Miele Clothes Dryer T 1302 User Manual

Operating Instructions  
Vented Dryer  
T 1302  
To prevent accidents  
and machine damage,  
read these instructions  
before  
UV  
Installation or use.  
M.-Nr. 05 863 581  
 
IMPORTANT SAFETY INSTRUCTIONS  
Do not repair or replace any part of  
the appliance or attempt any  
servicing unless specifically  
recommended in these operating  
instructions. Repairs to electrical  
appliances should only be performed  
by qualified personnel. Incorrectly  
repaired machines may pose a  
considerable risk to the user.  
,WARNING - To reduce the risk of  
fire, electric shock, or injury to  
persons when using your appliance,  
follow basic precautions, including  
the following:  
Read all instructions before using  
the appliance.  
Do not dry articles that have been  
previously cleaned, washed,  
soaked or spotted with gasoline,  
dry-cleaning solvents or other  
flammable or explosive substances.  
They may give off vapors that could  
ignite or explode.  
Do not use heat to dry articles  
containing foam rubber or similarly  
textured rubber-like materials, or items  
containing hair spray, nail polish  
remover or similar substances.  
Clean the lint filter before or after  
each load.  
Do not allow children to play on or  
in the appliance. Close supervision  
is necessary when the appliance is  
used near children. Always close the  
door after use to prevent child hazards.  
Keep the area around the air intake  
(toekick) and adjacent surrounding  
areas free from lint, dust and dirt.  
The interior of the machine and  
exhaust duct should be cleaned  
periodically by qualified personnel.  
Before this appliance is removed  
from service or discarded, remove  
the door to the drying compartment.  
Do not place items exposed to oils  
in your dryer. Items contaminated  
with oils may contribute to a chemical  
reaction that could cause the laundry to  
catch fire.  
Do not reach into the dryer if the  
drum is moving.  
Do not install or store this  
appliance where it will be exposed  
to the weather.  
This dryer is intended for  
residential use only!  
Do not tamper  
with the controls.  
3
 
 
IMPORTANT SAFETY INSTRUCTIONS  
GROUNDING INSTRUCTIONS  
This appliance must be grounded.  
In the event of malfunction or  
breakdown, grounding will reduce the  
risk of electric shock by providing a  
path of least resistance for electric  
current.  
This appliance is equipped with a cord  
having an equipment-grounding  
conductor and a grounding plug. The  
plug must be plugged into an  
appropriate outlet that is properly  
installed and grounded in accordance  
with all local codes and ordinances.  
WARNING – Improper connection  
of the equipment grounding  
conductor can result in a risk of electric  
shock. Contact a qualified electrician if  
you are in doubt as to whether the  
appliance is properly grounded.  
Do not modify the plug provided  
with the appliance: if it will not fit  
the outlet, have a proper outlet installed  
by a qualified electrician.  
SAVE THESE INSTRUCTIONS  
4
 
Control panel  
a e- "PROGRAMS" buttons  
g "Start/Stop" button T  
For selecting a drying program.  
Starts and stops a program.  
Interrupts a program when pressed.  
b "OPTIONS" buttons  
Flashes during program selection  
and lights once the program starts.  
For selecting a drying option.  
c "DRYNESS" button  
h "Door" button  
For selecting the dryness level of  
finished laundry.  
Opens the door when the program  
has finished. If the dryer is on, the  
drum interior will light when the door  
is opened. If the door is left open, the  
light will go off after a few minutes to  
save energy.  
d "STATUS" display  
Shows the current cycle of the drying  
program.  
i "On/Off" button  
e "Buzzer" button  
Turns power to the machine on and  
off.  
When selected, a buzzer will sound  
at the end of a program.  
f "FAULT" indicators  
An illuminated indicator will alert you  
if the child lock has been activated  
or if a fault occurred.  
5
 
