MTX Audio Speaker 600WM User Manual

21A2695  
FIRST  
CLASS  
STAMP  
HERE  
MODEL 600WM  
WATER RESISTANT  
IN CEILING LOUDSPEAKER  
4545 E BASELINE RD  
PHOENIX AZ 85040-6400  
OWNERS MANUAL  
 
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX  
MTX offers a wide assortment of audio components. Ranging from in-wall speakers to  
amplifiers to accessories. Each component is value engineered and must meet strict  
quality control standards before it becomes part of the MTX product line.  
THE MODEL 600WM WATER RESISTANT LOUDSPEAKER  
The MODEL 600WM is specifically designed for use in areas where moisture is  
present, such as bath, sauna, hot tub area, patio, poolside and other exterior appli-  
cations. If you are planning an installation of this type, we strongly recommend  
the MODEL 600WM Water Resistant Loudspeaker.  
Listed below you will find a sampling of MTX components available from your autho-  
rized Blueprint Series dealer.  
IN-WALL LOUDSPEAKERS  
MODEL 520W  
LOUDSPEAKER PLACEMENT  
MODEL 502W  
5-1/4” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
5-1/4” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
45 Watts RMS/140 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
MTX In-Walls can be positioned virtually anywhere you desire sound. Important  
considerations are room layout, furniture arrangement, location of audio/video  
equipment and daily foot traffic within the room/house. MTX In-Walls are  
designed to be installed between wall studs, so avoid locations next to doors,  
windows or other construction that may present difficulties. If used for video, In-  
Walls should be placed at least six feet away from your video screen, to avoid  
magnetic interference.  
MODEL 620W  
6-1/2” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
55 Watts RMS/180 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
MODEL 602W  
6-1/2” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
MODEL 820W  
8” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/86dB Sensitivity  
33Hz-20kHz Frequency Response  
60 Watts RMS/200 Watts Total  
14-1/16”H x 10-1/16”W x 3-1/2”D  
SPEAKER/AMPLIFIER SELECTOR  
LPS-600  
Accommodates up to 6 pair of speakers  
Handles up to 250 Watts/channel continuous (RMS)  
Impedance Protection Circuitry  
Low profile-full size component  
Two-piece, plug in connectors on the rear panel  
Accommodates up to 14 gauge wire  
TV-5 UL Approved Switches  
Drop ceiling wiring example  
Exterior soffit example  
Baseboard/carpet wiring  
example  
A/B Amplifier and Input Selector  
ACCESSORIES  
VC-30B/VC-30W  
Decora-Style Volume Control (Bone or White)  
10 Step 25 Watts per channel (RMS) 150 Watts Peak  
AB-1SB/AB-1SW  
Decora-Style A/B Switch (Bone or White)  
PCK65C  
Pre-Construction Kit for Model 610RCM  
Attic wiring example  
Basement wiring example  
PCK85C  
Pre-Construction Kit for Model 810RCM  
 
STEP 1  
STEP 4  
Using a stud finder (available at low cost at most hardware stores) or other accu-  
rate method, locate center point between two studs and mark. Using template  
provided, trace hole pattern on surface of wall. Placing a bubble level on either  
the horizontal or vertical guidelines of template will assist you in leveling hole  
pattern.  
Attach loudspeaker wires to speaker terminals, observing correct polarity, and  
position speaker frame assembly to hole as shown. Insert top of mounting frame  
into hole at top. By moving bottom of frame upwards, you should now be able  
to insert bottom of frame into hole at bottom. Be careful not to pinch wires in the  
process. Tighten long screws. Use a level during tightening to insure straightness  
of final position.  
STEP 2  
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol-  
lowing traced pattern.  
STEP 5  
After the speaker panel is secured tightly, test for sound. When you are satisfied  
the speaker is operational, affix grill. As grill is designed for a snug fit, you’ll  
need to position one edge into slot first, and press or squeeze around perimeter  
of grill, while pushing leading edges into grill slot.  
STEP 3  
Run loudspeaker wires to sound source location. There are several methods you  
can use to accomplish wiring, depending on the construction characteristics of  
the room or house (see Loudspeaker Placement). You can add a professional  
touch to your installation by using a speaker terminal plate at the source location.  
Leave sufficient amount of wire at speaker location (8 to 10 inches) to complete  
connection.  
 

Miele Ventilation Hood DA2900 User Manual
Miller Electric Welding System A1D 4RV User Manual
National Instruments Computer Hardware PXI 8150 User Manual
NETGEAR Switch M4100 12GF User Manual
Nilfisk Advance America Lawn Sweeper SR 1100S B User Manual
NordicTrack Home Gym NTEL42550 User Manual
Oki All in One Printer 18 24DXE 2 User Manual
Olympus Camera Flash FL 36 User Manual
Panasonic Automobile Electronics DMC TZ20 User Manual
Panasonic Network Card 2SA2021G User Manual