press and hold the On/Off "s" touch  
control until the displays go out.  
^ While the cooktop is turned off, touch  
the On/Off "s" control and Child  
Safety Lock "$" control at the same  
time until the Child Safety Lock  
indicator flashes.  
Not saving the settings  
^ Press and hold the Child Safety Lock  
"$" control until the displays go out.  
The burner display shows P (Program)  
and S (Status) with a number. The  
number indicates the current setting.  
To set the desired program:  
^ Touch the + or – control of the front  
left burner to select the program  
desired.  
To set the status (see table):  
^ Touch the + or – control of the front  
right burner to select the desired  
status.  
Several programs can be adjusted one  
after another by repeating the steps  
listed above.  
32  
 
Programming  
Programming Table  
Program*  
Status** Setting  
P
0
Demonstration mode and  
factory default settings  
S
S
S
S
S
S
0
1
9
0
1
0
Demonstration mode on  
Demonstration mode off  
Restore Factory default settings  
P
P
1
2
Stop and Go  
Off  
On  
Power level range  
9 power levels  
(1 to 9)  
S
1
17 power levels  
(1, 1., 2, 2., 3 ... to 9)  
If the Auto heat setting is  
selected, an A will flash  
alternately with the continued  
power level in the display  
P
P
P
3
4
5
Warning tone when there  
is no pan or the pan is  
unsuitable  
S
S
S
S
S
S
S
S
S
S
S
S
0
1
2
3
0
1
2
3
0
1
2
Off  
Quiet  
Medium  
Loud  
Keypad tone when a  
control is touched  
Off  
Quiet  
Medium  
Loud  
Timer tone volume  
Off  
Quiet - 10 seconds  
Medium- 10 seconds  
Loud - 10 seconds  
3
* Programs / status not shown are not allocated.  
** The factory default setting is printed in bold.  
33  
 
Programming  
Program*  
Status** Setting  
P
P
6
7
8
Safety lock manual activation  
procedure  
S
0
One finger lock using $  
S
1
Three finger lock using $  
and + on the two right-hand  
burners  
Safety lock activation  
S
0
Manual activation  
S
1
Automatic activation 5  
minutes after cooktop is  
turned off  
P
P
Auto heat  
S
S
S
S
S
0
1
0
1
2
Off  
On  
6. Sensor reaction time  
Low  
Normal (300 ms)  
Fast  
* Programs / status not shown are not allocated.  
** The factory default setting is printed in bold.  
34  
 
Frequently asked questions  
Repairs should only be carried out by an authorized technician in accordance  
with local and national safety regulations. Unauthorized repairs could cause  
injury or appliance damage.  
What if the cooktop or the burners cannot be turned on?  
Possible fault  
The cookware is not suitable for an Use the correct pots and pans, see  
induction cooktop. "Cookware".  
Solution  
The Child Safety Lock is activated. Deactivate the safety lock.  
See "Child Safety Lock".  
The main fuse has blown.  
Check the main fuse.  
What if the burner does not heat up but can be turned on and a power level  
can be selected?  
Possible fault  
Solution  
The cooktop is in the demo mode. See "Programming - P0".  
What if a ß appears in a burner display?  
Possible fault  
The burner was turned on without Be sure the correct burner is turned on and  
a pan on it. a pan is on it.  
The cookware is not suitable for an Use the correct pots and pans, see  
induction cooktop. "Cookware".  
Solution  
What if a single burner or the whole cooktop switches itself off?  
The Safety cut-out or Overheating protection feature has been activated. See  
"Safety features".  
What if food does not cook when using auto-heat?  
Possible fault  
Solution  
The pot or pan does not transfer  
heat properly.  
Use the correct pots and pans, see  
"Cookware".  
Large amounts of food are being  
cooked.  
Select a higher continued power level.  
35  
 
Frequently asked questions  
What if one of the following has occurred?  
Possible fault  
Solution  
The booster has automatically switched  
off early.  
The overheating protecting feature has  
been triggered, see "Safety features".  
The power level has dropped.  
The burner is not working as usual.  
What if the cooling fan continues to run after the appliance has been  
switched off?  
This is not a fault. The fan will continue running until the appliance has cooled. It  
will then switch itself off automatically.  
What if an F appears in the display for the rear burners, an E appears in the  
display for the front burners and numbers appear in the timer display  
Possible fault  
Solution  
FE99  
The overheating protection mechanism  
has triggered. The burner can be used  
again as soon as it has cooled down to  
a safe level.  
Other fault messages  
Interrupt the power supply to the  
cooktop for approx. 1 minute.  
If the problem persists after  
reconnecting the appliance to the  
power supply, please contact the Miele  
Technical Service department.  
36  
 