 
Before loading the dryer  
Program recommendations  
The dryer must be correctly installed  
and connected before the first use.  
Please refer to the "Installation  
Instructions".  
Normal  
– Cottons and Permanent Press blends  
Wrinkle-free  
^ Before using for the first time clean  
the drum with a cloth.  
– Permanent Press:  
select the Hand Iron dryness and  
reduce the load size for best drying  
results  
Before drying, check fabric care  
labels for special drying instructions.  
– Delicate fabrics, such as polyester:  
select the Gentle option to reduce  
creasing  
q Dry with normal temperature  
r Dry with low temperature  
(select "Gentle" option)  
s Do not dry in a tumble dryer  
– Pure linen and down filled items  
– Do not overload the drum!  
Woolens  
Overloading the dryer will result in  
poor drying results and wrinkling.  
– Wool and wool blends  
Knitted fabrics and flannel tend to  
shrink when washed and dried for  
the first time. Do not overdry these  
fabrics.  
Smooth  
– Linen  
– Permanent Press (cottons, blends  
and synthetics)  
To prevent discoloration, do not dry  
new, dark-colored fabrics with  
light-colored items.  
Sturdy  
– Durable Cottons and Permanent  
Press  
– Close zippers and tie up fabric belts  
and apron ties to prevent tangles  
and damage to clothing.  
Fluff / 20 min / 30 min  
– Do not dry items that may melt or  
ignite in the dryer, such as plastics,  
rubber or sneakers.  
– All fabric types  
6
 
 
Using the dryer  
1. Turn on the dryer and load  
the laundry  
2. Select a program  
^ Press the "On/Off" button to turn on  
the dryer.  
^ Press the "Door" button to open the  
door.  
^ Load the laundry loosely into the  
drum.  
^ Make sure the lint filters are in place.  
^ Close the door with a firm swing - do  
not push it shut.  
For best results use liquid fabric  
softener when washing laundry.  
Fabric softener sheets may clog the  
filters and cause the dryer to  
overheat.  
^ Press the e or - button until the  
desired program indicator lights.  
To prevent fabric damage, check  
that laundry will not be caught in the  
closed door.  
7
 
 
Using the dryer  
Program  
When to use  
Note  
Normal Available drying options: Turbo, Full load, Gentle, Anti-crease  
Extra Dry  
Multi-layer, mixed loads of sturdy cottons, The "Extra Dry" program should not be  
e.g. jeans, towels.  
selected for jersey materials.  
Items may shrink.  
More Dry  
Normal  
Uniform loads of cottons,  
e.g. sheets, underwear, socks.  
-
Knitted items that may shrink,  
If items are still damp, dry again using  
e.g. jersey material or lightweight cottons. "More Dry".  
Less Dry  
Hand Iron  
Cotton or linen fabrics to be left damp for  
ironing.  
-
If fabrics are too damp, dry again using  
"Less Dry".  
Rotary Iron  
Cotton or linen fabrics which will be ironed To prevent moisture loss, roll up the  
with a rotary iron.  
laundry until ready to iron.  
Wrinkle-free Available drying options: Turbo, Gentle, Anti-crease  
More Dry  
Synthetic permanent press items  
e.g. pants and shirts.  
-
Normal  
Permanent press and blended fabrics,  
e.g. cotton/synthetic.  
Less Dry  
Permanent press and blended fabrics  
requiring an ironed finish.  
Reduce load size for fabrics that wrinkle  
easily.  
Special Programs Available drying options: Anti-crease only available in Fluff,  
Sturdy  
Woolens  
Delicate items which allow machine  
drying.  
Remove items immediately at the end of  
the program, while still slightly damp.  
Allow items to air dry.  
Smooth  
Program for reducing creasing of cotton,  
linen or permanent press fabrics made of  
cotton, blends or synthetics.  
-
Sturdy  
Fluff  
Mixed loads of cotton and permanent  
press items.  
-
Individual items to be freshened and  
fluffed with cool air.  
Reduce load size.  
TIMED CYCLES Available drying options: Gentle, Anti-crease  
20 min  
For individual items or very small loads,  
e.g. beach towels, swimsuits.  
-
30 min  
8
 
Using the dryer  
3. Select a drying option  
(if needed)  
OPTIONS  
Turbo  
Fast drying for sturdy fabrics with  
increased temperature and a reduced  
program length.  
Full load  
Select this option for efficient drying of  
a standard size load.  
Gentle  
For drying delicate fabrics at a lower  
temperature with an extended program  
time.  
^ A drying option can be selected or  
deselected with each press of the  
button.  
Anti-crease  
Prevents wrinkles if laundry is not  
removed immediately after the end of a  
program. The drum periodically rotates  
for about 1 hour.  
9
 
 
Using the dryer  
4. Select the dryness level  
5. Select the buzzer (if desired)  
The dryness level can be selected in  
the "Normal" and "Wrinkle-free"  
^ Press the "Buzzer" button to have a  
tone beep at the end of the program.  
programs. (The dryness level of the  
other programs cannot be adjusted.)  
Indicator light:  
on = buzzer selected  
off = buzzer not selected  
Adjusting the buzzer volume:  
– the dryer must be on  
– the door closed  
– a program selected  
– if the "Buzzer" indicator is lit, press  
the "Buzzer" button so its indicator  
light goes out.  
^ Press and hold the "Buzzer" button  
until its indicator lights and you hear  
the desired volume and tone.  
^ Press the selection button until the  
desired indicator illuminates.  
In the "Wrinkle-free" program, only  
"More Dry", "Normal" and "Less Dry" can  
be selected.  
10  
 
 
Using the dryer  
6. Start the program  
7. At the end of a program  
The "Anti-crease/End" indicator will light  
at the end of a program and the buzzer  
will sound if it was selected.  
If a fault occurred, a "FAULT" indicator  
will light. See "Frequently asked  
questions" for details.  
^ Press the "Start/Stop T" button.  
Once the program starts, the current  
cycle of the program will be indicated  
in the "STATUS" display.  
^ Press the "Door" button.  
^ Open the door.  
^ Remove the laundry.  
^ Check that the drum is empty.  
^ Clean the lint filter after each use  
(see "Dryer care").  
^ Close the door.  
^ Press the "On/Off" button to turn off  
the dryer.  
11  
 
 
Using the dryer  
Canceling or changing a  
program  
Adding or removing laundry  
during a program  
^ Press and release the "Start/Stop T"  
button to stop the drying program.  
^ Turn off the dryer using the "On/Off"  
button.  
To continue drying:  
^ Press the "Door" button.  
^ Select the new program by pressing  
^ Open the door.  
the e or - button.  
,CAUTION - Do not touch the rear  
of the drum while adding or  
removing items! There is a danger of  
burns due to high temperatures in  
the drum.  
^ Select any desired options.  
^ Select a dryness level (available in  
the "Normal" and "Wrinkle-free"  
programs).  
^ Press and release the "Start/Stop T"  
button to start the new program.  
^ Add or remove items.  
^ Close the door.  
^ Turn the dryer back on with the  
"On/Off" button.  
12  
 
 
Child lock  
Child lock  
To deactivate the child lock  
When activated, the child lock prevents Repeat steps 1. to 5.  
the dryer from being operated by  
locking the control panel functions.  
The "Child lock" indicator will go out.  
The control panel is now unlocked.  
The dryer can be turned on but not  
started. The "Child lock" indicator will  
flash.  
6. Turn off the dryer using the "On/Off"  
button.  
The door can be opened.  
To activate the child lock  
1. Make sure the dryer is turned off and  
the door is closed.  
2. Press and hold the "Anti-crease" and  
"DRYNESS" buttons at the same time,  
hold until step 5.  
3. Turn on the dryer with the "On/Off"  
button.  
4. Press the "OPTIONS" button 3 times.  
5. Release the "Anti-crease" and  
"DRYNESS" buttons.  
The "Child lock" indicator will flash and  
the dryer is now locked.  
6. Turn off the dryer using the "On/Off"  
button.  
13  
 
 
Dryer care  
Cleaning the lint filter  
,A clogged filter is a fire hazard!  
The lint filter must be cleaned after  
every program.  
^ Wipe the lint off the filter with your  
hand (do not use any sharp objects!)  
^ Any lint remaining in the hollow part  
of the door can be removed through  
the gap at the bottom with a dust  
brush or vacuum.  
^ Open the door and remove the lint  
filter by gently lifting it upwards.  
^ Return the lint filter and close the  
door.  
The lint filter can be rinsed with hot  
water if necessary. The filter must be  
dried thoroughly before being returned  
to the dryer door.  
14  
 