Technical Service  
In the event of a fault which you cannot MieleCare  
easily fix yourself, please contact the  
(USA only)  
Miele Technical Service Department  
using the information on the back of this MieleCare, our Extended Service  
manual.  
Contract program; gives you the  
assurance of knowing that your  
appliance investment is covered by 5  
years of worry free ownership.  
MieleCare is the only Extended Service  
Contract in the industry that guarantees  
repairs by a Miele Authorized Service  
Provider using genuine Miele parts.  
Only genuine Miele parts installed by  
factory trained professionals can  
guarantee the safety, reliability and  
longevity of your Miele appliance.  
When contacting Technical Service  
quote the serial number and model of  
the cooktop. This information is visible  
on the silver data plate.  
Please note that unless expressly  
approved in writing by the Miele  
Service department, Extended Service  
Contracts offered by other providers for  
Miele products will not be recognized  
by Miele. Our goal is to prevent  
unauthorized (and untrained) service  
personnel from working on your Miele  
products, possibly doing further  
damage to them, you and/or your  
home.  
To learn more about MieleCare  
Extended Service Contracts, please  
contact your appliance dealer or visit  
us online at:  
37  
 
38  
 
Installation Instructions  
To prevent accidents  
and machine damage  
read these instructions  
before  
installation or use.  
 
IMPORTANT SAFETY INSTRUCTIONS  
Note to the installer:  
Please leave this instruction book  
with the consumer for the local  
electrical inspector’s use.  
2 ”  
The minimum distances given in  
these Installation Instructions must  
be observed in order to ensure safe  
operation. Failure to do so increases  
the risk of fire.  
recommended  
The cabinetry and venting hood  
should be installed first to prevent  
damage to the cooktop.  
The cooktop should only be installed  
~
as shown in the illustrations while  
maintaining the required safety  
distances shown. Do not install the  
cooktop between two tall cabinets, this  
is a fire hazard.  
2 ”  
50mm  
b
a A minimum distance of 2"  
(50 mm) from the cooktop to the rear  
wall and a side wall or cabinet must  
be maintained for safety.  
not recommended  
The countertop must be bonded  
~
with heat resistant (212 °F/100 °C)  
adhesive to prevent distortion or  
dissolving.  
The cooktop must not be installed  
~
over a dishwasher, washer, dryer,  
refrigerator or freezer. Heat radiated by  
the cooktop may damage them.  
not allowed  
The cooktop must only be installed  
~
above an oven if it has a built-in cooling  
fan.  
40  
 
IMPORTANT SAFETY INSTRUCTIONS  
To eliminate the risk of burns or fire  
~
by reaching over heated surfaces  
Safety distances above the  
appliance  
cabinet storage space above the  
cooktop should be avoided. If cabinet  
storage is necessary, the risk can be  
reduced by installing a venting hood to  
project horizontally a minimum of 5"  
(127 mm) beyond the bottom of the  
cabinets.  
Because of the heat radiated it is not  
~
recommended to install the cooktop  
above a drawer. It should be installed  
above a cabinet base unit with a  
dummy drawer front. A protective base  
should also be installed between the  
dummy drawer and the cooktop. There  
must be a minimum distance of 4 ½"  
(110 mm) between the top of the  
The minimum safety distance given by  
the hood manufacturer must be  
maintained between the cooktop and  
the hood above it. See the installation  
instructions of the hood for these safety  
measurements.  
countertop and the top of the protective  
base to ensure proper ventilation.  
This appliance has not been  
~
If the hood manufacturers instructions  
are not available or if flammable objects  
are installed over the cooktop (e.g.  
cabinets, utensil rail, etc.), a minimum  
safety distance of 30" (760 mm) must  
be maintained.  
designed for maritime use or for use in  
mobile installations such as recreational  
vehicles or aircraft. However, under  
certain conditions it may be possible for  
installation in these applications. Please  
contact the Miele Technical Service  
Department with specific requirements.  
If there is more than one appliance  
beneath a hood (e.g. wok burner  
and electric cooktop), and they have  
different minimum safety distances  
always observe the greater  
distance.  
The cooktop must not be  
~
permanently sealed into the countertop  
when installed. The sealing strip under  
the edge of the cooktop provides a  
sufficient seal for the countertop.  
Once installed, be sure that the  
~
power cord cannot come into contact  
with the underside of the cooktop or  
any mechanical parts.  
41  
 
Installation  
Cooktops flush with the countertop  
Frame/Facet cooktops  
aWall  
bWall covering  
cBack splash  
dCountertop  
eCountertop cut-out  
f2" (50 mm) minimum distance  
42  
 
Installation  
Installation dimensions  
29/16"  
1/4"  
20  
5/16"  
(514mm)  
(8mm)  
1/4"  
(65mm)  
31  
(794mm)  
b
ß3/16"  
R4mm)  
ß
max  
9/16"  
(
1
( 5002m"m)  
0
max  
40mm)  
(
19 11/16"  
11/16"  
)
+
1
(500+ mm)  
mm  
+
-
1/16"  
30  
-
1
-
(780  
a
c
3"  
(76mm)  
29/16"  
d
(65mm)  
a
1/2"  
12  
(317mm)  
9/16  
2
(65mm)  
aFront of cooktop  
bInstallation height  
cInstallation height power supply  
dPower cord encased by flexible metal conduit  
Length = 3' 11" (1200 mm) C = 3/4" (19 mm)  
43  
 