 
Dryer care  
Cleaning the exterior and the  
control panel  
,To reduce the risk of electric  
shock, disconnect the dryer from the  
power supply by shutting off the  
power main, tripping the circuit  
breaker or unplugging the power  
cord before performing  
maintenance.  
Never use abrasive cleaners,  
scouring pads, steel wool or caustic  
(oven) cleaners on the dryer. They  
will damage the surface.  
^ The exterior and the control panel  
can be cleaned with warm water and  
liquid dish soap applied with a soft  
sponge.  
^ Wipe dry.  
Cleaning the drum  
^ The stainless steel surfaces of the  
drum can be cleaned using a  
non-abrasive stainless steel cleaner.  
^ Wipe clean with a soft cloth.  
15  
 
 
Dryer care  
Changing the light bulb  
^ Replace the light bulb with a  
temperature proof bulb, available  
from Miele.  
,To reduce the risk of electric  
shock, disconnect the dryer from the  
power supply by shutting off the  
power main, tripping the circuit  
breaker or unplugging the power  
cord before performing  
The light bulb must not exceed the  
maximum wattage listed on the data  
plate.  
^ Flip up the light bulb cover and press  
it firmly until it clicks into place.  
maintenance.  
^ Open the door.  
,Make sure the bulb cover is  
securely closed to prevent a short  
circuit or penetrating moisture.  
The bulb cover is located along the  
upper rim of the drum opening.  
^ Restore power.  
^ Slide a screwdriver with a wide head  
underneath the side edge of the bulb  
cover and twist (see illustration).  
^ Flip down the bulb cover.  
16  
 
 
Frequently asked questions  
What if the dryer will not run?  
Possible fault  
Fix  
The "Start/Stop T" button was not Make sure the dryer is on. Press the "Start/  
pressed. Stop T" button to begin the drying program.  
The circuit breaker tripped or the Make sure the dryer is plugged in or reset  
dryer is unplugged.  
the circuit breaker.  
The door is not closed.  
How do I prevent static cling?  
Close the door properly.  
Add fabric softener to laundry when washing or select the "Less Dry" setting on  
the dryer.  
What if the drum light does not come on?  
Possible fault  
Fix  
The bulb may be bad or burned  
out.  
See "Changing the light bulb."  
What if the "Child Lock" indicator flashes after turning the dryer on and a  
program cannot be started?  
Possible fault  
Fix  
The child lock is activated.  
Deactivate the child lock. See "Child Lock."  
What if the program stops, the "Anti-crease / End" indicator lights and the  
buzzer sounds?  
Possible fault  
Fix  
The drum is empty.  
Load laundry into the dryer. The dryer will not  
operate when the drum is empty. Single  
items should be dried with "Sturdy" or a  
timed program and dry items in the "Fluff"  
program.  
What if the "Filter/Vent" fault indicator is lit?  
Possible fault  
Fix  
The lint filter is clogged.  
Clean the lint filters. See "Dryer care".  
The exhaust hose or the  
connection is clogged with lint.  
Remove lint and check the exhaust system  
for blockages.  
The air supply in the room is  
insufficient.  
Open a window or door to increase airflow.  
17  
 
 
Frequently asked questions  
What if the "Filter/Vent" indicator lights after cleaning the exhaust system?  
Possible fault  
Fix  
The dryer is not operating efficiently  
because the duct hose is too long.  
Check the exhaust length and diameter  
(see "How to calculate the effective  
duct length"). A long exhaust hose will  
increase program times and energy  
consumption.  
If the exhaust hose cannot be  
shortened, the indicator can be turned  
off by a service technician.  
What if the program runs too long or stops?  
Possible fault  
Fix  
The airflow is insufficient in the area of Open a window or door to increase  
the dryer.  
airflow.  
The lint filters are clogged.  
Clean the lint filters (see "Dryer care").  
The laundry was not spun sufficiently in Select a higher spin speed in the wash  
the washer.  
program.  
The dryer is overloaded.  
Reduce the load size.  
Metal zippers interfere with the dryer’s Select a timed program to avoid  
moisture sensors. overdrying.  
An airflow gap of 3/8" (10 mm) must be This gap must not be blocked by a  
provided between the machine and the toekick or thick piled carpets for  
floor.  
sufficient airflow.  
What if the laundry is not dry enough?  
Possible fault  
The load contained too many dissimilar items (size and fabric.)  
What if water has collected around the drum opening?  
Possible fault  
This is condensed moisture from the laundry.  
18  
 
Quick Guide  
Remove this guide for easy reference  
Please read all  
instructions, especially  
the "Important Safety Instructions",  
before using the dryer.  
 
 
Quick Guide  
1.Turn on the dryer and load the  
laundry  
2. Select a program  
^ Press the "On/Off" button to turn on  
the dryer.  
^ Press the "Door" button to open the  
door.  
^ Load the laundry into the drum. Make  
sure that there is enough space in the  
drum for clothes to tumble freely.  
^ Press the e or - button until the  
desired program indicator lights.  
3. Select a drying option (if needed)  
To prevent fabric damage, check  
that laundry will not be caught in the  
closed door.  
^ A drying option can be selected or  
deselected with each press of the  
button.  
^ Close the door with a firm swing - do  
not push it shut.  
 
Quick Guide  
4. Select the dryness level  
5. Select the buzzer (if desired)  
6. Start the program  
^ Press the "Start/Stop T" button.  
7. At the end of a program  
The "Anti-crease / End" indicator will  
light.  
^ Press "Door" and remove the laundry.  
^ Clean the lint filter.  
^ Press the selection button until the  
desired indicator illuminates.  
^ Press the "On/Off" button to turn off  
the dryer.  
 
Quick Guide  
Program  
When to use  
Note  
Normal Available drying options: Turbo, Full load, Gentle, Anti-crease  
Extra Dry  
For laundry to be folded and shelved  
immediately, e.g. jeans, towels.  
The "Extra Dry" program should not be  
selected for jersey materials.  
Items may shrink.  
More Dry  
Normal  
For uniform loads, e.g. sheets,  
underwear, socks.  
-
For knitted items that may shrink, e.g. If items are still damp, dry again using  
jersey material or lightweight cottons.  
"More Dry".  
Less Dry  
Hand Iron  
For items to be left damp for ironing.  
-
If fabrics are too damp, dry again using  
"Less Dry".  
Rotary Iron  
For items to be ironed with a rotary  
iron.  
To prevent moisture loss, roll up the  
laundry until ready to iron.  
Wrinkle-free Available drying options: Turbo, Gentle, Anti-crease  
More Dry  
For items that do not require ironing,  
e.g. pants and shirts.  
-
Normal  
For items to be hung after drying.  
For items which require ironing.  
Less Dry  
Reduce load size for fabrics that wrinkle  
easily.  
Special Programs Available drying options: Anti-crease only available in Fluff,  
Sturdy  
Woolens  
Delicate items which allow machine  
drying.  
Take items out immediately after the end  
of the program while still slightly damp.  
Allow items to air dry.  
Smooth  
Program for reducing creasing in  
delicate items.  
-
Sturdy  
Fluff  
For mixed loads of durable items.  
-
Individual items to be freshened and  
fluffed with cool air.  
Reduce load size.  
TIMED CYCLES Available drying options: Gentle, Anti-crease  
20 min  
Individual items or very small loads,  
e.g. beach towels, swimsuits.  
-
30 min  
Individual items or very small loads,  
e.g. beach towels, swimsuits.  
 