Installation  
Ventilation  
b
279/16"  
(700mm)  
3"  
c
(75mm)  
a
aFront of cooktop  
bCut-out at the rear wall of the cabinet for ventilation  
cProtective base  
If a protective base is fitted, there must be a distance of at least 4 ½" (110 mm)  
between the top of the protective base and the top of the countertop, for proper  
ventilation of the appliance. At the back there has to be a gap of 3" (75 mm) for  
the power cord.  
44  
 
Installation  
Cut out  
Installing the cooktop  
^ Make the countertop cut-out following ^ Feed the cooktop connection cable  
the dimensions given in the  
illustration.  
down through the cut-out.  
^ Place the cooktop centrally in the  
cut-out. When doing so make sure  
that the seal under the cooktop sits  
flush with the countertop on all sides.  
This is important to ensure an  
Remember to maintain a minimum  
distance of 2" (50 mm) between the  
rear wall and the right or left side.  
See also the "IMPORTANT SAFETY  
INSTRUCTIONS".  
effective seal. Do not use sealant.  
^ Seal the cut surfaces with a suitable  
heat-resistant sealant to avoid  
swelling caused by moisture.  
^ Connect the cooktop to the main  
power supply.  
^ Turn the cooktop on and check the  
function.  
If during installation the seal around  
the frame does not sit flush with the  
countertop in the corners, the corner  
radius, maximum 3/16" (4 mm), can  
be carefully filed down to fit.  
This cooktop has a seal underneath  
to keep it securely in position.  
Spring clips are not required. Any  
gap between the frame and the  
countertop will reduce as the  
cooktop is used.  
45  
 
Installation  
The sealing strip under the edge of the  
top part of the cooktop provides a  
sufficient seal for the worktop.  
Do not let sealant get in between the  
cooktop frame and the worktop.  
This could cause difficulties if the  
cooktop ever needs to be taken out  
for servicing and possibly result in  
damage to the cooktop frame or the  
worktop.  
46  
 
Electrical connection  
Connection  
,CAUTION: Before installation or  
servicing, disconnect the power  
supply by either removing the fuse,  
shutting off the main power supply  
or manually "tripping" the circuit  
breaker.  
The cooktop is equipped with a flexible  
metal conduit encasing 3 wires ready  
for connection to a grounded power  
supply.  
208/240 V, 60 Hz, 40 A fuse rating  
Black wire: connect to L1 (hot)  
Red wire: connect to L2 (hot)  
Green wire: connect to GND (ground)  
Installation work and repairs should  
only be performed by a qualified  
technician in accordance with all  
applicable codes and standards.  
Repairs and service by unqualified  
persons could be dangerous.  
A dedicated line and junction box  
should be used to connect the cooktop  
to a 40 A circuit..  
For further information, see the wiring  
diagram provided with the appliance.  
Before connecting the appliance to  
the power supply, make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This  
data must correspond to prevent  
appliance damage. Consult an  
electrician if in doubt.  
, WARNING:  
THIS APPLIANCE MUST BE  
GROUNDED!  
Only operate the cooktop after it has  
been installed into the countertop.  
Installer:  
Please leave these instructions with  
the consumer.  
Power supply  
^ Be sure your electrical supply  
matches the data plate.  
47  
 
Help protect our environment  
Disposal of packing materials  
Disposal of an old appliance  
The cardboard box and packing  
materials are biodegradable and  
recyclable. Please recycle.  
Old appliances contain materials that  
can be recycled. Please contact your  
local recycling authority about the  
possibility of recycling these materials.  
Ensure that any plastic wrappings,  
bags, etc. are disposed of safely and  
kept out of the reach of children.  
Danger of suffocation!  
Before discarding an old appliance  
disconnect it from the electrical supply  
and cut off the power cord to prevent it  
from becoming a hazard.  
48  
 
49  
 
50  
 
51  
 
Alterations rights reserved / 4513  
M.-Nr. 06 766 201 / 04  
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST  
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.  
 

Miele Clothes Dryer T 4422 C User Manual
Miele Cooktop KM 342G User Manual
Miele Washer W 4446 WPS User Manual
MTD Tiller 215 386 000 User Manual
NEC Projector V230 User Manual
NETGEAR Marine GPS System GS116Ev2 User Manual
NETGEAR Network Card WNHDE111 User Manual
Nokia Cell Phone N93 User Manual
Oreck Carpet Cleaner STEAM100 User Manual
Panasonic Video Game Controller AW RP120G User Manual