Technical Service  
In the event of a fault you cannot fix  
yourself, please contact the Miele  
Technical Service Department  
PC Update  
The indicator on the control panel  
marked PC allows a technician to  
update the dryer to make use of new  
technology.  
U
V
1-800-999-1360  
For example, if new programs or fabrics  
are developed, a service technician will  
be able to modify the existing program  
cycles accordingly.  
1-800-565-6435  
When contacting Technical Service,  
please quote the model and serial  
number of your appliance. They can be  
found on the data plate located below  
the drum opening.  
19  
 
 
20  
 
Installation Instructions  
 
 
IMPORTANT SAFETY INSTRUCTIONS  
Installation, repair and  
maintenance work should be  
performed by a Miele authorized  
This dryer must be vented  
outdoors to reduce the risk of fire.  
Be sure to observe local building  
service technician. Work by unqualified codes.  
persons could be dangerous and could  
Use flexible or rigid metal pipe for  
void the warranty.  
venting. Non-metallic flexible hose  
should not be used, it is a potential fire  
hazard.  
Before installation, disconnect the  
tumble dryer from the electrical  
supply by shutting off the power main,  
unplugging the power cord or tripping  
the circuit breaker. Do not restore  
The dryer exhaust must not be  
connected to a chimney, ducting  
which ventilates rooms with fireplaces,  
a combustion appliance vent flue, a  
wall, ceiling or concealed space of a  
building.  
power until the installation is complete.  
GROUNDING INSTRUCTIONS  
This appliance must be grounded.  
In the event of malfunction or  
If there is any doubt concerning  
installation, contact Miele’s  
Technical Service Department.  
breakdown, grounding will reduce the  
risk of electric shock by providing a  
path of least resistance for electric  
current. This appliance is equipped  
with a cord having an equipment  
grounding conductor and a grounding  
plug. The plug must be plugged into an  
appropriate outlet that is properly  
installed and grounded in accordance  
with all local codes and ordinances.  
U
V
1-800-999-1360  
1-800-565-6435  
WARNING – Improper connection  
of the equipment grounding  
conductor can result in a risk of electric  
shock. Check with a qualified  
electrician or service representative or  
personnel if you are in doubt as to  
whether the appliance is properly  
grounded.  
Do not modify the plug provided  
with the appliance! If it will not fit  
the outlet, have a proper outlet installed  
by a qualified electrician.  
22  
 
 
Caring for the environment  
Disposal of the packing  
materials  
Disposal of an appliance  
Old appliances may contain materials  
that can be recycled. Please contact  
your local recycling authority about the  
possibility of recycling these materials.  
The cardboard box and packing  
materials protect the appliance during  
shipping. They have been designed to  
be biodegradable and recyclable.  
Ensure that a discarded dryer presents  
no danger to children. While being  
stored for disposal remove the door to  
the drying compartment.  
To prevent suffocation of children,  
ensure that any plastic wrappings,  
bags, etc. are disposed of safely and  
kept out of the reach of children.  
23  
 
 
Washer / Dryer Stack  
The tumble dryer can also be placed  
Height of vent adapter in a stacked  
on top of a Miele washing machine for a installation  
stacked installation. An appropriate  
Miele washer with a flat or angled  
control panel  
stacking kit is required. The stacking kit  
is available from your Miele dealer or  
the Miele Technical Service  
Department.  
,Installation of the stacking kit  
must be performed by a Miele  
authorized technician.  
5’ 6 3/8" (168.6 cm)  
Stacking kit with a pull out shelf  
24  
 
 
Electrical connection  
The dryer comes with a 5 ft long, 12/4  
AWG cord and a NEMA 14-30 P plug.  
GROUNDING INSTRUCTIONS  
This appliance must be grounded.  
In the event of malfunction or  
breakdown, grounding will reduce  
the risk of electric shock by  
providing a path of least resistance  
for electric current. This appliance is  
equipped with a cord having an  
equipment grounding conductor and  
a grounding plug. The plug must be  
plugged into an appropriate outlet  
that is properly installed and  
It should be connected to a  
120/208-240 V, 15 A, 60 Hz AC power  
supply. A 3 pole-4 wire grounding  
power outlet (NEMA type 14-30 R) is  
necessary.  
EASY INSTALLATION KIT  
If you do not have a dedicated 15 Amp  
line for this appliance, but you have the  
standard, 120/208-240 V - 30 Amp,  
60 Hz AC outlet, you can use the "Easy  
Installation Kit", which allows you to use  
that line to connect the dryer to power.  
grounded in accordance with all  
local codes and ordinances.  
WARNING – Improper connection of  
the equipment grounding conductor  
can result in a risk of electric shock.  
Check with a qualified electrician or  
service representative or personnel  
if you are in doubt as to whether the  
appliance is properly grounded.  
057B for on-site outlet NEMA 10-30 R  
060B for on-site outlet NEMA 14-30 R  
For more information on the "Easy  
Installation Kit" or if you have questions  
concerning the electrical connection,  
please contact:  
U
1-800-999-1360  
Do not modify the plug provided with  
the appliance! If it will not fit the  
outlet, have a proper outlet installed  
by a qualified electrician.  
V
1-800-565-6435  
25  
 
 
Installation  
a Exhaust connection:  
The exhaust hose can be installed  
either at the rear, left or right of the  
dryer.  
c Control panel  
d Door  
e Four height adjustable feet  
b Power cord with plug  
26  
 
 
Installation  
Leveling the dryer  
The machine can be leveled by turning  
the legs clockwise or counterclockwise  
as necessary.  
The dryer must be level to ensure safe  
and proper operation. Minor  
discrepancies do not have an adverse  
effect on operation.  
27  
 
 
Installation  
Determining the position of the  
exhaust connection  
The exhaust connection can be left at  
the rear of the dryer (factory standard)  
or moved to the left or right side of the  
dryer.  
Changing the position of the exhaust  
connection  
^ Remove the exhaust connection  
cover on the left or right side of the  
dryer.  
^ Press the supplied cover firmly into  
^ Do this by inserting a screwdriver into  
each raised flap and lifting upwards,  
as shown.  
the rear opening.  
^ To remove the cap insert a  
screwdriver between the machine  
and the cap and lift upwards, the cap  
will then pop out of place.  
This cover is no longer needed.  
28  
 
 
Installation  
Installation tips  
Adapter  
A ring adapter is supplied with the  
machine, and is compatible with all  
venting systems. The adapter helps  
prevent heat from escaping, and heats  
the air in the drum faster.  
An airflow gap of 3/8" (10 mm) must  
be provided between the machine  
and the floor. This airflow gap must  
not be blocked by a toekick or thick  
piled carpets.  
Do not install the dryer next to a  
refrigerator. The warm air exhausting  
from the dryer can affect the  
thermostat of the refrigerator,  
causing it to run continuously.  
^ The adapter, 1, is inserted into the  
connector, 2.  
Using the adapter with a maximum duct  
length of 33 ft (10 m) will result in  
shorter drying times and energy  
savings.  
29  
 
 
Installation  
Exhaust connection with a  
flexible exhaust hose or rigid  
pipe  
Window connection  
Using the connector supplied, an  
exhaust hose (4" [100 mm]  
diameter) can be installed.  
Necessary materials:  
– a wall or window duct  
– an exhaust hose made of approved  
non-flammable material  
1 Window connection (installed in a  
plexiglass pane)  
2 Connector for the flexible exhaust hose  
Wall connection with rigid pipe  
^ If the duct length is more than 33 ft  
(10 m), remove the ring adapter, 1,  
from the connector, 2. If the duct  
length is less than 33 ft (10 m), leave  
the ring adapter in to improve time  
and energy efficiency.  
^ Install the connector, 2, with the  
exhaust hose or pipe, 3, to the dryer.  
1 Wall pipe  
2 Connector  
3 Rigid pipe  
30  
 
 
Installation  
Direct wall connection  
Necessary materials:  
– a wall pipe  
Dryer side view  
– flexible foam gasket  
Dryer top view  
1 Wall pipe  
2 Flexible foam gasket  
1 Wall pipe  
2 Flexible foam gasket  
^ Insert the ring adapter, 1, into the wall  
pipe.  
Connect the flexible foam gasket, 3,  
to the wall pipe connector, 2.  
^ Push the dryer to the wall.  
31  
 
 
Installation  
How to calculate the effective  
duct length  
Tips about the ductwork  
– Check with your local building code  
to determine the maximum allowable  
duct length.  
The overall duct length will determine  
the duct diameter.  
– Use flexible metal pipe or rigid metal  
pipe for venting. Non-metallic flexible  
hose should not be used, it is a  
potential fire hazard.  
^ Measure the actual duct length  
needed to go from the dryer’s  
exhaust connection to the vent outlet:  
1. Establish the number of elbows or  
bends necessary, noting the type of  
bend, angle and radius involved  
(see Table).  
– For best drying results avoid extra  
long ducting with too many bends,  
angles or tight corners.  
– The shorter the exhaust ductwork,  
the more efficient the dryer will be.  
Expelled air is slowed down in the  
ducts due to friction against the inner  
walls. The shorter and smoother the  
inner walls are, the less friction will  
be created.  
2. Add the additional duct length (as  
derived by using the values  
specified in the table) and the actual  
duct length to get the effective  
length.  
Note:  
– An elbow or bend creates more  
friction than a straight duct. An  
additional duct length factor must be  
added for each elbow or bend (see  
Table). This factor expresses the  
resistance of the bend in terms of a  
straight length of duct.  
Maximum effective duct lengths:  
4" (100 mm) diameter  
5" (125 mm) diameter  
6" (150 mm) diameter  
66 ft (20 m)  
132 ft (40 m)  
328 ft (100 m)  
Using the ring adapter up to an  
effective duct length of 33 ft (10 m) and  
a standard duct diameter of 4"  
(100 mm) will provide optimal drying  
times and energy consumption.  
The additional length factor is then  
added to the existing duct to give the  
effective length.  
A larger duct diameter helps reduce  
friction. Therefore the duct diameter  
and length should be increased  
simultaneously.  
Do not use the ring adapter if the  
effective duct length is more than 33 ft  
(10 m).  
Effective duct lengths over 66 ft (20 m)  
require a larger duct diameter.  
Longer ducts may lead to slight  
decreases in dryer efficiency if the  
necessary duct diameter is not  
employed.  
32  
 
 
Installation  
Additional duct lengths (4" rigid pipe only)  
Type of bend  
RadiusAdditional  
ft  
cm  
ft  
cm  
Flexible metal duct  
3’ 3" (1 m) straight  
45° angle  
5’ 11"  
4’ 11"  
8’ 2"  
180  
150  
250  
10"  
10"  
25  
25  
90° angle  
Smooth metal duct  
3’ 3" (1 m) straight  
45° angle  
3’ 3"  
1’ 11"  
2’ 7"  
100  
60  
80  
10"  
10"  
25  
25  
90° angle  
Elbow 90° sharp  
7’ 6"  
2’ 4"  
230  
70  
Concertina bend  
90° angle  
8"  
20  
Wall vent or window vent  
with louvers  
with flap  
12’ 5"  
4’ 11"  
380  
150  
Exhaust connection  
left or right side  
3’ 3"  
100  
33  
 
Installation  
Example: Calculating the effective duct length and required internal  
duct diameter  
Rigid pipe  
A
Duct length  
ft  
Duct length  
m
12’ 5"  
3.8 m  
Wall duct with  
louvered wall vent  
B
2’ 7"  
1’ 7"  
2’ 7"  
3’ 3"  
22’ 5"  
0.8 m  
0.5 m  
0.8 m  
1.0 m  
6.9 m  
90° bend  
C
20" (0.5 m) rigid pipe  
90° bend  
D
E
left vent opening  
Total duct length  
The total duct length is less than 33 feet (10 m), so a duct diameter of 4" (100 mm)  
with adapter is sufficient.  
34  
 
35  
 
All rights reserved / 4804  
M.-Nr. 05 863 581 / 05  
 

Milwaukee Outdoor Fireplace LMDVT 3328CNM User Manual
NEC Projector M300WS User Manual
Nespresso Coffeemaker A GCA1 US BK NE User Manual
Omega Cordless Telephone OMA P1104 User Manual
Omega Thermometer TX82B User Manual
Omnimount TV Mount OM1100155 User Manual
Oregon Scientific Watch SL110 User Manual
Panasonic TV DVD Combo AJ SD955Bp User Manual
Panasonic VCR AJ HD1400E User Manual
Partner Tech Chainsaw 530084168 User Manual